At this present time our store location is open by appointment only.

6.5" Driver

Automotive Speakers and Accessories with a Driver Size of 6-1/2"

Automotive Speakers and Accessories with a Driver Size of 6-1/2"

51 products

  • JL Audio C1-650 : 6.5" Component Speakers - 50W RMS JL Audio C1-650 : 6.5" Component Speaker crossover.

    JL Audio C1-650 : 6.5" Component Speakers, 50W RMS

    6 Available for pickup

    C1-Series 6.5-Inch 50-Watt Component Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C1-650 Manual

    6 Available for pickup

    $159.99

  • Metra 82-8148 : 6"-6.75" Door Speaker Replacement Trim Ring, 2001-UP Lexus Subaru Toyota

    Metra 82-8148 : 6"-6.75" Door Speaker Replacement Trim Ring, 2001-UP Lexus Subaru Toyota

    3 Available for pickup

    Replacement Six-Inch to 6-3/4-Inch Door Speaker Trim Ring Adapter for Select 2001-UP Lexus, Subaru and Toyota Vehicles Provides spacing for aftermarket speaker installation. Works with all varieties of speakers including component drivers Accommodates 6" to 6.75" speaker – pair Front Speaker Applications LEXUS CT 200h 2011-2017 TOYOTA C-HR 2018-2020 Camry w/ amp 2018-2020 Camry w/o amp 2018-2020 Corolla Hatchback 2019-2020 RAV4 2019-2020 RAV4 2014.5-2018 RAV4 2013-2014.5 RAV4 2006-2012 RAV4 2001-2005 Rear Speaker Applications LEXUS RX Series 1999-2003 SUBARU Crosstrek 2018-2020 Impreza 2017-2020 Legacy 2015-2020 TOYOTA Avalon 2019-2020 C-HR 2018-2020 Camry w/ amp 2018-2020 Camry w/o amp 2018-2020 Camry 2021-2022 Corolla 2019-2020 Corolla Hatchback 2019-2020 Highlander w/ JBL amp 2020-2020 Highlander 2014-2019 RAV4 2019-2020 RAV4 2014.5-2018 RAV4 2013-2014.5 RAV4 2006-2012 RAV4 2001-2005 Tacoma 2021-2022 Tacoma 2019-2020 Tacoma 2005-2015 Tundra 2014-2018

    3 Available for pickup

    $25.99

  • JL Audio C1-650x : 6.5" Coaxial Speakers - 50W RMS JL Audio C1-650x : 6.5" Coaxial Speakers - 50W RMS, front side.

    JL Audio C1-650x : 6.5" Coaxial Speakers, 50W RMS

    Pre-Order Today!

    C1-Series 6.5-Inch 50-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many "6-inch" speaker locations as well. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 24 KHz ± 3 dB JL Audio C1-650x Manual

    Pre-Order Today!

    $129.99

  • Kicker 47KSC6504 : 6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS, top side. Kicker 47KSC6504 : 6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS, shown with grille.

    Kicker 47KSC6504 : 100W 6.5" Coaxial Speakers

    3 Available for pickup

    6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS The Kicker KS series six-and-a-half-inch coaxial speakers come with three custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 100 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6-1/2, 160 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-100 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 43-21k Mounting Hole Diameter [in, mm] 4-13/16, 123 Top Mount Depth [in, mm] 1-13/16, 46 Bottom Mount Depth [in,mm] 2-3/16, 54 Tweeter Protrusion [in,mm] 5/16, 8 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    3 Available for pickup

    $129.99

  • 6.5" Coaxial Speakers, 100W : Kicker 46CSC654 6.5" Coaxial Speakers, 100W : Kicker 46CSC654 shown without grille.

    Kicker 46CSC654 : 100W 6.5" Coaxial Speakers

    3 Available for pickup

    100-Watt 6.5-Inch Coaxial Speakers, 4-Ohm These CS series 6.5" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 100W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. These Kicker CS series 6 and a 1/2" speakers work best with 100 watts of recommended power. Specifications Speaker Design 2 - way Woofer Size | in [mm] 6 1/2 [160] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.3 Peak Power | Watts 300 Continuous Power | Watts, RMS 100 Sensitivity [SPLo] | dB @ 1W, 1m 90 Effective Frequency Range | Hz 40-20k Mounting Hole Diameter | in [mm] 4 13/16 [123] Top Mount Depth | in [mm] 3/8 [9] Bottom Mount Depth | in [mm] 1 11/16 [43] Tweeter Protrusion | in [mm] 0 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material PEI [polyether imide] Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam Kicker CS Series Coaxial Speaker Manual

    3 Available for pickup

    $89.99

  • JL Audio C3-650 : 6.5" Convertible Component Speakers - 75W RMS JL Audio C3-650 : 6.5" Convertible Component Speaker.

    JL Audio C3-650 : 6.5" Convertible Component Speakers, 75W RMS

    Pre-Order Today!

    C3-Series 6.5-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650 system features 6.5-inch (165 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-650 Manual

    Pre-Order Today!

    $549.99

  • Metra 82-3006 : 6"-6.75" Door Speaker Replacement Trim Ring, 2006-UP Buick Cadillac Chevy GMC

    Metra 82-3006 : 6"-6.75" Door Speaker Replacement Trim Ring, 2006-UP Buick Cadillac Chevy GMC

    2 Available for pickup

    Six-Inch to Six-3/4" Door Speaker Replacement Adapter Plates for Select 2006-UP Buick, Cadillac, Chevy and GMC Vehicles Vehicle specific spacer designed for installation of 6 to 6.75 inch aftermarket speakers One pair of adapters included in each package Front Speaker Applications BUICK Enclave 2008-2012 LaCrosse 2014-2019 Lucerne 2006-2011 CADILLAC Escalade, Escalade ESV, Escalade EXT 2007-2014 SRX 2010-2016 CHEVEROLET Avalanche 2007-2013 Cruze 2019-2019 Cruze 2011-2015 Impala 2006-2013 Malibu 2008-2012 Silverado 2500HD, 3500HD, Chassis Cab 2014-2014 Silverado 2500HD, 3500HD, Chassis Cab 2014-2014 Silverado 2500HD, 3500HD, Chassis Cab 2014-2014 Silverado new body style 2007-2007 Silverado new body style 2007-2007 Silverado new body style 2007-2007 Silverado 2008-2013 Silverado 2008-2013 Silverado 2008-2013 Spark 2016-2020 GMC Sierra / Sierra Denali 2500 HD, 3500 HD, Chassis Cab 2014-2014 Sierra / Sierra Denali 2500 HD, 3500 HD, Chassis Cab 2014-2014 Sierra / Sierra Denali 2500 HD, 3500 HD, Chassis Cab 2014-2014 Sierra / Sierra Denali New body style 2007-2007 Sierra / Sierra Denali New body style 2007-2007 Sierra / Sierra Denali New body style 2007-2007 Sierra / Sierra Denali 2008-2013 Sierra / Sierra Denali 2008-2013 Sierra / Sierra Denali 2008-2013 Yukon / Yukon XL / Yukon Denali 2007-2014 Rear Speaker Applications BUICK Envision 2016-2020 LaCrosse 2014-2019 CADILLAC CT6, CT6-V 2016-2020 CHEVEROLET Colorado Extended Cab 2015-2020 Silverado 1500 Crew Cab 2019-2023 Silverado 1500 Crew Cab 2014-2018 Silverado 1500 LD Crew Cab 2019-2019 Silverado 2500 HD, 3500 HD Crew Cab 2020-2023 Silverado 2500HD, 3500HD, Chassis Cab Crew Cab 2015-2019 Spark 2016-2020 Suburban 2015-2020 Traverse 2009-2012 GMC Canyon Extended Cab 2015-2020 Sierra / Sierra Denali 1500 Crew Cab 2019-2023 Sierra / Sierra Denali 1500 Extended Cab 2019-2023 Sierra / Sierra Denali 1500 Crew Cab 2014-2018 Sierra / Sierra Denali 1500 Limited Crew Cab 2019-2019 Sierra / Sierra Denali 2500 HD, 3500 HD, Chassis Cab Crew Cab 2015-2023 Yukon / Yukon XL / Yukon Denali 2021-2023 Yukon / Yukon XL / Yukon Denali 2015-2020 Yukon / Yukon XL / Yukon Denali 2007-2014

    2 Available for pickup

    $22.99

  • Metra 82-6600 : 5.25"-6.5" Door Speaker Replacement Trim Ring, 1995-UP Chrysler Dodge Jeep RAM

    Metra 82-6600 : 5.25"-6.5" Door Speaker Replacement Trim Ring, 1995-UP Chrysler Dodge Jeep RAM

    2 Available for pickup

    5-1/4" to 6-1/2" Door Speaker Replacement Trim Ring for Select 1995-UP Chrysler, Dodge, Jeep, Plymouth and RAM Vehicles Adapts 5 1/4 inch or 6 1/2 speaker to front door speaker location Sold as a pair Front Speaker Applications CHRYSLER 300M 1999-2004 Cirrus 1995-2000 Concorde 1998-2004 LHS 1999-2001 PT Cruiser 2006-2010 PT Cruiser 2001-2005 DODGE Dakota 2002-2004 Dakota 2001-2001 Dakota 1997-2000 Durango 2004-2007 Durango 2002-2003 Durango 2001-2001 Durango 1998-2000 Intrepid 1998-2004 Neon 2002-2006 Neon 2000-2001 Neon 1995-1999 JEEP Grand Cherokee 1997-1998 Grand Cherokee 1996-1996 PLYMOUTH Breeze 1996-1999 Neon 1995-1999 RAM ProMaster 2014-2020 Rear Speaker Application DODGE Durango 2021-2021 Durango 2014-2020 JEEP Grand Cherokee 2014-2020 Wrangler JK 2018-2018 Wrangler 2015-2017

    2 Available for pickup

    $19.99

  • Alpine S-S65 : 6.5" 80W RMS Coaxial Speakers

    Alpine S-S65 : 6.5" 80W RMS Coaxial Speakers

    Pre-Order Today!

    Alpine 6-1/2-Inch Coaxial 2-Way Speakers, 80-Watt RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specifications 80W RMS/240W Peak Nominal Impedance 4Ω Frequency Response: 70-22kHz 1” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround CustomStamped Steel Frame 35mm voice coil Optional grille sold separately (KTE-S65G)

    Pre-Order Today!

    $119.99

  • Metra 82-3002 : 5.25" to 6.5" Door Speaker Replacement Trim Ring, 1995-2010 Cadillac Chevy GMC

    Metra 82-3002 : 5.25" to 6.5" Door Speaker Replacement Trim Ring, 1995-2010 Cadillac Chevy GMC

    4 Available for pickup

    5.25"- 6.5" Speaker Adapter Trim Rings for Select 1995-2009 Buick, Cadillac, Chevy, GMC, Hummer, Oldsmobile, Pontiac and Saturn Vehicles Speaker Adapter Plates Adapts a 5.25in or 6.5in speaker to front door speaker location Sold as a pair Front Speaker Applications BUICK Terraza 2005-2007 CADILLAC Escalade, Escalade ESV, Escalade EXT 2003-2006 Escalade, Escalade EXT 1999-2002 CHEVEROLET Avalanche 2003-2006 Avalanche 2002-2002 C/K Pickup 1995-2000 Cobalt 2005-2010 Silverado old body style (Classic) 2007-2007 Silverado 2003-2006 Silverado 1999-2002 Suburban 2003-2006 Suburban 1995-2002 Tahoe 2007-2014 Tahoe 2003-2006 Tahoe 2000-2002 Tahoe 2 door 1995-1999 Tahoe 4 door 1995-1999 Uplander 2005-2008 Venture 2000-2005 Venture 1997-1999 GMC C/K Pickup 1995-1998 Savana 2003-2007 Sierra 2 door 1999-2002 Sierra 4 door 1999-2002 Sierra  Classic 2 door 1999-2000 Sierra  Classic 4 door 1999-2000 Sierra  Classic / Sierra Denali Classic 2 door 2007-2007 Sierra  Classic / Sierra Denali Classic 4 door 2007-2007 Sierra  HD 2 door 2001-2002 Sierra  HD 4 door 2001-2002 Sierra / Sierra Denali 2 door 2003-2006 Sierra / Sierra Denali 4 door 2003-2006 Suburban 1995-1999 Yukon / Yukon Denali 2 door 1995-1999 Yukon / Yukon Denali 4 door 1995-1999 Yukon / Yukon XL / Yukon Denali 2003-2006 Yukon / Yukon XL / Yukon Denali 2000-2002 HUMMER H2 2008-2009 H2 2003-2007 OLDSMOBILE Silhouette 2000-2004 Silhouette 1997-1999 PONTIAC Montana 1999-2005 Montana SV6 2005-2006 TransSport 1997-1999 SATURN Relay 2005-2007 Rear Speaker Applications CHEVEROLET Uplander 2005-2008 Venture 2000-2005 Venture 1997-1999 OLDSMOBILE Silhouette 2000-2004 Silhouette 1997-1999 PONTIAC Montana 1999-2005 Montana SV6 2005-2006 TransSport 1997-1999 SATURN Relay 2005-2007

    4 Available for pickup

    $16.99

  • Alpine S2-S65C : 6.5" 80W RMS Component Speakers Alpine S2-S65C : 6.5" 80W RMS Component Speakers, woofer top side.

    Alpine S2-S65C : 6.5" 80W RMS Component Speakers

    2 Available for pickup

    Alpine 6-1/2-Inch Component 2-Way Speakers, 80-Watt RMS Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65C 6.5” Component Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra- High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry- level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. Alpine-exclusive High Amplitude Multi- Roll (HAMR) surround technology is integrated into the speaker design which allows for maximum cone movement, delivering powerful and accurate bass notes. Engineered for versatility, these speakers offer seamless OEM fitment and simplified installation. With in-line crossovers, you can achieve optimal sound separation and precise tuning. The adjustable tweeters feature a flush mount housing that is removable allowing for installations in small OEM tweeter locations. The S-Series S2-S65 is compatible with the KTE-S65G Speaker Grille (sold separately). This sleek and stylish grille will not only add a visual upgrade to your speakers but also provide protection against any damage. Specifications Hi-Res Audio Certified (Up to 40kHz) Poly Propylene, Glass Fiber, and Mica Cone Material Lightweight Design with High Output and Low Distortion High-Amplitude Multi-Roll (H.A.M.R.) Surround   Included 1” Adjustable Tweeters with Threaded Removable Housing (Component) OEM Fitment with In-Line Crossovers Compatible with KTE-S65G Speaker Grille (sold separately) Woofer Size: 6.5”  Tweeter Size: 1” (Component) Power Handling: 80W RMS / 240W Peak Frequency Response: 70Hz - 40kHz (Hi-Res) Sensitivity: 88dB

    2 Available for pickup

    $149.99

  • Metra 82-5605 : 6.5" Speaker Replacement Trim Ring, 2021-UP Ford Bronco

    Metra 82-5605 : 6.5" Speaker Replacement Trim Ring, 2021-UP Ford

    2 Available for pickup

    6.5-Inch Kick-Panel-Speaker Replacement Trim-Ring Adapter for Select 2021-UP Ford Bronco Vehicles Upgrade your Ford Bronco’s kick panel speakers with the help of these adapter plates. These plates are sold as a pair and are designed for installation of the 6.5” to 6.75” speakers. They mount directly into the factory location so there is no drilling required and feature a breakaway tab design for easy installation. For the installation of 6.5” – 6.75” kick panel speakers Breakaway tab design Sold as a pair Front Speaker Applications FORD Bronco (full size), Bronco Sport 2021-2023 Maverick 2021-2022 Bronco, Bronco Sport 2021-2023 EcoSport 2018-2020 Edge 2015-2019 Escape 2013-2022 Focus 2015-2018 Focus 2012-2014 Fusion 2013-2020 Mustang 2015-2020 Transit 2015-2019 HYUNDAI Venue 2020-2020 LINCOLN MKX 2016-2018 Rear Speaker Applications FORD Bronco, Bronco Sport 2021-2023 EcoSport 2018-2020 Edge 2015-2019 Escape 2013-2022 Explorer 2011-2019 F-150 2015-2022 F-250 / F-350 / F-450 / F-550 2017-2020 Focus 2015-2018 Focus 2012-2014 Fusion 2013-2020 Mustang 2015-2020 Transit Connect 2014-2021 HYUNDAI Venue 2020-2020 LINCOLN MKX 2016-2018

    2 Available for pickup

    $19.99

  • Kicker 47KSS6504 : 6.5-Inch 125-Watt Component or Coaxial Mountable Speaker System. Kicker 47KSS6504 : 6.5-Inch 125-Watt Component or Coaxial Mountable Speaker System contents.

    Kicker 47KSS6504 : 125W 6.5" Convertible Component Speakers

    2 Available for pickup

    6.5-Inch 125-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 6.5" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 125 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 6-½, 160 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-125 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 35-21k Woofer Mounting Hole Diameter [in, mm] 4-13⁄16 , 123 Woofer Bottom Mount Depth [in, mm] 1-13⁄16 , 46 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

    2 Available for pickup

    $249.99

  • Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers, front side.

    Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers

    3 Available for pickup

    Alpine 6-1/2-Inch Coaxial 2-Way Speakers, 80-Watt RMS Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry-level price point.  Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. Alpine-exclusive High Amplitude Multi- Roll (HAMR) surround technology is integrated into the speaker design which allows for maximum cone movement, delivering powerful and accurate bass notes. The S-Series S2-S65 is compatible with the KTE-S65G Speaker Grille (sold separately). This sleek and stylish grille will not only add a visual upgrade to your speakers but also provide protection against any damage. Specifications Hi-Res Audio Certified (Up to 40kHz) Poly Propylene, Glass Fiber, and Mica Cone Material Lightweight Design with High Output and Low Distortion High-Amplitude Multi-Roll (H.A.M.R.) Surround   Integrated 1” Tweeters (Coaxial) Compatible with KTE-S65G Speaker Grille (sold separately) Woofer Size: 6.5”  Tweeter Size: 1” (Coaxial) Power Handling: 80W RMS / 240W Peak Frequency Response: 70Hz - 40kHz (Hi-Res) Sensitivity: 88dB

    3 Available for pickup

    $129.99

  • Last One! Metra 82-8153 : 6"-6.75" Door Speaker Replacement Trim Ring, 2001-2007 Toyota

    Metra 82-8153 : 6"-6.75" Door Speaker Replacement Trim Ring, 2001-2007 Toyota

    1 Available for pickup

    Replacement Six-Inch to 6-3/4-Inch Door Speaker Trim Ring Adapter for Select 2001-2007 Toyota Vehicles Mounting adapter For 6-6.75 inch speakers Front door location Sold as a pair Applications TOYOTA Sequoia 2003-2007 Sequoia 2001-2002 Tundra w/o JBL crew cab 2004-2006

    1 Available for pickup

    $21.99

  • Alpine R2-S653 : 6.5" PRO 3-Way Component Door Speaker System, 100W RMS Alpine R2-S653 : 6.5" PRO 3-Way Component Door Speaker System, woofer mid and tweeter.

    Alpine R2-S653 : 6.5" PRO 3-Way Component Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The Next-Generation R-Series speakers now come in upgraded 'Pro' models in addition to the standard model lineup. The pro models utilize a highly rigid, die-cast aluminum basket that eliminates flexing and resonance during playback to ensure the highest quality sound performance. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65C is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $599.99

  • Alpine R2-S65C : 6.5" Component Door Speaker System, 100W RMS Alpine R2-S65C : 6.5" Component Door Speaker System, woofer and tweeter.

    Alpine R2-S65C : 6.5" Component Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65C is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade In-Line Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $349.99

  • Metra 82-5607 : 6.5" Door Speaker Replacement Trim Ring, 2015-UP Ford F-Series

    Metra 82-5607 : 6.5" Door Speaker Replacement Trim Ring, 2015-UP Ford F-Series

    3 Available for pickup

    6.5" Replacement Speaker Adapter Plate for 2015-UP Ford F-Series Vehicles Accommodates 6 to 6.75 inch speaker Will work front door speaker locations Packaged as a pair Front Speaker Applications FORD F-150 2015-2022 F-250 / F-350 / F-450 / F-550 2017-2020

    3 Available for pickup

    $24.99

  • JL Audio C2-650 : 6.5" Component Speakers - 60W RMS JL Audio C2-650 : 6.5" Component Speaker woofer.

    JL Audio C2-650 : 6.5" Component Speakers, 60W RMS

    2 Available for pickup

    C2-Series 6.5-Inch Component Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs. The C2-650 system features 6.5-inch (165 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-650 Manual

    2 Available for pickup

    $299.99

  • JL Audio C2-650x : 6.5" Coaxial Speakers - 60W RMS JL Audio C2-650x : 6.5" Coaxial Speaker front side.

    JL Audio C2-650x : 6.5" Coaxial Speakers, 60W RMS

    4 Available for pickup

    C2-Series 6.5-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-650x system features 6.5-inch (165 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-650x Manual

    4 Available for pickup

    $249.99

  • Metra 82-8901 : 5.25" Speaker Replacement Trim Ring, 2015-2020 Subaru WRX

    Metra 82-8901 : 5.25" Speaker Replacement Trim Ring, 2015-2020 Subaru WRX

    3 Available for pickup

    6.5-Inch to 6.75-Inch Door-Speaker Replacement Trim-Ring Adapter for Select 2015-2020 Subaru WRX Vehicles Allows installation of aftermarket 6.5 to 6 3/4 inch speakers in the front doors Includes one pair of adapters Front Speaker Applications SUBARU WRX, WRX STI 2016-2020

    3 Available for pickup

    $22.99

  • Last One! Metra JP-1015 : 6.5" Speaker Replacement Adapter Plate, 2018-UP Jeep Wrangler Gladiator JL/JT. Metra JP-1015 : 6.5" Speaker Replacement Adapter Plate, shown installed.

    Metra JP-1015 : 6.5" Speaker Replacement Adapter Plate, 2018-UP Jeep Wrangler Gladiator JL/JT

    1 Available for pickup

    Aftermarket Sound-Bar-Speaker Replacement Adapter-Plates for Select 2018-Up Jeep Wrangler and 2020-Up Gladiator JL & JT Vehicles Don't limit your speaker upgrade to the size of the 4" factory speakers. Go bigger with the JP-1015, designed to fit a larger 6.5" aftermarket speaker and optional tweeter into the factory soundbar location. Designed to adapt the factory 4” to 6.5” with a tweeter option Speaker depth 3 5/8" Mounting plate/cutting template included Hardware included Harness included The sound bar must be removed for installation - add 1hr to install time. Dome light clips are stronger than the plastic they are attached to. Dome light clip mounts may break off during removal, JTAS does not carry liability associated with the dome light and customer accepts liability for dome light replacement should breakage occur. Kit Includes: (2) grille replacements (2) cutting template/grille support (8) speaker mounting screws (12) grille replacement screws (2) cutting template/grille support screws (2) 7” speaker harnesses (2) sound deadening padding Metra JP-1015 Installation Manual

    1 Available for pickup

    $134.99

  • Last One! Metra JP-1014 : 6"- 6.75" Speaker Replacement Adapter Pods, 2018-Up Wrangler Gladiator JL Metra JP-1014 : 6"- 6.75" Speaker Replacement Adapter Pods, rear view.

    Metra JP-1014 : 6"- 6.75" Speaker Replacement Adapter Pods, 2018-Up Wrangler Gladiator JL/JT

    1 Available for pickup

    Aftermarket Dash-Speaker Replacement Enclosure Pods  for Select 2018-Up Jeep Wrangler and 2020-Up Gladiator JL & JT Vehicles Each pair of pods has an ABS housing that utilizes the factory mounting locations for a secure fit that will heighten the listening experience. The pods use the factory grommet and wiring and a Metra speaker adapter harness is included. Driver and passenger specific dash replacement sealed speaker pods to install 6in to 6.75in speaker Mounting positions for Chrysler three hole mount used by specific speaker manufacturers such as Alpine Sealed enclosure (1) with a hole for the factory wiring grommet 4-inch speaker depth Includes 12" speaker harness Significant disassembly of the Dash is required to access these speaker pod locations. Add 2-hours to installation time. Metra JP-1014 Installation Manual

    1 Available for pickup

    $59.99

  • Alpine PSS-24WRA : 300W Replacement Speaker and Subwoofer Upgrade Package, 2018-UP Wrangler, GladiatorAlpine PSS-24WRA : 300W Replacement Speaker and Subwoofer Upgrade Package, 2018-UP Wrangler JL, Gladiator JT

    Alpine PSS-24WRA : 300W Replacement Speaker and Subwoofer Upgrade Package, 2018-UP Wrangler JL, Gladiator JT

    Pre-Order Today!

    300-Watt Door-Speaker and Add-On Subwoofer Kit for Select 2018-UP Jeep Wrangler-JL and Gladiator-JT Vehicles The PSS-24WRA is a 300-Watt Complete Sound System Upgrade Package for the four-door, non-amplified 2018–Up Jeep Wrangler-JL and non-amplified 2020–Up Jeep Gladiator-JT. Go beyond your wildest expectations for sound with this complete sound upgrade package. The PSS-24WRA has 5-channels of powered sound that replaces your factory system. The package includes two sets of 6.5” weather-resistant mid-bas drivers and 1” weather-resist tweeters that replace the front and rear soundbar factory speakers, an 8” powered, compact subwoofer and a 4-channel power pack amplifier. Specifications Complete, five-channel powered sound system upgrade package   Compatible with four-door, non-amplified 2018 - Up Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator Also compatible with two-door, non-scissor front seats in 2019 - Up Jeep® Wrangler Includes Alpine’s SPV-65X-WRA, SPV-65-JLT, PWE-S8, and KTP-445U  180W, 4-channel Power Pack amplifier  120W, 8” powered subwoofer  (2x) 6.5” weather-resistant mid-bass drivers  (2x) 1” weather-resistant teteron dome tweeters with vehicle-specific connectors and crossovers  Vehicle specific front speaker pods with vehicle-specific connectors  Tweeter adapter plates allow for use of the original factory tweeter locations  SPV-65-JLT weather-resistant rear soundbar speaker system Rugged, premium grills designed to emulate the factory look and appeal   Vehicle-specific connectors for plug-and-play speaker installation   Utilizes factory bolt locations   Durable stamped, steel frame speaker basket design  Includes template for mounting Vehicle specific T-harness for installation with OEM radio into compatible 2018 – Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator vehicles  Vehicle specific mounting brackets allow for the powered sub and amp to be secured under the passenger seat without drilling  What's in the Box: KTP-445U Universal 4-Channel Power Amplifier  PWE-S8 8" Compact Powered Subwoofer  SPV-65X-WRA Front Component Speakers SPV-65-JLT Rear Sound Bar Speakers ALP-POD-JLT Front Speaker Pod PSU-BKT-JL-R PWE Right Bracket JL PSU-BKT-JL-L PWE Left Bracket JL ALP-HRN-PSU300 PSU Power Harness  ALP-THRN-CH2 Chrysler T-Harness  CT6 6" Cable Ties PHPSM412 Pan Head Phillips Screw M4x12 SLWM4 M4 Split Lock Washers PHSCR832 8-32 Pan Head Phillips screws PSS-WRA-IM Installation Manual Specifications Front (SPV-65X-WRA) Power handling: 75 watts RMS (225 watts peak)  Frequency response: 65kHz – 22kHz  Nominal impedance: 4 ohms  Weather-resistant: IP55   Rear (SPV-65-JLT) Power handling: 90 watts RMS (270 watts peak)  Frequency response: 50kHz – 22kHz  Nominal impedance: 4 ohms  Weather-resistant: IP55 Powered Subwoofer (PWE-S8) 120 watts RMS (240 watts peak)  Frequency response: 32 - 150Hz  Variable low-pass crossover (80-200 Hz)  Variable phase control (0-180 degrees)  preamp- and speaker-level inputs  Four Channel Power Pack Amplifier (KTP-445U) 45 watts RMS x 4 at 4 or 2 ohms  90 watts RMS x 2 bridged at 4 ohms  Selectable high-pass filters (60, 80, or 120 Hz at 12 dB/octave)  Switchable RCA or speaker-level inputs| Dimensions:  27” L x 18.5” W x 19.5” H 40lbs Direct fit for non-amplified 2018–Up 4-door Jeep Wrangler JL Unlimited Direct fit for non-amplified 2019–Up 2-door Jeep Wrangler Direct fit for non-amplified 2020–Up Jeep Gladiator JT Alpine PSS-24WRA Installation Manual

    Pre-Order Today!

    $1,999.99

  • Metra 82-8147 : 6"-6.75" Door Speaker Replacement Trim Ring, 2002-UP Lexus Subaru Toyota

    Metra 82-8147 : 6"-6.75" Door Speaker Replacement Trim Ring, 2002-UP Lexus Subaru Toyota

    4 Available for pickup

    Six-Inch to 6-3/4-Inch Door Speaker Trim Ring Adapter for Select 2002-UP Lexus, Subaru and Toyota Vehicles Accommodates 6 to 6.75 inch speaker – pair Front Speaker Applications LEXUS CT 200h 2011-2013 GX Series 2010-2014 GX Series 2003-2009 LS 460 2010-2012 LS 460 2007-2009 LS 600h L 2013-2014 LS 600h L 2010-2012 LS 600h L 2008-2009 LS Series 2013-2014 SUBARU Crosstrek 2018-2020 Impreza 2017-2020 Legacy 2015-2020 Outback 2018-2018 TOYOTA (Camry) Solara 2004-2008 4Runner 2015-2020 4Runner 2010-2014 4Runner 2003-2009 Avalon 2013-2014 Avalon 2011-2012 Avalon 2005-2010 Camry w/o JBL 2002-2011 FJ Cruiser 2007-2014 Highlander 2008-2012 Land Cruiser 2008-2014 Prius 2012-2015 Prius 2010-2011 Sequoia 2008-2014 Tacoma 2005-2015 Tundra 2014-2018 Tundra crew cab 2007-2013 Venza 2009-2015

    4 Available for pickup

    $23.99

  • Metra 82-7805 : 6"-6.75" Door Speaker Replacement Trim Ring, 2006-UP Acura Honda

    Metra 82-7805 : 6"-6.75" Door Speaker Replacement Trim Ring, 2006-UP Acura Honda

    3 Available for pickup

    Replacement Six-Inch to 6-3/4" Door-Speaker Trim-Ring Adapter for Select 2006-UP Acura and Honda Vehicles Accommodates 6” to 6.75” speaker – pair Front Speaker Applications ACURA TL 2009-2014 HONDA Accord 2018-2020 Accord 2013-2017 Accord 2008-2012 Accord Crosstour 2010-2011 Civic Coupe, Sedan 2016-2020 Civic Hatchback 2017-2020 Civic 2012-2015 Civic 2006-2011 CR-V 2017-2020 Insight 2019-2020 Pilot 2016-2022 Rear Speaker Applications ACURA TL 2009-2014 HONDA Accord 2013-2017 Accord 2008-2012 Accord Crosstour 2010-2011 Civic Coupe, Sedan 2016-2020 CR-V 2017-2020 Insight 2019-2020 Pilot 2016-2022

    3 Available for pickup

    $20.99

  • Metra 82-4401 : Universal 6-6 3/4" Door Speaker Replacement Trim Ring, 1/2" Rise

    Metra 82-4401 : Universal 6-6 3/4" Door Speaker Replacement Trim Ring, 1/2" Rise

    3 Available for pickup

    Universal 1/2-Inch Thick Replacement Speaker Trim Ring for 6-inch to 6.75-Inch Drivers 1/2 inch spacer designed for installation of 6 to 6-3/4 inch aftermarket speakers & works with all varieties of speakers including component drivers One pair of adapters included in each package

    3 Available for pickup

    $18.99

  • Morel Hybrid Integra 62 : 6.5" Coaxial Door Speakers, 100W RMS

    Morel Hybrid Integra 62 : 6.5" Coaxial Door Speakers, 100W RMS

    Pre-Order Today!

    Hybrid Integra Series 6-1/2" 100-Watt RMS 2-Way Coaxial Door Speakers Embracing Morel’s legendary craftsmanship, engineering, and innovation, the latest Hybrid systems define an ever-evolving concept of high-fidelity speaker design. Now in their fifth generation, the new Hybrid and Hybrid Integra systems give a further refined listening experience, captivating you with the raw emotions of listening to live music. Their subtle balance of resolution, power, and efficiency has been further optimized to exceed expectations regardless of what genre of music you enjoy.   The Integra, Morel’s point source system, is an innovative landmark in speaker design. It utilizes point-source topology to eliminate acoustic problems inherent in conventional coaxial systems. By creating a single sound source on the same axis, the tweeter and woofer seamlessly integrate, generating Omni-directional time alignment, heightened imaging, and sound dispersion. Now the Hybrid is available in 2-way and Integra point source (coaxial) solutions, as well as a new 3-way system to fit nearly any system requirement. CONTROLLED ACOUSTIC RESISTANCEThe C.A.R. Filter™ improves the acoustic loading by controlling airflow within the driver, mimicking the effects of a cabinet while improving power handling by 30%. This provides greater control over the cone movement for improved bass dynamics. EVC MOTORMorel speakers with EVC™ technology utilize voice coils that are up to three times larger than those used in conventional loudspeakers, enabling improved heat dissipation, power handling and linearity. The EVC™ design moves the magnetic motor system to within the voice coil, eliminating stray magnetic flux by effectively directing all the magnetic energy to the voice coil. The EVC architecture is over 90% more efficient than conventional design, magnetically shielded, and highly compact. HEXATECH™ ALUMINIUM VOICE COILMade from 100% aluminum wire shaped like a honeycomb, the Hexatech™ voice coil reduces air gaps in the coil windings, thereby increasing efficiency by up to 20%. Being lightweight, Hexatech™ voice coils are largely responsible for the extraordinary fast transient response Morel drive units are known for. HYBRID MAGNET MOTORThe Hybrid motor drive system uses a ferrite magnet together with a very powerful neodymium magnet. Combined they create a compact, lightweight motor system that is up to four times more powerful than conventional designs of the same size. With Hybrid, more amplified power is converted into sonic energy for flawless performance, even in a small driver. INTEGRADerived from the word “integrate”, Integra is a speaker consisting of both a woofer and tweeter that share a common chassis. Unlike a coaxial, its recessed tweeter is concentrically aligned with the woofer cone. This minimizes phase error and allows the sound field to be constant in all directions, creating a near-perfect time alignment. PAPER CONEIn use since the first loudspeakers, the paper continues to be an exceptional material of choice. Morel’s latest paper composite cones are ultra-lightweight, making them an exceptional pairing for drivers using smaller motors and voice coils. Sold by the Pair Specifications  MODEL SIZE & CONFIGURATION POWER HANDLING (WRMS) / PEAK POWER (W) SENSITIITY (2.83V/1M)(DB) FREQUENCY RESPONSE (HZ) CROSSOVER HYBRID INTEGRA 42 4" 2-way 80 /250 92 80-25000 MXR250.4i HYBRID INTEGRA 52 5¼" 2-way 120 / 500 90 45-25000 MXR250.4i HYBRID INTEGRA 62 6½" 2-way 140 / 600 91 35-25000 MXR250.4i Morel Hybrid Integra Series Door Speaker Manual

    Pre-Order Today!

    $799.99

  • Morel Hybrid 62 : 6.5" 2-Way Component Door Speakers, 140W RMS

    Morel Hybrid 62 : 6.5" 2-Way Component Door Speakers, 140W RMS

    Pre-Order Today!

    Hybrid Series 6-1/2" 140-Watt RMS 2-Way Component Door Speakers Embracing Morel’s legendary craftsmanship, engineering, and innovation, the latest Hybrid systems define an ever-evolving concept of high-fidelity speaker design. Now in their fifth generation, the new Hybrid and Hybrid Integra systems give a further refined listening experience, captivating you with the raw emotions of listening to live music. Their subtle balance of resolution, power, and efficiency has been further optimized to exceed expectations regardless of what genre of music you enjoy. Now the Hybrid is available in 2-way and Integra point source (coaxial) solutions, as well as a new 3-way system to fit nearly any system requirement.  CONTROLLED ACOUSTIC RESISTANCEThe C.A.R. Filter™ improves the acoustic loading by controlling airflow within the driver, mimicking the effects of a cabinet while improving power handling by 30%. This provides greater control over the cone movement for improved bass dynamics. EVC MOTORMorel speakers with EVC™ technology utilize voice coils that are up to three times larger than those used in conventional loudspeakers, enabling improved heat dissipation, power handling and linearity. The EVC™ design moves the magnetic motor system to within the voice coil, eliminating stray magnetic flux by effectively directing all the magnetic energy to the voice coil. The EVC architecture is over 90% more efficient than conventional design, magnetically shielded, and highly compact. HANDCRAFTED ACUFLEX SOFT DOMEA specially engineered damping compound hand-applied to the soft domes, adding rigidity and damping, which greatly improves the clarity and bandwidth of the tweeter/mid-range. The Acuflex™ diaphragm exhibits controlled cancelling break up (accurate–flexing), meaning each break-up mode is counteracted by another in the opposite direction, enabling smooth frequency response. HEXATECH™ ALUMINIUM VOICE COILMade from 100% aluminum wire shaped like a honeycomb, the Hexatech™ voice coil reduces air gaps in the coil windings, thereby increasing efficiency by up to 20%. Being lightweight, Hexatech™ voice coils are largely responsible for the extraordinary fast transient response Morel drive units are known for. HYBRID MAGNET MOTORThe Hybrid motor drive system uses a ferrite magnet together with a very powerful neodymium magnet. Combined they create a compact, lightweight motor system that is up to four times more powerful than conventional designs of the same size. With Hybrid, more amplified power is converted into sonic energy for flawless performance, even in a small driver. PAPER CONEIn use since the first loudspeakers, the paper continues to be an exceptional material of choice. Morel’s latest paper composite cones are ultra-lightweight, making them an exceptional pairing for drivers using smaller motors and voice coils. Sold by the Pair Specifications MODEL SIZE & CONFIGURATION POWER HANDLING (WRMS) / PEAK POWER (W) SENSITIITY (2.83V/1M)(DB) FREQUENCY RESPONSE (HZ) CROSSOVER HYBRID 42 4" 2-way 100 / 300 89 50-25000 MXR240.4 HYBIRD 52 5¼" 2-way 120 / 500 90 45-25000 MXR240.4 HYBRID 62 6½" 2-way 140 / 600 91 35-25000 MXR240.4 Morel Hybrid Series Door Speaker Manual

    Pre-Order Today!

    $999.99

  • Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, Dual Voice Coil Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, side view.

    Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, Dual Voice Coil

    Pre-Order Today!

    EVL Series 6-1/2-Inch 200-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil The Skar Audio EVL-65 D2 subwoofer was designed to be the most responsive, powerful, and efficient 6.5 inch subwoofer on the market. Don't be fooled by the size, the EVL-65 is one monster of a subwoofer, featuring a 4-layer 2" pure copper voice coil, and a powerful 39 Oz single slug ferrite motor. The small size of this driver allows it to be very versatile, as it can be used in a variety of applications where adding a woofer might not otherwise be possible. Conservatively rated at 200 watts RMS Power, and 400 watts max power, the EVL-65 features an aluminum diecast chassis which utilizes an advanced air flow cooling system to help dissipate heat. The suspension design of this subwoofer is highlighted by its unique yellow spider - which connects to the coil former with premium stitched lead wires. All of these incredible features make the EVL-65 the obvious choice when looking for a versatile 6.5-inch car subwoofer. Specifications Size 6.5" Type Car Subwoofer Cone Type Competition Grade Pressed Paper Cone RMS Power 200 Watts Peak Power 400 Watts Surround Type High Roll Rubber Surround Voice Coil Size 2.00" Magnet Slug Count Single Voice Coil Layers 4 Voice Coil Material Black Coated Copper (Pure Copper) Voice Coil Impedance Dual 2 Ω T/S Parameters Bl 13.0 n/a Fs 61.0 Hz Re Dual 2 Ω Sd 113.0 cm2 Cms 0.126 mm/N Mms 52.8 gr Qes 0.43 Qms 4.48 Qts 0.39 Vas 2.3 L Nref 0.12% Xmax 6.25 mm (one-way) Sensitvity 83.1 dB

    Pre-Order Today!

    $109.99

  • Metra 82-8140 : 6"-6.5" Door Speaker Replacement Trim Ring, 1995-2004 Tacoma Metra 82-8140 : 6"-6.5" Door Speaker Replacement Trim Ring, 1995-2004 Tacoma, side view.

    Metra 82-8140 : 6"-6.5" Front Door Speaker Replacement Trim Ring, 1995-2004 Tacoma

    2 Available for pickup

    Replacement Six-Inch to 6-1/2-Inch Front-Door Speaker Trim-Ring Adapter for Select 1995-2004 Toyota Tacoma Vehicles Provides spacing for aftermarket speaker installation. Works with all varieties of speakers including component drivers Accommodates 6" to 6.5" speaker – pair Front Speaker Applications TOYOTA Tacoma Double Cab / Extra Cab 2002-2004 Tacoma Regular Cab 2002-2004 Tacoma 1995-2001

    2 Available for pickup

    $25.99

  • JL Audio C3-650cw : C3 6.5" Component Woofer, side view. JL Audio C3-650cw : C3 6.5" Component Woofer, 75W RMS

    JL Audio C3-650cw : C3 6.5" Component Woofer, 75W RMS

    Pre-Order Today!

    C3-Series 6.5-Inch 75-Watt Component Woofer with Grille There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650cw is a 6.5-inch (165 mm) component woofer with an oversized 1.2-inch (30.5 mm) voice coil, mineral-filled polypropylene cone and injection-molded polymer basket. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. A woofer grille is included, consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold individually. Includes Component Phase Plug and Tweeter Post (Tweeter sold separately). General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 150 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 6 KHz ± 3 dB Physical Specifications Frame Outer Diameter (A) 6.50 in / 165 mm Grille Tray Outer Diameter (B) 6.74 in / 171 mm Motor Outer Diameter (C) 4.08 in / 104 mm Frontal Coaxial Tweeter Protrusion* (D) 0.75 in / 19 mm Frontal Grille Protrusion** (E) 1.03 in / 26 mm Mounting Hole Diameter (F) 5.56 in / 141 mm Mounting Depth (G) 2.55 in / 65 mm JL Audio C3-650cw Manual

    Pre-Order Today!

    $179.99

  • Metra 82-6601 : 6"-6.75" Door Speaker Replacement Trim Ring, 1995-UP Chrysler Dodge Jeep

    Metra 82-6601 : 6"-6.75" Door Speaker Replacement Trim Ring, 1995-UP Chrysler Dodge Jeep

    2 Available for pickup

    6" to 6-3/4" Door Speaker Replacement Trim Ring for Select 1995-UP Chrysler, Dodge, Jeep, Plymouth and RAM Vehicles Adapts 6 inch or 6.75 Inch speaker to front door speaker location Sold as a pair Front Speaker Applications CHRYSLER 300M 1999-2004 Cirrus 1995-2000 Concorde 1998-2004 LHS 1999-2001 PT Cruiser 2006-2010 PT Cruiser 2001-2005 DODGE Dakota 2002-2004 Dakota 2001-2001 Dakota 1997-2000 Durango 2004-2007 Durango 2002-2003 Durango 2001-2001 Durango 1998-2000 Intrepid 1998-2004 Neon 2002-2006 Neon 2000-2001 Neon 1995-1999 Nitro 2007-2011 JEEP Grand Cherokee 1997-1998 Grand Cherokee 1996-1996 Liberty 2002-2012 Wrangler JK 2018 Wrangler 2007-2017 PLYMOUTH Breeze 1996-1999 Neon 1995-1999 RAM ProMaster 2014-2020 Rear Speaker Applications DODGE Durango 2021-2021 Durango 2014-2020 Nitro 2007-2011 JEEP Grand Cherokee 2014-2020 Liberty 2002-2012 Wrangler JK 2018-2018 Wrangler 2015-2017 Wrangler 2007-2014

    2 Available for pickup

    $22.99

  • Alpine R2-S652 : 6.5" PRO Component Door Speaker System, 100W RMS Alpine R2-S652 : 6.5" PRO Component Door Speaker System, woofer and tweeter.

    Alpine R2-S652 : 6.5" PRO Component Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The Next-Generation R-Series speakers now come in upgraded 'Pro' models in addition to the standard model lineup. The pro models utilize a highly rigid, die-cast aluminum basket that eliminates flexing and resonance during playback to ensure the highest quality sound performance. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S652 is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with an outboard crossover network the professional installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $399.99

  • Alpine R2-S65 : 6.5" Coaxial Door Speaker System, 100W RMS Alpine R2-S65 : 6.5" Coaxial Door Speaker System, woofer.

    Alpine R2-S65 : 6.5" Coaxial Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65 is a standard coaxial speaker set that includes a 6.5” Mid-Range and 1” Coaxial Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $249.99

  • Alpine HDZ-653S : 6.5" 3-Way Slim-Fit Component Door Speakers, 100W RMS Alpine HDZ-653S : 6.5" 3-Way Slim-Fit Component Door Speakers, woofers.

    Alpine HDZ-653S : 6.5" 3-Way Slim-Fit Component Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-653S features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-653S has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-653S is a custom-fit model that includes a 6.5- inch Mid-Bass driver, a 3.5-inch Midrange driver, and 1.25-inch High-Range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 3.5" Midrange Driver (8.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-653S Manual

    Pre-Order Today!

    $999.99

  • Alpine HDZ-653 : 6.5" 3-Way Component Door Speakers, 100W RMS Alpine HDZ-653 : 6.5" 3-Way Component Door Speakers, woofers.

    Alpine HDZ-653 : 6.5" 3-Way Component Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-653 features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-653 has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-653 is a custom-fit model that includes a 6.5- inch Mid-Bass driver, a 3.5-inch Midrange driver, and 1.25-inch High-Range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 3.5" Midrange Driver (8.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-653 Manual

    Pre-Order Today!

    $999.99

  • Alpine HDZ-65CS : 6.5" Slim-Fit Component Door Speakers, 100W RMS Alpine HDZ-65CS : 6.5" Slim-Fit Component Door Speakers, woofers.

    Alpine HDZ-65CS : 6.5" Slim-Fit Component Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65CS features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65CS has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65CS is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65CS Manual

    Pre-Order Today!

    $749.99

  • Alpine HDZ-65C : 6.5" Component Door Speakers, 100W RMS Alpine HDZ-65C : 6.5" Component Door Speakers, tweeters.

    Alpine HDZ-65C : 6.5" Component Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65C features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65C has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65C is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is soldseparately and can be used to build acustom sound system. Three sets of true4V preamp outputs are included to add needed. For best results, install the additional amplifiers if more power iscomplete Alpine Status system togetheras a full system to achieve the highestin-class audio performance only second to the Ultra Hi-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65C Manual

    Pre-Order Today!

    $749.99

  • Alpine HDZ-65 : 6.5" Coaxial Door Speakers, 100W RMS Alpine HDZ-65 : 6.5" Coaxial Door Speakers, top side view.

    Alpine HDZ-65 : 6.5" Coaxial Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest- quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65 features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65 has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65 is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1” Coaxial Tweeter (2.5cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65 Manual

    Pre-Order Today!

    $549.99

  • Metra 82-3005 : 6-6.75" Door Speaker Replacement Trim Ring, 2015-UP Chevy GMC

    Metra 82-3005 : 6-6.75" Door Speaker Replacement Trim Ring, 2015-UP Chevy GMC

    2 Available for pickup

    Six-Inch to Six-3/4" Door-Speaker Replacement Adapter-Plates for Select 2015-UP Chevy and GMC Vehicles Vehicle specific spacer designed for installation of 6 to 6.75 inch aftermarket speakers Will work: front door speaker locations (Sierra/Silverado) rear deck (Malibu) One pair of adapters included in each package Front Speaker Applications CHEVEROLET Blazer 2019-2020 Silverado Crew Cab - 1500 2019-2023 Silverado Crew Cab - 2500 HD, 3500 HD 2020-2023 GMC Sierra / Sierra Denali Crew Cab - 1500 2019-2023 Sierra / Sierra Denali Extended Cab - 1500 2019-2023 Sierra / Sierra Denali Standard Cab - 1500 2019-2023 Sierra / Sierra Denali Crew Cab - 2500 HD, 3500 HD, Chassis Cab 2015-2023 Rear Speaker Applications CHEVEROLET Malibu 2016-2020

    2 Available for pickup

    $19.99

  • Metra 82-7803 : 5.25-6.5" Door Speaker Replacement Trim Rings, 1993-2015 Honda Volkswagen

    Metra 82-7803 : 5.25-6.5" Door Speaker Replacement Trim Rings, 1993-2015 Honda Volkswagen

    2 Available for pickup

    6-1/2" or 5-1/4-Inch Door-Speaker Adapter Plates for Select Acura, Honda and Volkswagen Vehicles 5.25” and 6.5” speaker adapter plates One pair of adapters included in each package Front Speaker Applications ACURA CL 1997-2003 HONDA Accord 1998-2002 Accord 2003-2007 Civic Coupe, Sedan 2001-2005 Civic Hatchback 2002-2005 VOLKSWAGEN Beetle 1998-2010 Golf 2012-2014 Golf 1999-2011 Golf 1994-1998 Golf R 2012-2013 GTI 2006-2014 GTI 1998-2005 GTI 1995-1997 Jetta w/ SDIN radio 2002-2002 Jetta 1999-2001 Jetta 1993-1998 Jetta, Jetta GLI w/ DDIN radio 2002-2002 Jetta, Jetta GLI 2003-2015 Passat 2006-2015 Passat 1998-2005

    2 Available for pickup

    $15.99

  • 90W 6.5" Component Speakers, Coaxial Convertible : Kicker 41QSS654 90W 6.5" Component Speakers, Coaxial Convertible : Kicker 41QSS654, woofer.

    Kicker 41QSS654 : 90W 6.5" Component Speakers, Coaxial Convertible

    Pre-Order Today!

    6.5-Inch 90-Watt RMS Convertible Component Automotive Door Speakers The 6.5" QS series audiophile component door speakers by Kicker offer stunning midrange drivers, audiophile precise tweeters and a superior crossover network. The QS 6-1/2 Inch convertible speakers are a matched component system, built for pure sonic reproduction.  The Kicker 41QSS654 crossovers allow you to use a single amplifier channel, or use bi-amplification for even more flexibility and control. These 6.5" QS series convertible speakers can be installed as a pair of components or a coaxial configuration. These Kicker speakers work best with 90 watts of recommended power. See below for more details. Specifications Woofer (in., mm) 6 1/2, 160 Tweeter (in., mm) 1 3/16, 30 Tweeter dome material Tetoron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 90 Peak Power (watts, per ANSI/CTA-2031-A) 180 Sensitivity [1W, 1m] 86dB Frequency Response [Hz] 50 - 22k Woofer Mounting Hole Diameter [in, mm] 5 1/16, 129 Woofer Bottom Mount Depth [in, mm] 2 1/2, 63.5 Flush Mount Tweeter Hole Diameter [in,mm] 1 13/16, 46 Flush Mount Tweeter Depth [in,mm] 1 1/8, 29 High Pass [dB], at Frequency [Hz] 24, 2800 Low Pass [dB], at Frequency [Hz] 12, 2800 High Frequency Output Attenuation [dB] 0, +3, +6 Kicker QSS Series Manual

    Pre-Order Today!

    $599.99

  • Kicker 46CSS654 : 100-Watt Component Speakers Six-1/2" Drivers 6.5" 100W Component Speaker System : Kicker 46CSS654 woofer.

    Kicker 46CSS654 : 100W 6.5" Component Speaker System

    Pre-Order Today!

    100-Watt Component Speakers Six-1/2" Drivers The CS Series 6-1/2-inch component speakers by Kicker are designed for easy installation in nearly any vehicle. These components include separate titanium flush, angled or surface-mount tweeters and two-way crossovers with tweeter level control to let you customize your sound for the best sonic quality. The Kicker CS Series 6-1/2" speakers work best with up to 100-watts of recommended power. Specifications Woofer Size | in [mm] 6 1/2 [160] Tweeter Size | in [mm] 3/4 [20] Dome Material Titanium Peak Power | [watts] 300 Continuous Power | [watts RMS] 100 Effective Frequency Range | Hz 35-21k Woofer Mounting Hole Diameter | in [mm] 4 13/16 [123] Woofer Bottom Mount Depth | in [mm] 1 11/16 [43] Flush Mounting Tweeter Hole Diameter | in [mm] 1 9/16 [40] Flush Mount Tweeter Depth | in [mm] 9/16 [14.5] High Pass | dB, at Frequency | Hz 12, 4000 Low Pass | dB, at Frequency | Hz 12, 4000 High Frequency Output Attenuation | dB 0, 3, & 6 Bolt-Thru Grilles Yes Kicker CS Component Speaker Manual

    Pre-Order Today!

    $179.99

  • Alpine KTE-S65G : 6.5" Speaker Grille

    Alpine KTE-S65G : 6.5" Speaker Grille

    Pre-Order Today!

    Alpine 6 1/2" Grilles for Alpine R-Series and S-Series Speakers

    Pre-Order Today!

    $19.99

  • Alpine KTE-S69G : 6x9" Speaker Grille

    Alpine KTE-S69G : 6x9" Speaker Grille

    Pre-Order Today!

    Alpine 6 x 9" Speaker Grille for Alpine R-Series and S-Series Speakers

    Pre-Order Today!

    $19.99

  • Alpine SPV-65X-WRA : 6.5" 75W Speaker System for Wrangler JK 2007-2018

    Alpine SPV-65X-WRA : 6.5" 75W Speaker System, 2007-2018 Wrangler JK

    Pre-Order Today!

    Alpine 75-Watt 2-Way Component Speaker-System for 2007-2018 Jeep Wrangler-JK These 6.5-inch speakers in the SPV-65X-WRA are tuned specifically for the JK’s in-cabin environment and fit into the factory speaker locations for an easy update that will impress your ears. The SPV-65X-WRA comes with adapters that allow the speakers to be installed as a component set by mounting the tweeters into the tombstones of older JKs or onto the dash for newer JKs. For older JKs that have a sound bar, the adapters convert the speakers into a coaxial design so they can be installed into the sound bar. Driving with the top off is part of the fun of owning a Wrangler, but sometimes you get caught off-guard with the top down and inclement weather. The SPV-65X-WRA is weather resistant and rated IP55, so it’s protected from limited dust ingress and low-pressure water spray from any direction. Specifications 6.5” Component or Coaxial 2-Way Speaker System w/ Convertible Design Weather Resistant (IP55 rating) Power Handling: 75W RMS/225W Peak Nominal Impedance 4Ω Frequency Response: 65-22kHz 1” Teteron Dome Tweeter CustomSteel Frame w/ factory speaker mounting tabs OEM speaker connectors

    Pre-Order Today!

    $219.99

  • Alpine PSS-22WRA : 600W Speaker System for Wrangler JK Unlimited 2011-2018

    Alpine PSS-22WRA : 600W Speaker System, 2011-2018 Wrangler JK Unlimited

    Pre-Order Today!

    A premium sound system for your Jeep Wrangler JK Unlimited is. The PSS-22WRA is a 1200-watt, 9-speaker sound system for 2011-2018 Jeep Wrangler JK Unlimited, providing excellent sound performance with the top on or off.  Caught with the top off in inclement weather? Not to worry.  The PSS-22WRA is IP55 rated, so it can withstand rain and dust. The subwoofer uses rust resistant hardware and can handle water from off-roading adventures or a quick rinse down.  The PSS-22WRA’s subwoofer and amplifier don’t take up any usable space since they mount under the passenger’s seat for an easy bolt-in installation with simple wire routing. All necessary installation accessories are included.  The included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-22WRA is compatible with any Alpine Restyle Jeep Wrangler dash system, the Jeep factory base radio, or other aftermarket radio. Specifications Direct fit weather resistant (IP55) speaker package for non-amplified 2011– 2018 4-door Jeep® Wrangler JK Unlimited 600W RMS System SPV-65X-WRA 6.5-inch Convertible Component/Coax water resistant speaker kit SBV-10-WRA 10-inch under passenger seat water resistant enclosed subwoofer KTA-30FW – 75W X 4ch Water Resistant Amplifier KTA-30MW – 300W Water Resistant Mono Amplifier Plug & play sound system Compatible with an Alpine Restyle In-Dash system, aftermarket head unit, or with the factory Jeep radio Includes remote bass knob, vehicle specific harnesses and mounting brackets Alpine PSS-22WRA Manual

    Pre-Order Today!

    $1,699.99


You have seen 48 out of 51 products

Login

Forgot your password?

Don't have an account yet?
Create account