At this present time our store location is open by appointment only.

300W x 1 @ 4Ω

Amplifiers with a Power Output Rating of 300-Watts x 1-Channels, 4-Ohm Final Impedance

Amplifiers with a Power Output Rating of 300-Watts x 1-Channels, 4-Ohm Final Impedance

RMS power: This rating of any amplifier is the continuous power rating that an amp is designed to output at a maximum continued volume rating. The RMS power specification is one of two numbers to go by when pairing your speakers with an amplifier, not the only 2 but a good starting point. As an example, a speaker driver with a 300-Watt, or 300W for short, RMS rating should be paired with a three-hundred-watt RMS amplifier. We usually recommend an amp to be over powered by 10% RMS so that the power-plant does not have to work at 100% capacity to get 100-percent efficiency from your speakers. This will keep your amplifier from overheating during long periods of continuous operation.

Ohms: Is the resistance rating of an amp and is the second most important when pairing drivers with amplifiers. A power-plant that is 300W @ 4-ohm might put out 600-Watts @ 2Ω. When purchasing an amplifier, the correct pairing of a speaker’s RMS wattage and Ohm ratings with an amp’s output power rating is absolutely essential.

3 products

  • Alpine HDA-V90 : 5ch Hi-Res Automotive Amplifier, front side. Alpine HDA-V90 : 5ch Hi-Res Automotive Amplifier, 75W x 4ch + 500W x 1 @ 2Ω

    Alpine HDA-V90 : 5ch Hi-Res Automotive Amplifier, 75W x 4ch + 500W x 1 @ 2Ω

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res Alpine-F#1Status system technologies, the Alpine Status-System features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24Bit playback. Powering a Hi-Res sound system without contributing noise during playback requires efficiency and precision and the HDA-V90 was intentionally designed to provide impressive power output to the system while ensuring the purest audio performance. The amplifier’s wide dynamic range capability provides impressive output in a compact chassis that fits most vehicle applications. The HDA-V90 features a high-efficiency digital circuit design that ensures ultra- low distortion levels for precise sound reproduction and superb sound quality. Intentional designs, like a copper-plated chassis and black circuit board, bring the signal-to-noise ratio up to 87dB and minimize noise and distortion during playback for complete music fidelity that’s true to the original source. Featuring technology unique to Alpine, the amplifier features Alpine’s dual negative feedback control circuit to improve linearity for the most accurate sound amplification. This technology also stabilizes the amplifier output while driving the speakers and subwoofers for ultimate reliability. The HDA-V90 features Alpine’s quick- connect power and speaker connectors for quick and safe installation. The one- sided terminal layout and top-panel sound controls give the user quick access to controls on the amplifier. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Specifications Dimensions: 11.4375” x 7.5” x 2.125” Power Rating: (14.4V, ≤1.0% THD+N) 75W x 4 + 300W x 1 @ 4Ω 100W x 4 + 500W x 1 @ 2Ω Bridged: 200W x 2 @ 4Ω (ch1/2, ch3/4 only) THD+N: 0.02% (10W into 4ohm) S/N Ratio: 87dB (1W into 4ohm) Frequency response: 8-60kHz (-3dB) Damping factor: 500 (ch1/2/3/4), 1000 (subwoofer) Selectable input level – HI/LO Selectable 2/4/6ch input Variable High pass / Low pass crossover Variable Subsonic filter (subwoofer) Bass EQ (0 to +12dB, Variable) Auto-turn on with remote sensing

    Pre-Order Today!

    $899.99

  • Last One! JL Audio MX500/1 : 500W Mono Marine Amplifier @ 2Ω JL Audio MX500/1 : 500W Mono Marine Amplifier, side view.

    JL Audio MX500/1 : 500W Mono Marine Amplifier @ 2Ω

    1 Available for pickup

     MX-Series 500-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 300W @ 4-Ohm Engineered specifically for powersports applications, the MX500/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. With a robust 500W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX500/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch. Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 12 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >97 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >70 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >115 / 50 Hz Damping Factor @ 2 Ω >54 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) @ 4 Ω 300 W RMS x 1 @ 3 Ω 400 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A JL Audio MX500/1 Manual

    1 Available for pickup

    $449.99

  • Kicker 46CXA8001t : Mono Amplifier, 600-Watts at 2-Ohm, 300-Watts at 4-Ohm Mono 600W Amplifier @ 2Ω, or 300W @ 4Ω : Kicker 46CXA8001t top side view.

    Kicker 46CXA8001t : Mono 600W Amplifier @ 2Ω, or 300W @ 4Ω

    Pre-Order Today!

    Mono Amplifier, 600-Watts at 2-Ohm, 300-Watts at 4-Ohm This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash. Efficient Class-D amplifier Three-second turn-on/off delay to eliminate unwanted interference Variable 12dB crossovers provides control to dial in perfect sound KickEQ™ 6dB variable bass boost for those additional low frequencies 24dB subsonic filter for protection from potentially damaging frequencies FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio Accepts up to 40-volt input signal Small footprint for easier installation Vertical mounting hardware included for another unique look This Kicker 46CXA8001t amplifier delivers as much as 600W into one bass channel. Specifications MODEL CXA800.1 Power (watts/ch) 4 Ohm 300x1 Power (watts/ch) 2 Ohm 600x1 Power (watts/ch) 1 Ohm 800x1 CXRC Remote Bass Capable (sold sep.) yes Dimensions (in, cm) (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)8-1/8, 20.6 Frequency Response (Hz): 25-200, +0/-1dB Input Sensitivity: 250mV-10V (Low Level)1V-40V (High Level) Signal-to-Noise Ratio: >95dB, a-weighted, re: rated power Active Crossover: Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter: 25Hz @24dB/octave KickEQ™ Boost Variable 0-6dB @40Hz Kicker CXA Mono Amplifier Manual

    Pre-Order Today!

    $299.99

Login

Forgot your password?

Don't have an account yet?
Create account