At this present time our store location is open by appointment only.

400W RMS

Subs, Speakers and Electronics with an RMS Power Rating of 400-Watts

Subs, Speakers and Electronics with an RMS Power Rating of 400-Watts

The RMS rating of any speaker or subwoofer driver is the continuous power rating that the driver is designed to handle at a maximum volume rating. The RMS rating is one of two numbers to go by when pairing your speakers with an amplifier. As an example, a speaker with a 400-Watt, or 400W for short, RMS rating should be paired with a four-hundred-watt RMS amp. We usually recommend a power-plant to be over powered by 10 – 20% RMS so that the amplifier does not have to work at 100% capacity to get 100% efficiency from your speakers.

35 products

  • JL Audio 10TW3 : 400W 10" Thin Subwoofer Driver, 4Ω or 8Ω Dual Voice Coil JL Audio 10TW3 : 400W 10" Thin Subwoofer Driver, 4Ω or 8Ω Dual Voice Coil, top side.

    JL Audio 10TW3 : 400W 10" Thin Subwoofer Driver, 4Ω or 8Ω Dual Voice Coil

    Pre-Order Today!

    TW3-Series 10-Inch 400-Watt Automotive Subwoofer Driver, 4Ω or 8Ω DVC  The 10" TW3 thin subwoofer driver by JL Audio delivers a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of greater excursion than JL's W3v3 subwoofers! JL Audio’s patented thin-line woofer technology compresses the architecture of the 10TW3 using a “concentric tube” structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of the large motor structure further forward in the speaker than with conventional 10-Inch thin subwoofer designs. The 10TW3-D4 and 10TW3-D8 subwoofers are optimized for small enclosures and offer JL's tab-ear mounting design to maximize cone area within their mounting footprints. Very shallow mounting depth (3.25 / 3.50 Inches) No pole vent: permits mounting close to rear wall of enclosure. Very small sealed enclosure volume requirements Very long linear excursion capability (0.60 In / 15.2 mm, one-way) DMA-optimized motor designs “concentric tube” architecture Patented “floating cone attach method” technology Cast alloy frame Injection molded, mica-filled polypropylene cone Rubber surround Aluminum-alloy dust cap and rear cap with JL Audio logo Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling 400W RMS Recommended Amplifier Power 200W - 400W RMS Nominal Impedance Dual 4Ω/8Ω JL Audio 10TW3 Manual

    Pre-Order Today!

    $449.99

  • JL Audio 12TW3 : 12-Inch 400-Watt Thin Subwoofer Driver, 4-Ohm or 8-Ohm DVC, front side view. 400W 12" Thin Subwoofer Driver, 4Ω or 8Ω Dual Voice Coil : JL Audio 12TW3

    JL Audio 12TW3 : 400W 12" Thin Subwoofer Driver, 4Ω or 8Ω Dual Voice Coil

    Pre-Order Today!

    TW3-Series 12-Inch 400-Watt Thin Subwoofer Driver, 4-Ohm or 8-Ohm DVC The 12" TW3 thin subwoofer driver by JL Audio offers a shallow mounting depth with an excursion capability that is remarkably capable of greater excursion than JL's W3v3 full size subwoofers. JL Audio’s TW3 sub utilizes a patented thin-line woofer technology that compresses the architecture of the 12TW3 woofer using a “concentric tube” structure built into the injection-molded cone body. This structure supports the voice coil and spider, while allowing the placement of the large motor structure to be moved further forward on the chassis than with conventional designs. JL Audio 12TW3-D4 and 12TW4-D8 are optimized for small enclosures and offers JL's tab-ear mounting design to maximize cone area within their mounting footprints. Deep, powerful and accurate JL Audio bass is now possible in more applications than ever. Very shallow mounting depth (3.25 / 3.50 Inches) No pole vent: permits mounting close to rear wall of enclosure. Very small sealed enclosure volume requirements Very long linear excursion capability (0.60 In / 15.2 mm, one-way) DMA-optimized motor designs “concentric tube” architecture Patented “floating cone attach method” technology Cast alloy frame Injection molded, mica-filled polypropylene cone Rubber surround Aluminum-alloy dust cap and rear cap with JL Audio logo Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling 400W RMS Recommended Amplifier Power 200W - 400W RMS Nominal Impedance Dual 4Ω/8Ω JL Audio 12TW3 Manual

    Pre-Order Today!

    $499.99

  • Last One! JL Audio ACP110LG-TW1 : 10" Powered Thin Subwoofer Enclosure - 400W JL Audio ACP110LG-TW1 : 10" Powered Thin Subwoofer Enclosure, side view.

    JL Audio ACP110LG-TW1 : 10" Powered Thin Subwoofer Enclosure - 400W Ported

    1 Available for pickup

    TW1-Series 400-Watt Amplified 10-Inch Ported Subwoofer System With MicroSub+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this incredible subwoofer system utilizes JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency. Key to the enclosure’s performance is its efficient slot-ported design and precise tuning of its 10TW1 subwoofer driver. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space. As with all MicroSub™ systems, these amplified versions produce the kind of output and extension normally associated with much larger systems. Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω General Specifications Continuous Power Handling (RMS) Built-in amplifier 400 W @ 0.25 Ω System Nominal Impedance 0.25 Ω Input Voltage Range @ RCA Inputs 70 mV - 1.40 V RMS Input Voltage Range @ High-Level Inputs 280 mV - 5.4 V RMS Recommended Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (ATO or ATC) Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh JL Audio MicroSub+/PowerWedge+ Manual

    1 Available for pickup

    $679.99

  • Last One! JL Audio ACP112LG-TW1 : 12" Powered Thin Subwoofer Enclosure - 400W JL Audio ACP112LG-TW1 : 12" Powered Thin Subwoofer Enclosure, side view.

    JL Audio ACP112LG-TW1 : 12" Powered Thin Subwoofer Enclosure - 400W Ported

    1 Available for pickup

    TW1-Series 400-Watt Amplified 12-Inch Ported Subwoofer System With MicroSub+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this incredible subwoofer system utilizes JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency. Key to the enclosure’s performance is its efficient slot-ported design and precise tuning of its 12TW1 subwoofer driver. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space. As with all MicroSub™ systems, these amplified versions produce the kind of output and extension normally associated with much larger systems. Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω Enclosure and Subwoofer Built in USA with global components General Specifications Continuous Power Handling (RMS) Built-in amplifier 400 W @ 0.25 Ω System Nominal Impedance 0.25 Ω Input Voltage Range @ RCA Inputs 70 mV - 1.40 V RMS Input Voltage Range @ High-Level Inputs 280 mV - 5.4 V RMS Recommended Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (ATO or ATC) Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh JL Audio MicroSub+/PowerWedge+ Manual

    1 Available for pickup

    $749.99

  • Last One! JL Audio ACS110LG-TW1 : 10" Powered Thin Subwoofer Enclosure - 400W JL Audio ACS110LG-TW1 : 10" Powered Thin Subwoofer Enclosure, side view.

    JL Audio ACS110LG-TW1 : 10" Powered Thin Subwoofer Enclosure - 400W Sealed

    1 Available for pickup

    TW1-Series 400-Watt Amplified 10-Inch Subwoofer System In PowerWedge+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this subwoofer system employs JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency. Harnessing the performance and insanely small box requirements of the TW1 subwoofer driver, this subwoofer system is designed to deliver amazing sub-bass from an enclosure that is only 5 inches (127 mm) deep. Its low-profile enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW1 driver and has been fine-tuned through extensive real-world listening. Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space. Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω Enclosure and Subwoofer Built in USA with global components

 General Specifications Continuous Power Handling (RMS) Built-in amplifier 400 W @ 0.25 Ω System Nominal Impedance 0.25 Ω Input Voltage Range @ RCA Inputs 70 mV - 1.40 V RMS Input Voltage Range @ High-Level Inputs 280 mV - 5.4 V RMS Recommended Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (ATO or ATC) Enclosure Type Sealed Finish Black carpet Grille Included Black Steel Mesh JL Audio MicroSub+/PowerWedge+ Manual

    1 Available for pickup

    $629.99

  • Last One! JL Audio ACS112LG-TW1 : 12" Powered Thin Subwoofer Enclosure - 400W JL Audio ACS112LG-TW1 : 12" Powered Thin Subwoofer Enclosure, side view.

    JL Audio ACS112LG-TW1 : 12" Powered Thin Subwoofer Enclosure - 400W Sealed

    1 Available for pickup

    TW1-Series 400-Watt Amplified 12-Inch Subwoofer System In PowerWedge+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this subwoofer system employs JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency. Harnessing the performance and insanely small box requirements of the TW1 subwoofer driver, this subwoofer system is designed to deliver amazing sub-bass from an enclosure that is only 6.625 in. (168 mm) deep. Its low-profile enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW1 driver and has been fine-tuned through extensive real-world listening. Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space. Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω Enclosure and Subwoofer built in USA with global components

 General Specifications Continuous Power Handling (RMS) Built-in amplifier 400 W @ 0.25 Ω System Nominal Impedance 0.25 Ω Input Voltage Range @ RCA Inputs 70 mV - 1.40 V RMS Input Voltage Range @ High-Level Inputs 280 mV - 5.4 V RMS Recommended Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (ATO or ATC) Enclosure Type Sealed Finish Black carpet Grille Included Black Steel Mesh JL Audio MicroSub+/PowerWedge+ Manual

    1 Available for pickup

    $679.99

  • JL Audio CS110LG-TW3 : 10" Thin Subwoofer Enclosure - 400W RMS 2Ω JL Audio CS110LG-TW3 : 10" Thin Subwoofer Enclosure - 400W RMS 2Ω, side view.

    JL Audio CS110LG-TW3 : 10" Thin Subwoofer Enclosure, 400W RMS 2Ω

    Pre-Order Today!

    PowerWedge-Series 10-Inch 400-Watt Enclosed Subwoofer System, 2Ω Sealed Enclosure In this low-profile PowerWedge™ subwoofer system, JL harnesses the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 4.5 in. (114 mm) deep. This low-profile enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3-D4 and has been fine-tuned through extensive real-world listening. The PowerWedge™ subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω General Specifications Continuous Power Handling (RMS) 400 W System Nominal Impedance 2 Ω Enclosure Type Sealed Finish Black carpet Grille Included Black Steel Mesh Physical Specifications External Width (W) 20.75 in / 527 mm External Height (H) 14 in / 357 mm External Depth (D1) 4.5 in / 114 mm Net Weight 21.2 lb / 9.6 kg JL Audio CS110LG-TW3 Brochure

    Pre-Order Today!

    $529.99

  • JL Audio CS110TG-TW3 : 10" Thin Subwoofer Enclosure - 400W RMS 2Ω JL Audio CS110TG-TW3 : 10" Thin Subwoofer Enclosure - 400W RMS 2Ω, side view.

    JL Audio CS110TG-TW3 : 10" Thin Subwoofer Enclosure, 400W RMS 2Ω

    Pre-Order Today!

    PowerWedge-Series 10-Inch 400-Watt Enclosed Subwoofer System, 2Ω Sealed Enclosure In this sealed Truck PowerWedge™ subwoofer system, JL harnesses the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω General Specifications Continuous Power Handling (RMS) 400 W System Nominal Impedance 2 Ω Enclosure Type Sealed, truck enclosure Finish Black carpet Grille Included Black Steel Mesh Physical Specifications External Width (W) 19 in / 483 mm External Height (H) 12.375 in / 314 mm External Depth (D1) 6.25 in / 159 mm External Top Surface Depth (D2) 4.1 in / 104 mm Net Weight 21.2 lb / 9.6 kg JL Audio CS110TG-TW3 Brochure

    Pre-Order Today!

    $529.99

  • JL Audio CS112TG-TW3 : 12" Thin Subwoofer Enclosure - 400W RMS 2Ω JL Audio CS112TG-TW3 : 12" Thin Subwoofer Enclosure - 400W RMS 2Ω, side view.

    JL Audio CS112TG-TW3 : 12" Thin Subwoofer Enclosure, 400W RMS 2Ω

    Pre-Order Today!

    PowerWedge-Series 12-Inch 400-Watt Enclosed Subwoofer System, 2Ω Sealed Enclosure In this sealed Truck PowerWedge™ subwoofer system, JL harnesses the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω General Specifications System Nominal Impedance 2 Ω Grille Included Black Steel Mesh Finish Black carpet Enclosure Type Sealed, truck enclosure Continuous Power Handling (RMS) 400 W Physical Specifications External Width (W) 21.75 in / 537 mm External Height (H) 14.625 in / 371 mm External Depth (D1) 7 in / 178 mm External Top Surface Depth (D2) 4.5 in / 114 mm Net Weight 29 lb / 13.2 kg JL Audio CS112TG-TW3 Brochure

    Pre-Order Today!

    $549.99

  • JL Audio SB-F-F150SPRCB/10TW3 : 10" Thin 400W Subwoofer Enclosure, cutaway view. JL Audio SB-F-F150SPRCB/10TW3 : 10" Thin 400W Subwoofer Enclosure, shown installed.

    JL Audio SB-F-F150SPRCB/10TW3 : 10" Thin 400W Subwoofer Enclosure @ 2Ω, 2015-UP F-150 (SuperCab)

    Pre-Order Today!

    Single 400-Watt 10-Inch Stealthbox Subwoofer Enclosure for Select 2015-UP Ford F-150 SuperCab & 2017-UP SuperDuty SuperCab Trucks Benefitting from JL's revolutionary thin-woofer technology, this Stealthbox® for F-150 SuperCab and SuperDuty SuperCab trucks is designed to install neatly under the rear seat with no intrusion on cab space. Featuring an all-fiberglass, sealed enclosure design, JL's Stealthbox® houses a 10-inch TW3 thin-line subwoofer and fills your truck with loads of deep bass output. Seat folding and reclining are unaffected, and JL even incorporated a recess on the Stealthbox’s top for mounting an amplifier, if desired. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under rear bench seat and requires removal of the storage divider panel. Stealthbox® includes a steel-mesh grille to protect the driver. Does not affect folding or reclining of seat. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-F-F150SPRCB/10TW3 Installation Manual

    Pre-Order Today!

    $999.99

  • JL Audio SB-F-FOC5DR/10TW3 : 10" Thin 400W Subwoofer Enclosure @ 2Ω, Ford Focus 5dr 2012-2018 JL Audio SB-F-FOC5DR/10TW3 : 10" Thin 400W Subwoofer Enclosure, shown installed.

    JL Audio SB-F-FOC5DR/10TW3 : 10" Thin 400W Subwoofer Enclosure @ 2Ω, 2012-2018 Ford Focus (5 door)

    Pre-Order Today!

    Single 400-Watt Thin 10-Inch Subwoofer-Enclosure for Select 2012-2018 Ford-Focus 5-Door Hatchback Vehicles Ford’s cool little hatchback is not only fun to drive, but functional as well. This is why JL worked hard to tuck their Stealthbox® into a tiny corner of the hatch, keeping your cargo space virtually intact. Inside this Stealthbox® is the 10TW3 thin-line subwoofer. This driver has a very shallow mounting depth and is specifically optimized to operate in very compact enclosures, making it capable of delivering high quality, high impact sub-bass with any kind of music. Combined with any of JL Audio's drop-in coaxial and component speakers, the Stealthbox® will make you smile every time you dial the volume up. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in the passenger side rear cargo area. Installation requires permanent modification of the OEM cargo area floor. Will not fit the Focus sedan (4-door) or ST models. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-F-FOC5DR/10TW3 Installation Manual

    Pre-Order Today!

    $999.99

  • JL Audio SB-F-MUSCPE/12TW3 : 12" Thin 400W Subwoofer Enclosure @ 2Ω, Ford Mustang Coupe 2015-UP JL Audio SB-F-MUSCPE/12TW3 : 12" Thin 400W Subwoofer Enclosure, shown installed.

    JL Audio SB-F-MUSCPE/12TW3 : 12" Thin 400W Subwoofer Enclosure @ 2Ω, 2015-UP Ford Mustang Coupe

    Pre-Order Today!

    Single 400-Watt Thin 12-Inch Subwoofer-Enclosure for Select 2015-UP Ford Mustang-Coupe Vehicles The latest all-American pony car gets a big dose of horsepower and major technology enhancements, all packaged in a new sleek and sexy body. Sadly though, the stock audio systems just can't deliver enough bass to keep up with the Mustang's high-performance muscle. JL's Stealthbox® features an all-fiberglass, sealed enclosure design that fits in the same location as the optional factory subwoofer (and requires no holes to be drilled for installation). Equipped with their revolutionary 12TW3 thin-line subwoofer, this Stealthbox delivers deep, powerful bass that's worthy of your Mustang's heritage. The Hard Data: Contains one 12TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in the passenger side rear corner of the trunk. Factory subwoofer (if equipped) must be removed for installation of Stealthbox®. Installation in Mustang Shelby GT350 models requires relocation of additional OEM equipment. Will not fit convertible models! Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-F-MUSCPE/12TW3 Installation Manual

    Pre-Order Today!

    $1,099.99

  • JL Audio SB-FIAT-500/10TW3 : 10" Thin 400W Subwoofer Enclosure @ 2Ω, Fiat 500 2007-UP JL Audio SB-FIAT-500/10TW3 : 10" Thin 400W Subwoofer Enclosure, shown installed.

    JL Audio SB-FIAT-500/10TW3 : 10" Thin 400W Subwoofer Enclosure @ 2Ω, 2007-UP Fiat 500

    Pre-Order Today!

    Single 400-Watt 10-Inch Subwoofer-Enclosure for Select 2007-UP Fiat-500 Vehicles The Fiat 500 is praised for its clever design, excellent fuel economy and impressive handling dynamics, all achieved at an extremely affordable price. The only thing that spoils the fun is a weak audio system and very little space for an upgrade. Luckily, JL Audio has engineered the solution to your musical needs, without sacrificing precious cargo space. Their revolutionary 10TW3 thin-line subwoofer tucks against the driver-side wheel in a custom-fitted fiberglass enclosure, leaving plenty of space for cargo and no room for weak bass. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs against driver-side wheel well. Subwoofer is protected by the included black steel mesh grille. Also fits convertible models. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-FIAT-500/10TW3 Installation Manual

    Pre-Order Today!

    $999.99

  • JL Audio SB-GM-5GSUV/10TW3 : Single 10" 400W Subwoofer Enclosure @ 2Ω, 2021-UP Chevy GMC Large SUV's JL Audio SB-GM-5GSUV/10TW3 : Single 10" 400W Subwoofer Enclosure @ 2Ω, shown installed.

    JL Audio SB-GM-5GSUV/10TW3 : Single 10" 400W Subwoofer Enclosure @ 2Ω, 2021-UP Chevy GMC Large SUV's

    Pre-Order Today!

    Single 10-Inch 2-Ohm 400-Watt Subwoofer-Enclosure for Select 2021-UP Large Chevrolet and GMC SUV Vehicles GM's fifth-generation full-size SUV gets all-new, luxurious interiors, along with major enhancements in performance and technology. Unfortunately, the factory audio systems still lack quality bass reproduction. There also isn’t much room for a conventional subwoofer design, without compromising people and cargo space. To overcome this challenge, JL-Audio engineers developed a subwoofer solution that installs invisibly, behind the driver's side cargo panel, with no loss of storage space. Featuring 100% fiberglass construction, this Stealthbox is equipped with one of JL's innovative, 10-inch TW3 thin-line subwoofers in a custom-formed, sealed enclosure. The Hard Data: Contains one 10TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Stealthbox® installs behind the driver side cargo trim panel. Replaces the OEM “subwoofer” system, if equipped. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-GM-5GSUV/10TW3 Installation Manual

    Pre-Order Today!

    $1,199.99

  • JL Audio SB-GM-C7CP1/10TW3 : 10" 400W Thin Subwoofer Enclosure, C7 Corvette JL Audio SB-GM-C7CP1/10TW3 : 10" 400W Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-GM-C7CP1/10TW3 : 10" 400W Thin Subwoofer Enclosure, 2014-2022 Corvette C7 (Single Driver)

    Pre-Order Today!

    Single 10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2014-2022 Corvette C7 Stingray Vehicles The seventh-generation Corvette establishes a new benchmark for performance and style, but like most sports cars, presents a challenge when it comes to achieving excellent bass performance. This Stealthbox® solution is engineered for those wanting to keep most of the cargo space in the hatch. It is also designed to install without any screws or bolts and can be removed in seconds for track day and reinstalled just as fast. The factory targa-top stowage is not affected in any way by the Stealthbox®, so you can enjoy great bass with or without the top installed. Inside this Stealthbox® is a potent JL Audio 10-inch thinline subwoofer driver in a sealed enclosure that is expertly matched to the Corvette's acoustics. Also available with dual 10TW3 drivers model. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2-ohm mono. Installs into driver side hatch storage compartment. Steel mesh grille is included to protect the subwoofer driver. Installation does not affect storage of targa-top. No holes need to be drilled for installation. Easy to remove and replace. Use of driver's side, rear storage compartment is lost with installation. Storage compartment lid must be removed for installation, but can be replaced if Stealthbox® is removed. Will not fit convertible model. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-GM-C7CP1/10TW3 Installation Manual

    Pre-Order Today!

    $1,099.99

  • JL Audio SB-GM-CAM6G/12TW3 : 12" 400W 2Ω Thin Subwoofer Enclosure, 2016-UP Chevy Camaro JL Audio SB-GM-CAM6G/12TW3 : 12" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-GM-CAM6G/12TW3 : 12" 400W 2Ω Thin Subwoofer Enclosure, 2016-UP Chevy Camaro Coupe

    Pre-Order Today!

    Single 12-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2016 & Up Chevrolet Camaro Coupe Vehicles Chevrolet’s 6th generation Camaro delivers a powerful shot of adrenalin and all-American, classic muscle car looks. Unfortunately, its stock sound system lacks real low-frequency punch and definitely needs some help in the bass department. This Stealthbox® solution employs JL's high-technology, low-profile 12TW3 12-inch subwoofer driver and tucks neatly into the driver side, rear corner of the trunk without taking up valuable cargo space. Housed in a 100% fiberglass sealed enclosure, the 12TW3’s long excursion capability and high power handling deliver accurate and extended low frequency output at any listening level. Rear-seat pass-through functionality remains unaffected, and full access to the under floor battery compartment is retained. Also available in 12W6v3 driver model. The Hard Data: Contains one 12TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for a 2 ohm load. Installs in the driver side rear corner of the trunk. Minimal loss of trunk space. Black steel mesh woofer grille included. Installation requires permanent modification to the driver’s side trunk liner. Will not fit convertible models! Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-GM-CAM6G/12TW3 Installation Manual

    Pre-Order Today!

    $1,199.99

  • JL Audio SB-GM-COCREW2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2015-UP Colorado Canyon JL Audio SB-GM-COCREW2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-GM-COCREW2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2015-2022 Colorado, Canyon (Crew Cab)

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2015-2022 Chevrolet-Colorado and GMC-Canyon Crew-Cab Vehicles GM’s mid-size truck returns with major enhancements in power and technology, all packaged in a larger body and upscale interior with all the trimmings. Unfortunately, the factory audio systems are still lacking in the bass delivery department. JL's Stealthbox® features an all-fiberglass, sealed enclosure design that installs under the rear seat and requires no holes to be drilled for installation. Equipped with their revolutionary 10TW3 thin-line subwoofer, this Stealthbox® fills your truck with powerful, deep JL Audio bass, with no intrusion on cab space. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under the rear bench seat. Does not affect folding or reclining of seat. Requires removal of under seat storage tray. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-GM-COCREW2G/10TW3 Installation Manual

    Pre-Order Today!

    $1,199.99

  • JL Audio SB-GM-COEXT2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2015-UP Colorado Canyon Extended Cab JL Audio SB-GM-COEXT2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-GM-COEXT2G/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2015-2022 Colorado, Canyon (Extended Cab)

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2015-2022 Chevrolet-Colorado and GMC-Canyon Extended-Cab Vehicles The Colorado/Canyon offers a great combination of real truck capabilities from within a compact platform. The Extended Cab version of this mid-size truck has limited back seat space for passengers and does not leave much room for a bulky subwoofer enclosure. Fortunately, JL Audio’s Stealthbox® design team has arrived at a clever solution that mounts between the jump seats, while also creating separate storage spaces beneath each seat. Equipped with their innovative 10-inch TW3 thin-line subwoofer, this down-firing Stealthbox® features an all-fiberglass, sealed enclosure design and generates loads of great-sounding, deep, bass output. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs between and under rear jump seats. Requires removal of under-seat storage tray/cup holders and relocation of jack tools. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-GM-COEXT2G/10TW3 Installation Manual

    Pre-Order Today!

    $1,199.99

  • JL Audio SB-H-CRV2/10TW3/DG : 10" 400W 2Ω Thin Subwoofer Enclosure, 2012-2016 Honda CR-V with Black Carpet JL Audio SB-H-CRV2/10TW3/DG : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-H-CRV2/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2012-2016 Honda CR-V (with Black Carpet)

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2012-2016 Honda CR-V Vehicles with Crystal-Black-Pearl-Interior The 4th generation of Honda's popular CR-V offers even more space than its predecessor, providing ample room for people and cargo. Unfortunately, none of the factory audio options offer anything resembling powerful, accurate bass response. To address this shortcoming, JL engineered a compact Stealthbox® solution that tucks into the corner of the hatch area, while still leaving plenty of room for all the stuff you want to carry. Inside the Stealthbox® is one of their incredibly thin 10-inch TW3 drivers to fill the CR-V’s cabin with smooth, powerful bass. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 Watt power handling. Wired for 2 ohm mono. Installs against passenger-side wheel well. Stealthbox® includes a black, steel-mesh grille to protect the driver. Will not fit early 2012 3rd Generation models. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-H-CRV2/10TW3 Installation Manual

    Pre-Order Today!

    $899.99

  • JL Audio SB-HY-VELOSTR/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2011-2018 Hyundai Veloster JL Audio SB-HY-VELOSTR/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-HY-VELOSTR/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2011-2018 Hyundai Veloster

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer Enclosure for Select 2011-2018 Hyundai-Veloster Vehicles Hyundai's funky Veloster defies categorization and offers a great combination of style, practicality and clever packaging. The stock audio system, however, is not going to win any awards. JL's Stealthbox® for the Veloster is your best first step towards correcting this audio deficiency. It features a potent JL Audio 10-inch subwoofer housed in a compact, sealed, fiberglass enclosure that fits neatly into the passenger side rear corner of the trunk. The form-fitting design conserves your valuable hatch space while still permitting full access to the spare tire. A clean-looking steel mesh grille protects your investment from loose cargo. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in passenger side of rear cargo area. A steel mesh grille is included. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-HY-VELOSTR/10TW3 Installation Manual

    Pre-Order Today!

    $879.99

  • JL Audio SB-S-BRZFRS/10TW3 : 10" 600W 2Ω Thin Subwoofer Enclosure, 2013-206 Toyota 86 BRZ FR-S JL Audio SB-S-BRZFRS/10TW3 : 10" 600W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-S-BRZFRS/10TW3 : 10" 600W 2Ω Thin Subwoofer Enclosure, 2013-2016 Toyota 86, BRZ, FR-S

    Pre-Order Today!

    Single 10-Inch 600-Watt Subwoofer-Enclosure for Select 2013-Up Subaru BRZ, 2013-2016 Scion FR-S, and 2016-UP Toyota 86 Vehicles Somebody finally paid attention and designed a no-nonsense, back-to-basics sports car that puts the emphasis on driving enjoyment. Now all you need to do is add a healthy dose of JL Audio to ratchet up the listening enjoyment and make every drive even more memorable. JL's patented 10TW3 thin-line driver is the engine inside this Stealthbox® system, and it produces spectacular results from its perch in the passenger side rear corner of the trunk. Your trunk remains completely useful and your installation is neat and secure. A grille is also included to protect your investment. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in the passenger side of trunk compartment. Black steel mesh woofer grille is included. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-S-BRZFRS/10TW3 Installation Manual

    Pre-Order Today!

    $899.99

  • JL Audio SB-T-4RNRG5/10TW3 : 10" 400W Subwoofer Enclosure @ 2Ω, 2010-UP 4Runner JL Audio SB-T-4RNRG5/10TW3 : 10" 400W Subwoofer Enclosure, installed.

    JL Audio SB-T-4RNRG5/10TW3 : 10" 400W Subwoofer Enclosure @ 2Ω, 2010-UP 4Runner

    Pre-Order Today!

    Single 10-Inch 2-Ohm 400-Watt Subwoofer-Enclosure for Select 2010-UP Toyota 4Runner Vehicles The 5th Generation 4Runner has been long-overdue for a Stealthbox solution. When JL finally approached the challenge, thy knew 4Runner owners cared about the vehicle's cargo space and JL-Audio didn't want to interfere with OEM cargo slides or aftermarket cargo drawer systems. The result is the addition of a spectacular 400 watt, 10-inch subwoofer solution tucked nicely behind the factory cargo panel. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs behind factory panel in the passenger side rear cargo area. Subwoofer is protected by the included black steel mesh grille and concealed by a fabric grille. Installation requires permanent modification to the factory panel. Installation in models equipped with an "OEM" subwoofer require purchase of a standard factory panel from Toyota Parts. Will not fit models with third row seating. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-T-4RNRG5/10TW3 Installation Manual

    Pre-Order Today!

    $1,499.99

  • JL Audio SB-T-TACACG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, cutaway view. JL Audio SB-T-TACACG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-T-TACACG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2016-UP Toyota Tacoma (Access Cab)

    Pre-Order Today!

    Single 10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2016-Up Toyota-Tacoma Access-Cab Pickups The Access Cab version of Toyota's midsize truck has minimal backseat space for passengers and almost no room for a bulky subwoofer enclosure. JL Audio’s Stealthbox® design team developed a clever solution that mounts between the jump seats, creating a nice arm rest with dual storage trays for rear passengers. Equipped with their innovative 10-inch TW3 thin-line subwoofer, this downfiring Stealthbox® features an all-fiberglass, sealed enclosure design and delivers stunning deep-bass output. Rear seat folding remains unaffected. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Replaces rear center console. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-T-TACACG3/10TW3 Installation Manual

    Pre-Order Today!

    $899.99

  • JL Audio SB-T-TACDC12/10TW3 : 10" 400W RMS 2Ω Thin Subwoofer Enclosure, Toyota Tacoma Double Cab JL Audio SB-T-TACDC12/10TW3 : 10" 400W RMS 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-T-TACDC12/10TW3 : 10" 400W RMS 2Ω Thin Subwoofer Enclosure, 2012-2015 Toyota Tacoma (Double Cab)

    Pre-Order Today!

    10-Inch 2-Ohm 400-Watt Thin Subwoofer-Enclosure for Select 2012-2015 Toyota Tacoma Double-Cab Pickups Toyota’s Tacoma Double Cab has a highly optimized interior design with almost zero wasted space. This makes integrating a serious subwoofer a pretty major challenge, but not one that our design team could not overcome. Utilizing the small box prowess and shallow mounting depth of JL Audio's 10TW3 subwoofer, JL sculpted a Stealthbox® to fit snugly behind the rear seat, while also providing a mounting location for one of our amplifiers. The results are stunning: real, deep sub-bass and totally undisturbed interior comfort and utility. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in storage pocket behind the passenger side rear seat. The enclosure features a recess on the front for a small amplifier to be mounted. Black steel mesh woofer grille is included. Note: This vehicle is produced with two styles of rear panels. This Stealthbox® fits rear panels with an angled rib as shown in the installed photo above (to the left of the subwoofer). For vehicles with a rear panel without an angled rib, use SB-TACDC/10W1v3 (SKU#94312. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-T-TACDC12/10TW3 Installation Manual

    Pre-Order Today!

    $999.99

  • JL Audio SB-T-TACDCG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2016-UP Toyota Tacoma Double Cab JL Audio SB-T-TACDCG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-T-TACDCG3/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2016-UP Toyota Tacoma (Double Cab)

    Pre-Order Today!

    Single 10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2016-UP Toyota Tacoma Double-Cab Toyota’s Tacoma Double Cab has a highly optimized interior design with almost zero wasted space. This makes integrating a serious subwoofer a pretty major challenge, but not one that our design team could not overcome. Utilizing the small box prowess and shallow mounting depth of JL's 10TW3 subwoofer, JL Audio sculpted a Stealthbox® to fit snugly behind the rear seat. The results are stunning: real, deep sub-bass and totally undisturbed interior comfort and utility. The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in storage pocket behind the passenger side rear seat. Black steel mesh woofer grille is included. Requires relocation of factory amplifier and removal of factory “subwoofer", if so equipped. For models equipped with a factory subwoofer, you must purchase a plain (without subwoofer) passenger side rear cargo trim panel (part #64429-04040-C0) from Toyota parts. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-T-TACDCG3/10TW3 Installation Manual

    Pre-Order Today!

    $999.99

  • JL Audio SB-VW-GTI/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2006-2013 GTI Rabbit R32 JL Audio SB-VW-GTI/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, shown installed.

    JL Audio SB-VW-GTI/10TW3 : 10" 400W 2Ω Thin Subwoofer Enclosure, 2006-2013 GTI, Rabbit, R32

    Pre-Order Today!

    Single 10-Inch 400-Watt Thin Subwoofer-Enclosure for Select 2006-2013 Volkswagen-GTI and Rabbit-R32 (A5) Because hatch space is limited in the MkV Golf, JL Audio worked very hard to tuck a Stealthbox® out of the way while still providing a high-performance sub-bass experience. Every cubic inch of available space in the left rear corner of the hatch is used thanks to Stealthbox® fiberglass construction. JL Audio's thin TW3 subwoofer is a natural choice for its outstanding performance in small sealed enclosures as well as its unparalleled sound quality attributes and high output capabilities. So, while other Golf drivers struggle with small, weak subwoofer solutions (or big, silly ones), you can enjoy top-shelf bass and get on with your life. The Hard Data: Contains one 10TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for a 2 ohm load. Installs in the driver side rear corner of the trunk. Minimal loss of trunk space. Black steel mesh woofer grille included. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-VW-GTI/10TW3 Installation Manual

    Pre-Order Today!

    $899.99

  • Kicker 43CVR12 : 12-Inch 400-Watt Subwoofer Driver Kicker 43CVR12 : 12-Inch 400-Watt Subwoofer Driver, side view.

    Kicker 43CVR12 : 400W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 12" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor.  The chassis of this 12-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 12" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The 43CVR122 and 43CVR124 12-Inch subwoofers works best with a sealed or ported enclosure and 400 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 86.9 MOUNTING DEPTH [in, cm]: 6-1/4, 15.9 MOUNTING DIAMETER [in, cm]: 11, 27.8 MIN SEALED BOX VOL [cu. ft, L]: 1, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 4.6, 130 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompVR Subwoofer Manual

    Pre-Order Today!

    $169.99

  • 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT12 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT12, side view.

    Kicker 43CVT12 : 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil

    Pre-Order Today!

    12-Inch 400-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The CompVT 12" subwoofer by Kicker is a thin slimline driver that pounds in a limited space. A special four-layer voice coil provides the ability to work with serious amounts of power without the bulk of a standard subwoofer. The Kicker 43CVT122 and 43CVT124 subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 SVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 87.1 MOUNTING DEPTH [in, cm]: 4 3/8, 11.1 MOUNTING DIAMETER [in, cm]: 11, 28.1 MIN SEALED BOX VOL [cu. ft, L]: 1, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 4.6, 130 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompVT Subwoofer Manual

    Pre-Order Today!

    $189.99

  • Sale -$45.00Last One! 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10, rear view.

    Kicker 43CWR10 : 400W 10" Subwoofer Driver, 4Ω Dual Voice Coil - Discontinued

    1 Available for pickup

    10-Inch 400-Watt Subwoofer Driver, 4-Ohm DVC  The 43CWR10 10" subwoofer by Kicker has an advanced suspension system that includes a ribbed polypropylene surround and a large-diameter spider for linear movement, and a distortion-free sound. Bigger magnets, a thicker cone and an improved suspension system help make this 10-Inch 400W CompR sub to be a workhorse of a driver.The Kicker 43CWR104 12" sub work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    1 Available for pickup

    $129.99$84.99

  • Kicker 46CWTB10 : Ten-Inch Loaded Marine Subwoofer Enclosure, 400-Watt, 2Ω or 4Ω Final Impedance 10" 400W Marine Subwoofer Enclosure, 2Ω or 4Ω : Kicker 46CWTB10 shown in the vertical mounting position.

    Kicker 46CWTB10 : 400W 10" Marine Subwoofer Enclosure, 2Ω or 4Ω

    Pre-Order Today!

    Ten-Inch Loaded Marine Subwoofer Enclosure, 400-Watt, 2Ω or 4Ω Final Impedance This weatherproof TB-Series subwoofer system by Kicker delivers serious bump from any corner of your trunk, behind your truck’s seat, or even in your boat or side-by-side. Surprisingly loud, the TB subs give you the bump you want without losing the space you need. Comes with a thick ABS tube construction, a flexible horizontal or vertical mounting system and spring-loaded speaker terminals. Sub-driver Grilles Included. The marine grade Kicker 46CWTB102 and 46CWTB104 10-Inch loaded subwoofer enclosures works best with 400-watts of amplified power. Specifications Type Reflex Size (in., cm) 10, 25 Impedance (ohms) 2 Power Watts (peak/RMS) 800/400 Sensitivity (dB 1w/1m) 85.7 Box Bottom Depth (in, cm) 16-9/16, 42.1 Box Height (in, cm) Vert. Mount: 17-1/16, 43.4; Horiz. Mount: 10-3/4, 27.3 Box Width (in, cm) 10-5/8, 27 What's in the Box: 1 - Enclosure assembly2 - Vertical mounting brackets1 - Horizontal mount base1 - Horizontal mount hook(retainer)1 - Horizontal mount plate(retaining clamp)7 - stainless steel M5 x 12mm button head screws for horizontal mount plate to base and mounting brackets to enclosure11 - nylon flat washers (to be used on all mounting fasteners)4 - stainless steel pan head phillips M4 x 25mm (for mount base to vehicle)1 - owner’s manual2 - Kicker stickers Kicker CWTB Subwoofer Enclosure Manual

    Pre-Order Today!

    $399.99

  • Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, left side.

    Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC  The 48CWR10 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR102 and 48CWR104 12" subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $149.99

  • Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil, right side.

    Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompRT 10-inch subwoofer is an all-weather thin bassb driver with a pair of 2-Ohm or 4-Ohm voice coils. With a mounting depth under four inches and plenty of power handling, this go-anywhere sub is as flexible as it is powerful. A UV-resistant cone and surround help make the CompRT sound great wherever the road (or trail) takes you. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent. To make Kicker subs even more reliable, their engineers developed Forced-Air Cooling™ to help these thin subs run 20 percent cooler than before. Kicker signature red double stitching makes an outstanding bond between the improved Santoprene surround and polypropylene woofer cone. Revolutionary SoloKon™ technology joins the cone to the vented back brace, creating a single integrated unit that both cools the motor and eliminates distortion.The CompRT 10-Inch 48CWRT102 and 48CWRT104 subwoofers work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.8 MOUNTING DEPTH [in, cm]: 3 7/16, 8.8 MOUNTING DIAMETER [in, cm]: 9 1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.4, 11.3 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35 .4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6

    Pre-Order Today!

    $199.99

  • Kicker 48TCWRT10 : 400W Dual 10" Thin Subwoofer Enclosure, 2Ω Configuration Kicker 48TCWRT10 : 400W Dual 10" Thin Subwoofer Enclosure, 2Ω Configuration, left side.

    Kicker 48TCWRT102 : 400W Dual 10" Thin Subwoofer Enclosure, 2Ω Configuration

    Pre-Order Today!

    10-Inch 400-Watt Loaded Thin Dual Subwoofer Enclosure, 2-Ohm Final Impedance The CompRT 10" thin subwoofer by Kicker is a weather resistant thin sub with a 2Ω configuration with this box. The thin 10 inch sub magnet structure delivers 400W RMS of power with a chassis mounting depth of just under 3 1/2". The Kicker designed UniPlate™ back plate and solid pole piece serve as a single heat-absorbing unit to keep this 10" CompRT thin subwoofer driver nice and cool.The Kicker 43TCWRT102 10" subwoofer enclosure works best with 400 watts of RMS power. Specifications TYPE: thin-profile NO. OF WOOFERS/SIZE (in, cm): 10, 25 IMPEDANCE (Ohms): 2 Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY (dB 1w/1m): 96.5 BOX TOP DEPTH (in, cm): 3-7/16, 8.8 BOX BOTTOM DEPTH (in, cm): 6-9/16, 16.7 BOX HEIGHT (in, cm): 11-13/16, 39 BOX WIDTH (in, cm): 23-1/4, 59.1 Kicker CompRT Subwoofer Enclosure Manual

    Pre-Order Today!

    $299.99

  • Kicker 48TRTP102 : 400W Dual 10" Thin Subwoofer Enclosure Kicker 48TRTP102 : 400W Dual 10" Thin Subwoofer Enclosure, right side.

    Kicker 48TRTP102 : 400W Dual 10" Thin Subwoofer Enclosure

    Pre-Order Today!

    Dual 10-Inch Thin Subwoofer Enclosure, 400-Watt RMS, 2-Ohm The Kicker CompRT series down-firing 10-inch subwoofer enclosure comes loaded with a passive reFLEX™ subwoofer and Kicker CompRT sub, then carpeted and loaded with a single 2Ω terminal.  Covered in stylish black carpeting and built with thick MDF, these tough enclosures take serious power without taking up needed space. The TRTP 10-inch subwoofer enclosure works best with 400-watts of recommended power. Specifications TYPE: thin-profile WOOFER SIZE (in, cm): 10, 25 IMPEDANCE (Ohms): 2 Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY (dB 1w/1m): 96.5 BOX TOP DEPTH (in, cm): 13-1/4, 33.5 BOX BOTTOM DEPTH (in, cm): 13-1/4, 33.5 BOX HEIGHT (in, cm): 5-5/8, 14.2 BOX WIDTH (in, cm): 25-5/8, 65 Kicker TRTP Subwoofer Enclosure Manual

    Pre-Order Today!

    $299.99

  • Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, bottom side.

    Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil

    Pre-Order Today!

    MM-Series 400-Watt RMS 10-Inch Subwoofer Driver, 4-Ohm SVC The fiberglass-reinforced ABS basket resists flexing during heavy excursion, so your sub hits hard without distorting. Ultra-Marine certification and an IP56 rating. Specifications 10" 4-ohm subwoofer Titanium-plated composite cone Butyl rubber surround Fiberglass-reinforced ABS basket IP56 rating Power handling: 400W RMS Peak power handling: 1200W Frequency response: 28-2000Hz Sensitivity: 86dB @ 1W/1M Top mounting depth: 4.35" Cutout diameter: 9.1" Grille not included Warranty: 1 year Polk Audio MM1 Subwoofer Manual

    Pre-Order Today!

    $119.99

Login

Forgot your password?

Don't have an account yet?
Create account