Mono Amplifier, 300-Watts at 2-Ohm, 150-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA4001t amplifier delivers as much as 400W into one bass channel at 1-Ohm.
Specifications
MODEL
CXA400.1
Power (watts/ch) 4 Ohm
150x1
Power (watts/ch) 2 Ohm
300x1
Power (watts/ch) 1 Ohm
400x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm): (all models 2 3/8, 5.9H x 6 3/4, 17W x ...L)
8 1/8, 20.6
Frequency Response (Hz):
25-200, +0/-1dB
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
>95dB, a-weighted, re: rated power
Active Crossover:
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter:
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
Five-Channel Amplifier, 65-Watts x 4ch +, 300-Watts x 1ch at 2-Ohm or 150W @ 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA6605t amplifier delivers as much as 300W into one bass channel.
Specifications
MODEL
CXA660.5
Power (watts/ch) 4 Ohm Stereo
65x4
Power (watts/ch) 2 Ohm Stereo
90x4
Power (watts/ch) 4 Ohm Mono
180x2
Power (watts/ch) 4 Ohm Mono Sub Ch
150x1
Power (watts/ch) 2 Ohm Mono Sub Ch
300x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17 W x ...L)14-1/8, 35.7
Frequency Response (Hz):
10Hz-20kHz
Frequency Response (Hz – Sub Ch.):
25Hz-200Hz
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
90dB
Active Crossover:
Amp 1-2: High Pass 10-200Hz @ 12dB/OctaveSub Channel: Low Pass 50-200Hz @ 12dB/Octave
Subsonic Filter:
25Hz @24dB/Octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker 46CXA6605t Manual
RP-Series Monoblock Subwoofer Amplifier 350-Watts @ 1-Ohm, 250-Watts @ 2-Ohm, 150W @ 4-Ohm
Skar Audio engineered the RP-350.1D Class D monoblock subwoofer amplifier to be dominant in both power and reliability compared to anything else on the market in its class and physical size. Designing the most efficient, well built, high quality amplifiers is where we start here at Skar Audio, and that is exactly what is delivered in this unit. The smallest of all RP series amplifiers, the RP-350.1D is the perfect solution for when you need versatility but are not willing to sacrifice power output.
The RP-350.1D is 1-ohm stable and utilizes a wide array premium internal components that make it extremely powerful and reliable - such as its high speed MOSFET power supply and advanced PCB board layout. Conservatively rated at 350 watts RMS power at a 1-ohm load, with the capabilities of reaching beyond 388 watts at max power output. This compact, small footprint amplifier, is by far one of the most affordable monoblocks Skar Audio has ever released, and is great for powering a pair of subwoofers rated around 200 watts RMS each or a single subwoofer around 400 watts RMS.
In addition to all of the above features, the 4 gauge power and ground terminals found on the amplifier allow for maximum current flow and therefore higher power output and more efficient operation. Furthermore, you'll have full reign over your amplifier with the built-in user control panel, featuring a bass EQ switch (0, +6, +12dB), and variable adjustment tunings for gain level, low-pass filter, and subsonic filter.
Featuring 4-way protection circuitry, you'll have the peace of mind knowing that you are protected against damage to the amplifier for various reasons - including electrical shortage, over heating, low voltage, and more. This amplifier comes with a remote subwoofer level control (bass knob) allowing the user to have full control over their bass from the front of the vehicle.
General Specifications
Type
Monoblock Car Amplifier
Class
D
Bridgeable
No
Strappable
No
Fuse Rating
30 Amp
MOSFET Type
High Speed MOSFET Power Supply
Damping Factor
150<
Amplifier Width
6.20"
Bass EQ (Boost)
Yes (0‚+6 dB‚+12 dB)
Output Channels
1
RCA Line Output
No
Turn-On Circuit
Soft Turn-on Circuit
Working Voltage
8.5V - 16V
Amplifier Height
2.25"
Amplifier Length
7.54"
Subsonic Control
Off - 50Hz
Tri-Mode Capable
No
Frequency Response
20Hz - 250Hz
RMS Power at 1 Ohm
350 Watts x 1 Channel (14.4v)
Peak Power at 1 Ohm
375 Watts x 1 Channel (14.4v)
RMS Power at 2 Ohms
250 Watts x 1 Channel (14.4v)
RMS Power at 4 Ohms
150 Watts x 1 Channel (14.4v)
Efficiency at 4 Ohms
0.9
Protection Built-in?
Yes - 4-Way (Thermal‚Voltage‚Speaker‚DC)
Power & Ground Inputs
4 Gauge
Signal-to-Noise Ratio
85 dB
Low Level Input (Gain)
6V - 0.2mV
Low Pass Filter (Variable)
50Hz - 220Hz
Power & Protection Indicators
Yes - LED Indicators
Remote Bass Knob & Cable Included
Yes
Real World Amplifier Dyno Test Results
Dynamic (Peak) Power at 1 Ohm
452 Watts x 1 Channel (14.38v)
Certified (RMS) Power at 1 Ohm
378 Watts x 1 Channel (14.36v)
Skar Audio RP-Series Amplifier Installation Manual
Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm
Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker.
The KEY500.1 delivers 300 watts RMS of power to your speakers at 2-ohms. Measuring less than eight inches long and only two inches high, the KEY500.1 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.
If the temperature reaches the threshold, the Kicker KEY500.1's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption!
Specifications
Power (watts/ch), 1 Ohm mono
500
Power (watts/ch), 2 Ohm mono
300
Power (watts/ch), 4 Ohm mono
150
Standard dimensions in.(H x W x L)
1-11/16 x 4-1/8 x 8-1/8
Metric dimensions cm(H x W x L)
4.3 x 9.2 x 20.7
Frequency Response (Hz):
10-160
Input Sensitivity:
high level: 1V-40V / low level: 125mV-5V
Signal-to-Noise Ratio:
>90dB, a-weighted, re: rated power
Selectable Electronic Crossover:
Variable Low Pass 40-160 Hz, Variable High Pass 10-40 Hz
What's in the Box:
1 - fuse holder1 - manual and installation hardware
Kicker 47KEY5001 Manual
JD-Series Monoblock Amplifier, 250-Watt @ 2-Ohm or 150-Watt @ 4-Ohm
Designed to produce a healthy 250 watts into 2 ohms (14.4V, 1% THD), the JD250/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD250/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD250/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you easily set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
150 W RMS x 1
@ 3 Ω
200 W RMS x 1
@ 2 Ω
250 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD250/1 Manual
