Automotive Subwoofer Drivers

Automotive Subwoofer Driver Collection

Subwoofer drivers, also know as subs, are specific only to the lowest frequencies of the sound spectrum, and are the largest drivers in any car stereo. They are generally found in sizes of 8″ – 12″ diameters. Subs move massive amounts of air creating large pressure waves. These large pressure waves give that bottom end punch you expect from your kick drum, the undeniable funk of a bass guitar and the earthshaking bump of a house beat.

The frequency range of a subwoofer generally covers the first 2 octaves of the sound spectrum, also known as the lows. Subwoofers require their own mounting structure called a sub box. Sub boxes are built to create negative pressure on the sub to help move their large diameter cones back and forth for accurate reproduction of low end frequencies. Custom subwoofer boxes are built to meet certain cubic air space specifications of sub drivers and are sometimes custom built to fit under seats or other hidden areas to maximize the use of space in the vehicle. JL Audio’s Stealthbox's are custom designed to fit many vehicles while minimizing the footprint needed to be installed in your car.

RMS vs. MAX power: The RMS rating of any speaker driver is the continuous power rating that the speaker is designed to withstand at a maximum continued volume rating. The RMS rating is the only number to go by when pairing your speakers with an amplifier. As an example a speaker with a 100Watt, or 100W for short, RMS rating and a 300-Watt Max rating is ultimately a 100 Watt speaker. The Max rating is the temporary spikes in voltage that the speaker can handle. A 100-Watt RMS / 300-Watt Max speaker is going to outperform a 100W RMS / 250W Max speaker at higher volumes, but may not be the more detailed reference speaker.

Ohms: The Ohm rating, or resistance rating, of a speaker is an essential part of a well balanced car stereo system. Many JBL factory speaker systems have 2ohm drivers. Most aftermarket speakers are 4ohm drivers. Replacing these types of factory speakers may require a wiring bypass of the factory amplifier.

Driver resistance ratings are essential when pairing subwoofer and speaker drivers with amplifiers. An amplifier that is 750W @ 2ohms might only generally be 500W or less @ 4ohms. When purchasing a subwoofer driver the correct pairing of a subwoofer’s RMS wattage and Ohm ratings with an amplifier’s output power rating is absolutely essential.

Frequency Response: Frequencies are measured in Hertz or Hz for short. The frequency response of speaker drivers will generally fall between 20Hz and 22kHz. At 20Hz the sound spectrum begins. Every time you double your frequency you move up one octave in scale. 20-Hertz to 40-Hertz covers the first Octave, 40Hz to 80Hz covers the next octave and so on. Subwoofer drivers are generally tuned to crossover at 80 Hertz. This can depend on the subwoofer type and the type of music you listen to.

72 products

  • Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, bottom side.

    Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil

    Pre-Order Today!

    MM-Series 400-Watt RMS 10-Inch Subwoofer Driver, 4-Ohm SVC The fiberglass-reinforced ABS basket resists flexing during heavy excursion, so your sub hits hard without distorting. Ultra-Marine certification and an IP56 rating. Specifications 10" 4-ohm subwoofer Titanium-plated composite cone Butyl rubber surround Fiberglass-reinforced ABS basket IP56 rating Power handling: 400W RMS Peak power handling: 1200W Frequency response: 28-2000Hz Sensitivity: 86dB @ 1W/1M Top mounting depth: 4.35" Cutout diameter: 9.1" Grille not included Warranty: 1 year Polk Audio MM1 Subwoofer Manual

    Pre-Order Today!

    $119.99

  • Kicker 48CWRT67 : 150W 6.75" Thin Subwoofer Driver, 1Ω or 2Ω Dual Voice Coil Kicker 48CWRT67 : 150W 6.75" Thin Subwoofer Driver, 1Ω or 2Ω Dual Voice Coil, left side.

    Kicker 48CWRT67 : 150W 6.75" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    6.75-Inch 150-Watt Thin Subwoofer Driver, 1-Ohm or 2-Ohm DVC The CompRT 6.75" thin subwoofer by Kicker is a weather resistant thin sub with a 1Ω or 2Ω dual voice coil design. This thin 6.75 inch sub magnet structure delivers 150W RMS of power with a chassis mounting depth of 2 3/4". The Kicker designed UniPlate™ back plate and solid pole piece serve as a single heat-absorbing unit to keep this 6.75" CompRT thin subwoofer driver nice and cool.The CompRT 6.75-Inch subwoofer works best with a sealed or ported enclosure and 150 watts of recommended power. Specifications SIZE [in, cm]: 6 13/16, 17.3 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 150 Peak Power (watts, per ANSI/CTA-2031-A) 300 SENSITIVITY [dB 1w/1m]: 82.6 MOUNTING DEPTH [in, cm]: 2 3/4, 7 MOUNTING DIAMETER [in, cm]: 5 5/8, 14.3 MIN SEALED BOX VOL [cu. ft, L]: 0.18, 5.1 MAX SEALED BOX VOL [cu. ft, L]: 0.75, 21.24 Kicker CompRT Subwoofer Manual

    Pre-Order Today!

    $119.99

  • Last One! 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3, side view.

    JL Audio 10W1v3 : 300W 10" Subwoofer Driver, 2Ω or 4Ω

    1 Available for pickup

    W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality. The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω/4Ω JL Audio 10W1v3 Manual

    1 Available for pickup

    $229.99

  • Last One! Polk Audio MM1242SVC : 12" 420W Subwoofer Driver, 4Ω Single Voice Coil

    Polk Audio MM1242SVC : 12" 420W Subwoofer Driver, 4Ω Single Voice Coil

    1 Available for pickup

    MM-Series 420-Watt RMS 12-Inch Subwoofer Driver, 4-Ohm SVC Specifications Qty Included : 1 Driver Enclosure Type : Ultra-Marine Certified Driver Complement: (1) 12" (30.48 cm) d (Round) - Subwoofer Shape : Round Diameter : 11.1" (28.19 cm) Full-Range Mounting Depth - Top Mount : 4.65" (11.81 cm) Full-Range Mounting Depth - Bottom Mount : 5.2" (13.21 cm) Total Frequency Response : 26 Hz → 200 Hz Nominal Impedance : 4 ohms Sensitivity (1 watt @ 1 meter) : 87 dB Continuous Power Handling : 420W Peak Power Handling : 1260W Drivers Warranty : 1 years Polk Audio MM1 Subwoofer Manual

    1 Available for pickup

    $129.99

  • JL Audio 12W1v3 : 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC, front side view. 300W 12" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 12W1v3

    JL Audio 12W1v3 : 300W 12" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil

    4 Available for pickup

    W1-Series 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The 12" W1v3 automotive subwoofer driver by JL Audio is a lightweight 12-inch driver with excellent performance capabilities at a moderate 300-Watts. The design of the chassis allows an average mounting depth with no pole-vent on the back side of the magnet so the rear of the motor structure can be placed directly against an enclosure boundary. This 12" subwoofer can reproduce sub-bass with shocking extension and quality. The JL Audio 12W1v3-2 and 12W1v3-4 subwoofers are best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure.  General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω JL Audio 12W1v3 Manual

    4 Available for pickup

    $249.99

  • Sale -$40.00Last One! 300W 12" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC 300W 12" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC, side view.

    Kicker 44CWC : 300W 12" Subwoofer Driver, Dual Voice Coil - Discontinued

    1 Available for pickup

    12-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 12" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS124 and 44CWCD124 12-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 300W RMS of amplified power. Specifications Size (IN.,CM) 12, 30 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 Sensitivity (dB 1w/1m) 88.3 Frequency Response (Hz) 27-500 Mounting Depth (in, cm) 5-3/8, 13.6 Mounting Cutout (in, cm) 11, 27.9 Min Sealed Box Vol (cu. ft, L) 1.25, 35.4 Max Sealed Box Vol (cu. ft, L) 3.5, 99.1 Min Vented Box Vol (cu. ft, L) 1.75, 49.6 Max Vented Box Vol (cu. ft, L) 2.25, 63.7 Kicker CompC Subwoofer Manual

    1 Available for pickup

    $119.99$79.99

  • Sale -$200.00 JL Audio 10W3v3 : 10-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC, front side view. JL Audio 10W3v3 : 10-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC

    JL Audio 10W3v3 : 500W 10" Subwoofer Driver, 2Ω - Open Box Clearance

    2 Available for pickup

    W3-Series 10-Inch 500-Watt Subwoofer Driver, 2-Ohm SVC The JL Audio 10W3v3 subwoofer driver has excellent power handling, reasonable enclosure requirements, and a long excursion for its chassis to deliver excellent bass reproduction in 500W RMS power applications. JL Audio technologies and proprietary assembly designs in the 10W3v3-2 and 10W3v3-4 subwoofers enhance linearity and reliable performance results. The JL Audio 10W3v3 is best used with an amplifier in the 150W - 500W RMS range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.   General Specifications Continuous Power Handling 500W RMS Recommended Amplifier Power 150- 500W RMS Nominal Impedance 2Ω JL Audio 10W3v3 Manual

    2 Available for pickup

    $399.99$199.99

  • Sale -$200.00 JL Audio 12W3v3 : 12-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Single Voice Coil JL Audio 12W3v3 : 12-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Single Voice Coil, rear side view.

    JL Audio 12W3v3 : 500W 12" Subwoofer Driver, 2Ω - Open Box Clearance

    2 Available for pickup

    W3-Series 12-Inch 500-Watt Subwoofer Driver, 2-Ohm Single Voice Coil This 12-inch W3v3 subwoofer driver by JL Audio delivers world-class sound quality in a 500W RMS power package.  The JL Audio 12W3v3-2 and 12W3v3-4 automotive subs are best used with an amplifier in the 150-Watt - 500-Watt RMS range and are optimized to operate in a compact 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 2 Ω JL Audio 12W3v3 Manual

    2 Available for pickup

    $449.99$249.99

  • Sale -$80.00Last One! 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3, side view.

    JL Audio 10W1v3 : 300W 10" Subwoofer Driver, 2Ω - Open Box Clearance

    1 Available for pickup

    W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm SVC The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality. The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω JL Audio 10W1v3 Manual

    1 Available for pickup

    $229.99$149.99

  • Sale -$80.00 JL Audio 12W1v3 : 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC, front side view. 300W 12" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 12W1v3

    JL Audio 12W1v3 : 300W 12" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil - Open Box Clearance

    4 Available for pickup

    W1-Series 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The 12" W1v3 automotive subwoofer driver by JL Audio is a lightweight 12-inch driver with excellent performance capabilities at a moderate 300-Watts. The design of the chassis allows an average mounting depth with no pole-vent on the back side of the magnet so the rear of the motor structure can be placed directly against an enclosure boundary. This 12" subwoofer can reproduce sub-bass with shocking extension and quality. The JL Audio 12W1v3-2 and 12W1v3-4 subwoofers are best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure.  General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω JL Audio 12W1v3 Manual

    4 Available for pickup

    $249.99$169.99

  • Sale -$50.00 300W 10" Subwoofer Driver, 4Ω Single Voice Coil : JL Audio 10W0v3 300W 10" Subwoofer Driver, 4Ω Single Voice Coil : JL Audio 10W0v3, side view.

    JL Audio 10W0v3 : 300W 10" Subwoofer Driver, 4Ω Single Voice Coil - Open Box Clearance

    2 Available for pickup

    W0-Series 10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The JL Audio 10" W0v3 subwoofer driver is a rugged performer with excellent excursion capability and linearity while sporting a 2 inch diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. This 10 inch subwoofer is best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 0.65 cu. ft. (18.4 l) sealed enclosure, or a 1.125 cu. ft. (31.9 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 300W RMS Recommended Amplifier Power (RMS) 75W - 300W RMS Nominal Impedance (Znom) 4Ω JL Audio 10W0v3 Manual

    2 Available for pickup

    $129.99$79.99

  • Sale -$50.00 JL Audio 12W0v3 : 12-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC, front side view. 300W 12" Subwoofer Driver, 4Ω Single Voice Coil : JL Audio 12W0v3

    JL Audio 12W0v3 : 300W 12" Subwoofer Driver, 4Ω Single Voice Coil - Open Box Clearance

    2 Available for pickup

    W0-Series 12-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The 12" W0v3 subwoofer driver by JL Audio delivers excellent efficiency, excursion capability and linearity. This 12" subwoofer comes with a price point under $150.00 while supporting a beefy 2 in. diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. The JL Audio 12W0v3-4 sub is best used with amplifier power in the 75W - 300W range and is optimized to operate in a moderately sized 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 4Ω JL Audio 12W0v3 Manual

    2 Available for pickup

    $149.99$99.99

  • Sale -$50.00 Alpine S2-W8D : 8" 300W Subwoofer, 2Ω or 4Ω DVC. Alpine S2-W8D : 8" 300W Subwoofer, 2Ω or 4Ω DVC, side view.

    Alpine S2-W8D : 8" 300W Subwoofer, 2Ω or 4Ω DVC

    Pre-Order Today!

    Alpine S2-Series 300-Watt 8-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil With a power handling of 300W RMS and a peak power handling of 900W, the Next-Gen 8” S-Series Subwoofers deliver outstanding performance value. Boasting a wide frequency response range of 23Hz to 215Hz and a sensitivity of 83dB (1W/1m), these subs ensure powerful and accurate bass reproduction across a diverse range of music genres. Featuring the lightweight yet sturdy combination of carbon fiber and polypropylene, the Next-Gen S-Series Subwoofer cone delivers deep, low-distortion bass that enhances the depth and richness of your music. The Next-Generation S-Series Subwoofers contain Alpine's High Amplitude Multi-Roll (H.A.M.R.) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 15mm of one-way excursion that creates incredible accuracy from the subwoofer. A Dual Voice Coil (DVC) with easy configuration jumpers make installing the S-Series subwoofers a breeze. A new twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. Maximize the potential of your S-Series subwoofers with Alpine's perfectly power-matched S-Series amps. Power up to two S2-W8D4 subwoofers effortlessly with the 600W S2-A60M mono amplifier, or for an even bigger impact, pair up to four $2-W8D4 subs with the powerful 1200W S2-A120M amp to ensure optimal sound quality and performance. Features Dual Voice Coil Subwoofers with Configuration Jumpers  Carbon Fiber / Poly Propylene Cone Poly Propylene / Ceramic Dust Cap High-Grade Strontium Ferrite Magnets Twist-Lock Grille Mount System   High-Amplitude Multi-Roll (H.A.M.R.) Surround Push-Type Speaker Terminals (Up to 8AWG Wire Size) Specifications Power Handling: 300W RMS / 900W Peak Nominal Impedance: 4Ω Frequency Response: 23Hz - 215Hz Sensitivity (1W/1M): 82.7dB Voice Coil: 1.4" X-Max (1-Way): 13mm Magnet Weight: 34oz

    Pre-Order Today!

    $219.99$169.99

  • Sale -$50.00 Alpine S2-W10D : 10" 600W Subwoofer Driver, 2Ω or 4Ω DVC. Alpine S2-W10D : 10" 600W Subwoofer Driver, 2Ω or 4Ω DVC, side view.

    Alpine S2-W10D : 10" 600W Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    Alpine S2-Series 600-Watt 10-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil With an impressive power handling of 600W RMS and a peak power handling of 1800W, the Next-Gen 10” S-Series Subwoofers deliver outstanding performance value. Boasting a wide frequency response range of 25Hz to 215Hz and a sensitivity of 85dB (1W/1m), these subs ensure powerful and accurate bass reproduction across a diverse range of music genres. Featuring the lightweight yet sturdy combination of carbon fiber and polypropylene, the Next-Gen S-Series Subwoofer cone delivers deep, low-distortion bass that enhances the depth and richness of your music. The Next-Generation S-Series Subwoofers contain Alpine's High Amplitude Multi-Roll (H.A.M.R.) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 15mm of one-way excursion that creates incredible accuracy from the subwoofer. A Dual Voice Coil (DVC) with easy configuration jumpers make installing the S-Series subwoofers a breeze. A new twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. Maximize the potential of your S-Series subwoofers with Alpine's perfectly power-matched S-Series amps. Power a single S2-W10DVC subwoofer effortlessly with the 600W S2-A60M mono amplifier, or for an even bigger impact, pair two or more S2-W10DVC subs with the powerful 1200W S2- A120M amp to ensure optimal sound quality and performance. Features Dual Voice Coil Subwoofers with Configuration Jumpers  Carbon Fiber / Poly Propylene Cone Poly Propylene / Ceramic Dust Cap High-Grade Strontium Ferrite Magnets Twist-Lock Grille Mount System   High-Amplitude Multi-Roll (H.A.M.R.) Surround Push-Type Speaker Terminals (Up to 8AWG Wire Size) Specifications Power Handling: 600W RMS / 1800W Peak Nominal Impedance: 4Ω Frequency Response: 25Hz - 215Hz Sensitivity (1W/1M): 84.9dB Voice Coil: 2.6" X-Max (1-Way): 15mm Magnet Weight: 64oz

    Pre-Order Today!

    $249.99$199.99

  • Sale -$50.00 Alpine S2-W12D : 12" 600W Subwoofer, 2Ω or 4Ω DVC. Alpine S2-W12D : 12" 600W Subwoofer, 2Ω or 4Ω DVC, side view.

    Alpine S2-W12D : 12" 600W Subwoofer, 2Ω or 4Ω DVC

    Pre-Order Today!

    Alpine S2-Series 600-Watt 12-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil With an impressive power handling of 600W RMS and a peak power handling of 1800W, the Next-Gen 12” S-Series Subwoofers deliver outstanding performance value. Boasting a wide frequency response range of 23Hz to 215Hz and a sensitivity of 86dB (1W/1m), these subs ensure powerful and accurate bass reproduction across a diverse range of music genres. Featuring the lightweight yet sturdy combination of carbon fiber and polypropylene, the Next-Gen S-Series Subwoofer cone delivers deep, low-distortion bass that enhances the depth and richness of your music. The Next-Generation S-Series Subwoofers contain Alpine's High Amplitude Multi-Roll (H.A.M.R.) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 15mm of one-way excursion that creates incredible accuracy from the subwoofer. A Dual Voice Coil (DVC) with easy configuration jumpers make installing the S-Series subwoofers a breeze. A new twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. Maximize the potential of your S-Series subwoofers with Alpine's perfectly power-matched S-Series amps. Power a single S2-W12DVC subwoofer effortlessly with the 600W S2-A60M mono amplifier, or for an even bigger impact, pair two or more S2-W12DVC subs with the powerful 1200W S2- A120M amp to ensure optimal sound quality and performance. Features Dual Voice Coil Subwoofers with Configuration Jumpers  Carbon Fiber / Poly Propylene Cone Poly Propylene / Ceramic Dust Cap High-Grade Strontium Ferrite Magnets Twist-Lock Grille Mount System   High-Amplitude Multi-Roll (H.A.M.R.) Surround Push-Type Speaker Terminals (Up to 8AWG Wire Size) Specifications Power Handling: 600W RMS / 1800W Peak Nominal Impedance: 4Ω Frequency Response: 23Hz - 215Hz Sensitivity (1W/1M): 86.2dB Voice Coil: 2.6" X-Max (1-Way): 15mm Magnet Weight: 64oz

    Pre-Order Today!

    $269.99$219.99

  • Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, Dual Voice Coil Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, side view.

    Skar Audio EVL-65 : 200W 6.5" Subwoofer Driver, Dual Voice Coil

    Pre-Order Today!

    EVL Series 6-1/2-Inch 200-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil The Skar Audio EVL-65 D2 subwoofer was designed to be the most responsive, powerful, and efficient 6.5 inch subwoofer on the market. Don't be fooled by the size, the EVL-65 is one monster of a subwoofer, featuring a 4-layer 2" pure copper voice coil, and a powerful 39 Oz single slug ferrite motor. The small size of this driver allows it to be very versatile, as it can be used in a variety of applications where adding a woofer might not otherwise be possible. Conservatively rated at 200 watts RMS Power, and 400 watts max power, the EVL-65 features an aluminum diecast chassis which utilizes an advanced air flow cooling system to help dissipate heat. The suspension design of this subwoofer is highlighted by its unique yellow spider - which connects to the coil former with premium stitched lead wires. All of these incredible features make the EVL-65 the obvious choice when looking for a versatile 6.5-inch car subwoofer. Specifications Size 6.5" Type Car Subwoofer Cone Type Competition Grade Pressed Paper Cone RMS Power 200 Watts Peak Power 400 Watts Surround Type High Roll Rubber Surround Voice Coil Size 2.00" Magnet Slug Count Single Voice Coil Layers 4 Voice Coil Material Black Coated Copper (Pure Copper) Voice Coil Impedance Dual 2 Ω T/S Parameters Bl 13.0 n/a Fs 61.0 Hz Re Dual 2 Ω Sd 113.0 cm2 Cms 0.126 mm/N Mms 52.8 gr Qes 0.43 Qms 4.48 Qts 0.39 Vas 2.3 L Nref 0.12% Xmax 6.25 mm (one-way) Sensitvity 83.1 dB

    Pre-Order Today!

    $109.99

  • JL Audio 13W3v3 : 600W 13" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil. JL Audio 13W3v3 : 600W 13" Subwoofer Driver, back side.

    JL Audio 13W3v3 : 600W 13" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil

    Pre-Order Today!

    W3-Series 13-Inch 600-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Single Voice Coil If you have the space, it makes a tremendous sense to maximize your subwoofer system's piston area to enhance efficiency (and output). It gets even better when the larger driver delivers additional power handling and excursion. For the preceding reasons, the 13W3v3 can be the best choice for those seeking high output with great sound quality at medium power levels. As with the smaller W3v3's, several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 13W3v3 to enhance linearity and reliability. The 13W3v3 2Ω or 4Ω model is best used with an amplifier powered in the 150W - 600W range and is optimized to operate in a moderate size 1.5 cu. ft. (42.5 l) sealed enclosure, or a 2.25 cu. ft. (63.7 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 600W Recommended Amplifier Power (RMS) 150 - 600W Nominal Impedance (Znom) 4Ω Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14.0 in / 356 mm Mounting Hole Diameter (B) 12.5625 in / 319 mm Bolt Hole Circle Diameter (C) 13.2 in / 335 mm Motor Outer Diameter (D) 5.79 in / 147 mm Mounting Depth (E) 7.63 in / 194 mm Driver Displacement 0.096 cu ft / 2.72 liters Net Weight 17.75 lb / 8.05 kg Free Air Resonance (Fs) 23.66 Hz Electrical “Q” (Qes) 0.465 Mechanical “Q” (Qms) 6.774 Total Speaker “Q” (Qts) 0.435 Equivalent Compliance (Vas) 4.793 cu ft / 135.74 L One-Way Linear Excursion (Xmax)* 0.610 in / 15.5 mm Reference Efficiency (no) 0.37% Efficiency (1 W / 1 m)** 87.90 dB SPL Effective Piston Area (Sd) 103.850 sq in / 0.0670 sq m DC Resistance (Re) 3.569 Ω JL Audio 13W3v3 Manual

    Pre-Order Today!

    $499.99

  • Sale -$30.00 Alpine R2-W8D : 350W 8" Subwoofer Driver, Dual Voice Coil Alpine R2-W8D : 350W 8" Subwoofer Driver, top view.

    Alpine R2-W8D : 350W 8" Subwoofer Driver, Dual Voice Coil

    Pre-Order Today!

    R-Series 8-Inch 350-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil Since the Type R platform, Alpine’s R-Series sound system family has been known for its incredible output and reliable performance. Now Alpine introduces the next-generation of sound performance with the 2nd-Gen R-Series Subwoofers with even more bass output. The 2nd-Gen R-Series Subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control from the subwoofer cone compared to the previous generation. An integrated Faraday ring minimizes distortion for cleaner bass output. A Kevlar-treated cone ensures durability in the subwoofer for reliable performance, even at high volumes. A new polypropylene/ceramic composite dust cap ensures rigidity while also providing incredible internal damping (vibration absorption) to smooth out the bass response and reproduce tight bass. This premium, unique material also has higher heat reliability that ensures non- stop bass performance. The 2nd-Gen R-Series Subwoofers contain a Dual Voice Coil (DVC) with easy configuration jumpers that allow for flexible applications. A new “EZ- Change” twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. The R2-W8D2 and R2-W8D4 is compatible with the KTE-8G Grille System (sold separately). The 2nd-Gen R-Series Subwoofers contain Alpine’s High Amplitude Multi- Roll (HAMR) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 20mm of total cone excursion and motion that creates incredible accuracy from the subwoofer. Features Dual Voice Coil (DVC) Subwoofers with Configuration Jumpers Polypropylene/Ceramic Composite Dust Cap  Kevlar Reinforced Pulp Cone High-Performance subwoofers   Twist-Lock Grille Mount System  High-Amplitude Multi-Roll (H.A.M.R.) Surround  Large Double-Stacked Magnets Specifications 350W RMS  1000W Peak Power Handling  Frequency Response: 30Hz-200Hz  Sensitivity (1W/1m): 83.5dB   Nominal Impedance: 4Ω Voice Coil: 35mm  X-Max: 12mm Magnet Weight: 56oz  Mounting Depth: 4-3/8” (118mm) Cutout Size: 6-15/16” (176mm) Push-Type Speaker Terminals (Up to 8AWG Wire Size) CTA-2031 Compliant  Alpine R2-W8D Manual

    Pre-Order Today!

    $279.99$249.99

  • Sale -$30.00 Alpine R2-W10D : 750W 10" Subwoofer Driver, Dual Voice Coil Alpine R2-W10D : 750W 10" Subwoofer Driver, top side.

    Alpine R2-W10D : 750W 10" Subwoofer Driver, Dual Voice Coil

    Pre-Order Today!

    R-Series 10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil Since the Type R platform, Alpine’s R-Series sound system family has been known for its incredible output and reliable performance. Now Alpine introduces the next-generation of sound performance with the 2nd-Gen R-Series Subwoofers with even more bass output. The 2nd-Gen R-Series Subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control from the subwoofer cone compared to the previous generation. An integrated Faraday ring minimizes distortion for cleaner bass output. A Kevlar-treated cone ensures durability in the subwoofer for reliable performance, even at high volumes. A new polypropylene/ceramic composite dust cap ensures rigidity while also providing incredible internal damping (vibration absorption) to smooth out the bass response and reproduce tight bass. This premium, unique material also has higher heat reliability that ensures non- stop bass performance. The 2nd-Gen R-Series Subwoofers contain a Dual Voice Coil (DVC) with easy configuration jumpers that allow for flexible applications. A new “EZ- Change” twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. The R2-W10D2 and R2-W10D4 is compatible with the KTE-10G Grille System (sold separately). The 2nd-Gen R-Series Subwoofers contain Alpine’s High Amplitude Multi- Roll (HAMR) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 20mm of total cone excursion and motion that creates incredible accuracy from the subwoofer. Features Dual Voice Coil (DVC) Subwoofers with Configuration Jumpers Polypropylene/Ceramic Composite Dust Cap  Kevlar Reinforced Pulp Cone High-Performance subwoofers   Twist-Lock Grille Mount System  High-Amplitude Multi-Roll (H.A.M.R.) Surround  Large Double-Stacked Magnets Specifications 750W RMS  2250W Peak Power Handling  Frequency Response: 26Hz-200Hz  Sensitivity (1W/1m): 82.4dB   Nominal Impedance: 4Ω Voice Coil: 65mm   X-Max: 20mm Magnet Weight: 123oz  Mounting Depth: 6” (152mm) Cutout Size: 9-1/16” (231mm) Push-Type Speaker Terminals (Up to 8AWG Wire Size) CTA-2031 Compliant  Alpine R2-W10D Manual

    Pre-Order Today!

    $359.99$329.99

  • Sale -$30.00 Alpine R2-W12D : 750W 12" Subwoofer Driver, Dual Voice Coil Alpine R2-W12D : 750W 12" Subwoofer Driver, front view.

    Alpine R2-W12D : 750W 12" Subwoofer Driver, Dual Voice Coil

    Pre-Order Today!

    R-Series 12-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil Since the Type R platform, Alpine’s R-Series sound system family has been known for its incredible output and reliable performance. Now Alpine introduces the next-generation of sound performance with the 2nd-Gen R-Series Subwoofers with even more bass output. The 2nd-Gen R-Series Subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control from the subwoofer cone compared to the previous generation. An integrated Faraday ring minimizes distortion for cleaner bass output. A Kevlar-treated cone ensures durability in the subwoofer for reliable performance, even at high volumes. A new polypropylene/ceramic composite dust cap ensures rigidity while also providing incredible internal damping (vibration absorption) to smooth out the bass response and reproduce tight bass. This premium, unique material also has higher heat reliability that ensures non- stop bass performance. The 2nd-Gen R-Series Subwoofers contain a Dual Voice Coil (DVC) with easy configuration jumpers that allow for flexible applications. A new “EZ- Change” twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. The R2-W12D2 and R2-W12D4 is compatible with the KTE-12G Grille System (sold separately). The 2nd-Gen R-Series Subwoofers contain Alpine’s High Amplitude Multi- Roll (HAMR) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 20mm of total cone excursion and motion that creates incredible accuracy from the subwoofer. Features Dual Voice Coil (DVC) Subwoofers with Configuration Jumpers Polypropylene/Ceramic Composite Dust Cap  Kevlar Reinforced Pulp Cone High-Performance subwoofers   Twist-Lock Grille Mount System  High-Amplitude Multi-Roll (H.A.M.R.) Surround  Large Double-Stacked Magnets Specifications 750W RMS  2250W Peak Power Handling  Frequency Response: 24Hz-200Hz  Sensitivity (1W/1m): 84.5dB   Nominal Impedance: 4Ω Voice Coil: 65mm   X-Max: 20mm Magnet Weight: 144oz  Mounting Depth: 6-1/2” (152mm) Cutout Size: 10-7/8” (231mm) Push-Type Speaker Terminals (Up to 8AWG Wire Size) CTA-2031 Compliant  Alpine R2-W12D Manual

    Pre-Order Today!

    $409.99$379.99

  • Kicker 48CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, right side.

    Kicker 48CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    8-Inch 300-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompRT 8-inch subwoofer is an all-weather thin bass driver with a pair of 2-Ohm or 4-Ohm voice coils. With a mounting depth under three inches and plenty of power handling, this go-anywhere sub is as flexible as it is powerful. A UV-resistant cone and surround help make the CompRT sound great wherever the road (or trail) takes you. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent. To make Kicker subs even more reliable, their engineers developed Forced-Air Cooling™ to help these thin subs run 20 percent cooler than before. Kicker signature red double stitching makes an outstanding bond between the improved Santoprene surround and polypropylene woofer cone. Revolutionary SoloKon™ technology joins the cone to the vented back brace, creating a single integrated unit that both cools the motor and eliminates distortion. The CompRT 8-Inch 48CWRT82 and 48CWRT84 subwoofers work best with a sealed or ported enclosure and 300 watts of recommended power. Specifications SIZE [in, cm]: 8, 20 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 SENSITIVITY [dB 1w/1m]: 81.8 MOUNTING DEPTH [in, cm]: 2 11/16, 6.7 MOUNTING DIAMETER [in, cm]: 7, 17.7 MIN SEALED BOX VOL [cu. ft, L]: 0.2, 5.66 MAX SEALED BOX VOL [cu. ft, L]: 1.0, 28.32 MIN VENTED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX VENTED BOX VOL [cu. ft, L]: 1.2, 34 Kicker CompRT Subwoofer Manual

    Pre-Order Today!

    $169.99

  • Kicker 48CWR8 : 300W 8" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWR8 : 300W 8" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, left side.

    Kicker 48CWR8 : 300W 8" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    8-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 48CWR8 8" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR82 and 48CWR84 8" subs work best with a sealed or ported enclosure and 300 watts of recommended power. Specifications SIZE [in, cm]: 8, 20 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 SENSITIVITY [dB 1w/1m]: 82.1 MOUNTING DEPTH [in, cm]: 4-1/8, 10.5 MOUNTING DIAMETER [in, cm]: 7, 17.7 MIN SEALED BOX VOL [cu. ft, L]: 0.4, 11.3 MAX SEALED BOX VOL [cu. ft, L]: 1.0, 28.52 MIN VENTED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX VENTED BOX VOL [cu. ft, L]: 1.2, 34 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $99.99

  • Kicker 48CWR15 : 800W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWR15 : 800W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, left front.

    Kicker 48CWR15 : 800W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    15-Inch 800-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 48CWR15 15" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler. The Kicker 48CWR152 and 48CWR154 15" subs work best with a sealed or ported enclosure and 800 watts of recommended power. Specifications SIZE [in, cm]: 15, 38 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 800 Peak Power (watts, per ANSI/CTA-2031-A) 1600 SENSITIVITY [dB 1w/1m]: 89.4 MOUNTING DEPTH [in, cm]: 7 15/16, 20 MOUNTING DIAMETER [in, cm]: 13 3/4, 35 MIN SEALED BOX VOL [cu. ft, L]: 1.8, 51 MAX SEALED BOX VOL [cu. ft, L]: 3.0, 85 MIN VENTED BOX VOL [cu. ft, L]: 3.0, 85 MAX VENTED BOX VOL [cu. ft, L]: 5.0, 142 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $299.99

  • Kicker 48CWR12 : 500W 12" Subwoofer Driver, 2Ω or 4Ω DVC Kicker 48CWR12 : 500W 12" Subwoofer Driver, 2Ω or 4Ω DVC, right side.

    Kicker 48CWR12 : 500W 12" Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    12-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 48CWR12 12" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR122 and 48CWR124 12" subs work best with a sealed or ported enclosure and 500 watts of recommended power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 86.9 MOUNTING DEPTH [in, cm]: 5 3/4, 14.6 MOUNTING DIAMETER [in, cm]: 11, 27.9 MIN SEALED BOX VOL [cu. ft, L]: 1.0, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 2.0, 56.64 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $169.99

  • Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, left side.

    Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC  The 48CWR10 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR102 and 48CWR104 12" subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $149.99

  • Kicker 44CWC : 8-Inch 200-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC Kicker 44CWC : 8-Inch 200-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC, side view.

    Kicker 44CWC : 200W 8" Subwoofer Driver, 4Ω Single or Dual Voice Coil

    Pre-Order Today!

    8-Inch 200-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 8" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS84 and 44CWCD84 8-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 200W RMS of amplified power. Specifications Size (IN.,CM) 8, 20 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 200 Peak Power (watts, per ANSI/CTA-2031-A) 400 Sensitivity (dB 1w/1m) 85.6 Mounting Depth (in, cm) 3 7/8, 9.8 Mounting Diameter (in, cm) 7, 17.7 Min Sealed Box Vol (cu. ft, L) 0.5, 14.2 Max Sealed Box Vol (cu. ft, L) 1.2, 34 Min Vented Box Vol (cu. ft, L) 0.66, 18.7 Max Vented Box Vol (cu. ft, L) 1.2, 34 Kicker CompC Subwoofer Manual

    Pre-Order Today!

    $89.99

  • 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC, side view.

    Kicker 44CWC : 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil

    Pre-Order Today!

    10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 10" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS104 and 44CWCD104 10-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 300W RMS of amplified power. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 500 Sensitivity (dB 1w/1m) 86.2 Frequency Response (Hz) 30-500 Mounting Depth (in, cm) 4 13/16, 12.2 Mounting Cutout (in, cm) 9 1/8, 23.1 Min Sealed Box Vol (cu. ft, L) 1.0, 28.3 Max Sealed Box Vol (cu. ft, L) 2.4, 68 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompC Subwoofer Manual

    Pre-Order Today!

    $109.99

  • 600W 15" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC 600W 15" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC, side view.

    Kicker 44CWC : 600W 15" Subwoofer Driver, 4Ω Single or Dual Voice Coil

    Pre-Order Today!

    15-Inch 600-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 15" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS154 and 44CWCD154 15-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 600W RMS of amplified power. Specifications Size (IN.,CM) 15, 38 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 90.3 Frequency Response (Hz) 25-500 Mounting Depth (in, cm) 7, 17.7 Mounting Cutout (in, cm) 13 3/4, 35 Min Sealed Box Vol (cu. ft, L) 2.25, 63.7 Max Sealed Box Vol (cu. ft, L) 5.0, 141.6 Min Vented Box Vol (cu. ft, L) 3.0, 85 Max Vented Box Vol (cu. ft, L) 4.0, 113.3 Kicker CompC Subwoofer Manual

    Pre-Order Today!

    $179.99

  • 350W 10" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT10 350W 10" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT10, side view.

    Kicker 43CVT10 : 350W 10" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil

    Pre-Order Today!

    10-Inch 350-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The CompVT 10" subwoofer by Kicker is a thin slimline driver that pounds in a limited space. A special four-layer voice coil provides the ability to work with serious amounts of power without the bulk of a standard subwoofer. The Kicker 43CVT102 and 43CVT104 subs work best with a sealed or ported enclosure and 350 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 SVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 SENSITIVITY [dB 1w/1m]: 87.2 MOUNTING DEPTH [in, cm]: 4 1/4, 10.8 MOUNTING DIAMETER [in, cm]: 9 3/16, 23.3 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 3, 85 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompVT Subwoofer Manual

    Pre-Order Today!

    $169.99

  • 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT12 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : Kicker 43CVT12, side view.

    Kicker 43CVT12 : 400W 12" Thin Subwoofer Driver, 2Ω or 4Ω Single Voice Coil

    Pre-Order Today!

    12-Inch 400-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The CompVT 12" subwoofer by Kicker is a thin slimline driver that pounds in a limited space. A special four-layer voice coil provides the ability to work with serious amounts of power without the bulk of a standard subwoofer. The Kicker 43CVT122 and 43CVT124 subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 SVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 87.1 MOUNTING DEPTH [in, cm]: 4 3/8, 11.1 MOUNTING DIAMETER [in, cm]: 11, 28.1 MIN SEALED BOX VOL [cu. ft, L]: 1, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 4.6, 130 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompVT Subwoofer Manual

    Pre-Order Today!

    $189.99

  • Sale -$60.00Last One! Kicker 43CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω Dual Voice Coil Kicker 43CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω Dual Voice Coil, front side.

    Kicker 43CWRT8 : 300W 8" Thin Subwoofer Driver, 2Ω Dual Voice Coil - Discontinued

    1 Available for pickup

    8-Inch 300-Watt Thin Subwoofer Driver, 2-Ohm DVC The CompRT 8" thin subwoofer by Kicker is a weather resistant thin sub with a 2Ω dual voice coil design. This thin 8 inch sub magnet structure delivers 300W RMS of power with a chassis mounting depth of just under 2 3/4". The Kicker designed UniPlate™ back plate and solid pole piece serve as a single heat-absorbing unit to keep this 8" CompRT thin subwoofer driver nice and cool.The CompRT 8-Inch subwoofer works best with a sealed or ported enclosure and 300 watts of recommended power. Specifications SIZE [in, cm]: 8, 20 IMPEDANCE [Ohms]: 2 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 SENSITIVITY [dB 1w/1m]: 81.8 MOUNTING DEPTH [in, cm]: 2 11/16, 6.7 MOUNTING DIAMETER [in, cm]: 7, 17.7 MIN SEALED BOX VOL [cu. ft, L]: 0.2, 5.66 MAX SEALED BOX VOL [cu. ft, L]: 1.0, 28.32 MIN VENTED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX VENTED BOX VOL [cu. ft, L]: 1.2, 34 Kicker CompR Subwoofer Manual

    1 Available for pickup

    $159.99$99.99

  • Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil, right side.

    Kicker 48CWRT10 : 400W 10" Thin Subwoofer Driver, 2Ω or 2Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 400-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompRT 10-inch subwoofer is an all-weather thin bassb driver with a pair of 2-Ohm or 4-Ohm voice coils. With a mounting depth under four inches and plenty of power handling, this go-anywhere sub is as flexible as it is powerful. A UV-resistant cone and surround help make the CompRT sound great wherever the road (or trail) takes you. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent. To make Kicker subs even more reliable, their engineers developed Forced-Air Cooling™ to help these thin subs run 20 percent cooler than before. Kicker signature red double stitching makes an outstanding bond between the improved Santoprene surround and polypropylene woofer cone. Revolutionary SoloKon™ technology joins the cone to the vented back brace, creating a single integrated unit that both cools the motor and eliminates distortion.The CompRT 10-Inch 48CWRT102 and 48CWRT104 subwoofers work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.8 MOUNTING DEPTH [in, cm]: 3 7/16, 8.8 MOUNTING DIAMETER [in, cm]: 9 1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.4, 11.3 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35 .4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6

    Pre-Order Today!

    $199.99

  • Kicker 48CWRT12 : 500W 12" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWRT12 : 500W 12" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, right side.

    Kicker 48CWRT12 : 500W 12" Thin Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 500-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompRT 12-inch subwoofer is an all-weather thin bassb driver with a pair of 2-Ohm or 4-Ohm voice coils. With a mounting depth under four inches and plenty of power handling, this go-anywhere sub is as flexible as it is powerful. A UV-resistant cone and surround help make the CompRT sound great wherever the road (or trail) takes you. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent. To make Kicker subs even more reliable, their engineers developed Forced-Air Cooling™ to help these thin subs run 20 percent cooler than before. Kicker signature red double stitching makes an outstanding bond between the improved Santoprene surround and polypropylene woofer cone. Revolutionary SoloKon™ technology joins the cone to the vented back brace, creating a single integrated unit that both cools the motor and eliminates distortion.The CompRT 12-Inch 48CWRT122 and 48CWRT124 subwoofers work best with a sealed or ported enclosure and 500 watts of recommended power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 85.5 MOUNTING DEPTH [in, cm]: 3 3/4,9.6 MOUNTING DIAMETER [in, cm]: 11, 27.9 MIN SEALED BOX VOL [cu. ft, L]: 0.55, 15.57 MAX SEALED BOX VOL [cu. ft, L]: 2.0, 56.64 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompRT Subwoofer Manual

    Pre-Order Today!

    $229.99

  • 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CVR10 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CVR10, side view.

    Kicker 43CVR10 : 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 350-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 10" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor.  The chassis of this 10-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The 43CVR102 and 43CVR104 10-Inch subwoofers works best with a sealed or ported enclosure and 350 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 SENSITIVITY [dB 1w/1m]: 83.6 MOUNTING DEPTH [in, cm]: 5 1/2, 14 MOUNTING DIAMETER [in, cm]: 9 3/16, 23.3 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 3, 85 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompVR Subwoofer Manual

    Pre-Order Today!

    $119.99

  • Kicker 43CVR12 : 12-Inch 400-Watt Subwoofer Driver Kicker 43CVR12 : 12-Inch 400-Watt Subwoofer Driver, side view.

    Kicker 43CVR12 : 400W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 12" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor.  The chassis of this 12-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 12" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The 43CVR122 and 43CVR124 12-Inch subwoofers works best with a sealed or ported enclosure and 400 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 86.9 MOUNTING DEPTH [in, cm]: 6-1/4, 15.9 MOUNTING DIAMETER [in, cm]: 11, 27.8 MIN SEALED BOX VOL [cu. ft, L]: 1, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 4.6, 130 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompVR Subwoofer Manual

    Pre-Order Today!

    $169.99

  • Kicker 43CVR15 : 15-Inch 500-Watt Subwoofer Driver Kicker 43CVR15 : 15-Inch 500-Watt Subwoofer Driver, side view.

    Kicker 43CVR15 : 500W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    15-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 15" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor.  The chassis of this 15-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 15" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The Kicker 43CVR152 and 43CVR154 15" subs works best with a sealed or ported enclosure and 500 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 15, 38 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 89.2 MOUNTING DEPTH [in, cm]: 8 3/16, 20.7 MOUNTING DIAMETER [in, cm]: 13 11/16, 34.7 MIN SEALED BOX VOL [cu. ft, L]: 1.8, 51 MAX SEALED BOX VOL [cu. ft, L]: 5.2, 147 MIN VENTED BOX VOL [cu. ft, L]: 3, 85 MAX VENTED BOX VOL [cu. ft, L]: 5, 142 Kicker CompVR Subwoofer Manual

    Pre-Order Today!

    $249.99

  • Sale -$45.00Last One! 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10, rear view.

    Kicker 43CWR10 : 400W 10" Subwoofer Driver, 4Ω Dual Voice Coil - Discontinued

    1 Available for pickup

    10-Inch 400-Watt Subwoofer Driver, 4-Ohm DVC  The 43CWR10 10" subwoofer by Kicker has an advanced suspension system that includes a ribbed polypropylene surround and a large-diameter spider for linear movement, and a distortion-free sound. Bigger magnets, a thicker cone and an improved suspension system help make this 10-Inch 400W CompR sub to be a workhorse of a driver.The Kicker 43CWR104 12" sub work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    1 Available for pickup

    $129.99$84.99

  • Sale -$55.00Last One! 500W 12" Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 43CWR12 500W 12" Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 43CWR12, rear view.

    Kicker 43CWR12 : 500W 12" Subwoofer Driver, 4Ω DVC - Discontinued

    1 Available for pickup

    12-Inch 500-Watt Subwoofer Driver, 4-Ohm DVC The 43CWR12 12" subwoofer by Kicker has an advanced suspension system that includes a ribbed polypropylene surround and a large-diameter spider for linear movement, and a distortion-free sound. Bigger magnets, a thicker cone and an improved suspension system help make this 12-Inch 500W CompR sub to be a workhorse of a driver.The Kicker 43CWR124 12" sub work best with a sealed or ported enclosure and 500 watts of recommended power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 86.9 MOUNTING DEPTH [in, cm]: 5 3/4, 14.6 MOUNTING DIAMETER [in, cm]: 11, 27.9 MIN SEALED BOX VOL [cu. ft, L]: 1.0, 28.3 MAX SEALED BOX VOL [cu. ft, L]: 2.0, 56.64 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker CompR Subwoofer Manual

    1 Available for pickup

    $149.99$94.99

  • 750W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44CVX12 750W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44CVX12, front side view.

    Kicker 44CVX12 : 750W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompVX 12" subwoofer driver by Kicker is designed with high-temp dual voice coils that deliver up to 750W of amplified RMS power. A solid pole-piece provides more mass to disperse heat. A thick polypropylene cone complements the SoloKon™ cone reinforcement system and the oversized suspension system. The Kicker 44CVX122 and 44CVX124 12 inch subwoofers have a UniPlate™ extended pole piece & backplate for superior heat dissipation and satin nickel spring-loaded speaker terminals. Specifications Size (IN.,CM) 12, 30 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 750 Peak Power (watts, per ANSI/CTA-2031-A) 1500 Sensitivity (dB 1w/1m) 87.1 Frequency Response (Hz) 20-500 Mounting Depth (in, cm) 6 11/16, 16.9 Mounting Cutout (in, cm) 11 1/16, 28 Min Sealed Box Vol (cu. ft, L) 1.0, 28.3 Max Sealed Box Vol (cu. ft, L) 4.6, 130 Min Vented Box Vol (cu. ft, L) 1.75, 49.6 Max Vented Box Vol (cu. ft, L) 2.25, 63.7 Kicker CompVX Subwoofer Manual

    Pre-Order Today!

    $279.99

  • Kicker 44CVX15 : 15-Inch 1000-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC Kicker 44CVX15 : 15-Inch 1000-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC, front side view.

    Kicker 44CVX15 : 1000W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    15-Inch 1000-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompVX 15" subwoofer driver by Kicker is designed with high-temp dual voice coils that deliver up to 1000W of amplified RMS power. A solid pole-piece provides more mass to disperse heat. A thick polypropylene cone complements the SoloKon™ cone reinforcement system and the oversized suspension system. The Kicker 44CVX152 and 44CVX154 15 inch subwoofers have a UniPlate™ extended pole piece & backplate for superior heat dissipation and satin nickel spring-loaded speaker terminals. Specifications Size (IN.,CM) 15, 38 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 1000 Peak Power (watts, per ANSI/CTA-2031-A) 2000 Sensitivity (dB 1w/1m) 91.6 Frequency Response (Hz) 18-500 Mounting Depth (in, cm) 8 1/2, 21.5 Mounting Cutout (in, cm) 13 13/16, 35 Min Sealed Box Vol (cu. ft, L) 1.8, 51.0 Max Sealed Box Vol (cu. ft, L) 5.2, 147.0 Min Vented Box Vol (cu. ft, L) 3.0, 85.0 Max Vented Box Vol (cu. ft, L) 5.0, 142.0 Kicker CompVX Subwoofer Manual

    Pre-Order Today!

    $399.99

  • 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 42CWQ10 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 42CWQ10, side view.

    Kicker 42CWQ10 : 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 10" CompQ audiophile competition subwoofer driver by Kicker is the pinnacle of Kicker's round speaker line, with nearly identical construction and performance as the L7 Series square subs. The Kicker 42CWQ102 and 42CWQ104 have a 750W RMS power handling and extremely accurate bass reproduction featuring a ribbed Santoprene® surround and a BlueLace™ large-diameter progressive roll spider for extreme flexibility at 750-Watts of Continuous Power. The CompQ 10-Inch sub works best with a sealed or ported enclosure with 750 watts of recommended power. See below for more details. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz 38 Sensitivity [1W, 1m] 85.7 Qts 0.437 Qms 8.916 Qes 0.46 Re [Ω] 6.52 Vas [ft³, L] .59, 16.75 Recommended Amplifier Power (watts RMS) 700 Outer Frame Dimension [in, cm] 10 11/16, 27.2 Mounting Depth [in, cm] 6 3/8, 16.2 Mounting Cutout [in, cm] 9 3/16, 23.4 Frequency Response [Hz] 24 – 100 Kicker CompQ Subwoofer Manual

    Pre-Order Today!

    $279.99

  • Kicker 42CWQ12 : 12-Inch 850-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC 850W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 42CWQ12, side view.

    Kicker 42CWQ12 : 850W 12" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 850-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompQ 12” audiophile subwoofer by Kicker is the pinnacle of their round speaker line, with nearly identical construction and performance as their L7 square subs. The Kicker 42CWQ122 and 42CWQ124 subs were designed for high power handling and reference competition bass reproduction, this KICKER sub features Ribbed Santoprene® surrounds and a BlueLace™ large-diameter progressive roll spider for extreme flexibility at any volume level. The CompQ series 12-Inch subwoofer works best with a sealed or ported enclosure rated for 850W RMS. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz] 37 Sensitivity [1W, 1m] 86.2 Qts 0.546 Qms 8.878 Qes 0.582 Re [Ω] 5.94 Vas [ft³, L] .91 ,26 Recommended Amplifier Power (watts RMS) 850 Outer Frame Dimension [in, cm] 12 1/2, 31.8 Mounting Depth [in, cm] 7 1/8, 18.1 Mounting Cutout [in, cm] 11 1/16, 28.1 Frequency Response [Hz] 20 – 100 Kicker CompQ Subwoofer Manual

    Pre-Order Today!

    $329.99

  • Kicker 42CWQ15 : 15-Inch 1100-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC. Kicker 42CWQ15 : 15-Inch 1100-Watt Subwoofer Driver, side view.

    Kicker 42CWQ15 : 1100W 15" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    15-Inch 1100-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompQ 15” audiophile subwoofer from Kicker is their flagship round subwoofer line, with nearly identical construction and performance as the L7 square subs. The Kicker 42CWQ152 and 42CWQ154 were designed for high power handling and audiophile competition bass reproduction, this 15-Inch CompQ sub features Ribbed Santoprene® surrounds and a BlueLace™ large-diameter progressive roll spider for extreme flexibility at any volume level. This 15” subwoofer driver works best with a sealed or ported enclosure with 1,100-Watts of RMS power. See below for more details. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz] 30.6 Sensitivity [1W, 1m] 88.6 Qts 0.472 Qms 9.672 Qes 0.496 Re [Ω] 6.03 Vas [ft³, L] 2.5, 70.747 Recommended Amplifier Power (watts RMS) 1100 Outer Frame Dimension [in, cm] 15 3/8, 39.1 Mounting Depth [in, cm] 8 15/16, 22.6 Mounting Cutout [in, cm] 13 7/8, 35.2 Frequency Response [Hz] 18 – 100 Kicker CompQ Subwoofer Manual

    Pre-Order Today!

    $429.99

  • Kicker 46L7T8 : 8" 350W Thin Subwoofer Driver, 2Ω or 4Ω DVC Kicker 46L7T8 : 8" 350W Thin Subwoofer Driver, 2Ω or 4Ω DVC

    Kicker 46L7T8 : 8" 350W Thin Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    8-Inch Thin Subwoofer Driver, 350-Watt RMS, 2-Ohm or 4-Ohm Dual-Voice-Coil The Kicker Solo-Baric® L7T square subwoofer delivers more bass than a round driver, giving you up to 20% more cone area than a round sub while fitting where only a thin driver will do. Match any L7T thin sub with a KX-Series mono amplifier for an outstanding combination of power and size. Uses a sealed or ported enclosure Square sub design moves 20% more air than round subwoofers Easily mounts under or behind a deat Dual voice coil design Ribbed santoprene surround resists heat And degrading Bumped top plate for more excursion & smoother performance SoloKon™ cone with 360-degree back bracing UniPlate™ solid pole pPiece & backplate for excellent heat dissipation Durable steel basket Specifications Size (IN.,CM) 8, 20 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 Sensitivity (dB 1w/1m) 84.835 Frequency Response (Hz) 30-100 Mounting Depth (IN.,CM) 2-3/4, 7 Mounting Cutout, Square (IN.,CM) 7-3/8, 18.8 Min Rec Sealed Box Volume (CU. FT., Liters) 0.2, 5.66 Max Rec Sealed Box Volume (CU. FT., Liters) .75, 21.2 Min Rec Vented Box Volume (CU. Ft., Liters)** .8, 22.7 Max Rec Vented Box Volume (CU. Ft., Liters)** 1.2, 34 Kicker L7T Subwoofer Manual

    Pre-Order Today!

    $199.99

  • 10" Thin 500W RMS Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 46L7T10, top view. 10" Thin 500W RMS Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 46L7T10, top side view.

    Kicker 46L7T10 : 500W 10" Thin Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    10-Inch Thin Subwoofer Driver, 500-Watt RMS, 2-Ohm or 4-Ohm Dual-Voice-Coil The Kicker Solo-Baric® L7T square subwoofer delivers more bass than a round driver, giving you up to 20% more cone area than a round sub while fitting where only a thin driver will do. Match any L7T thin sub with a KX-Series mono amplifier for an outstanding combination of power and size. Uses a sealed or ported enclosure Square sub design moves 20% more air than round subwoofers Easily mounts under or behind a deat Dual voice coil design Ribbed santoprene surround resists heat And degrading Bumped top plate for more excursion & smoother performance SoloKon™ cone with 360-degree back bracing UniPlate™ solid pole pPiece & backplate for excellent heat dissipation Durable steel basket Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 Sensitivity (dB 1w/1m) 85.98 Frequency Response (Hz) 25-100 Mounting Depth (IN.,CM) 3-3/4, 9.5 Mounting Cutout, Square (IN.,CM) 9-5/16, 23.7 Min Rec Sealed Box Volume (CU. FT., Liters) .4, 11.3 Max Rec Sealed Box Volume (CU. FT., Liters) 1.25, 28.3 Min Rec Vented Box Volume (CU. Ft., Liters)** 1.25, 35.4 Max Rec Vented Box Volume (CU. Ft., Liters)** 1.75, 49.6 Kicker L7T Subwoofer Manual

    Pre-Order Today!

    $249.99

  • 12" 600W RMS Thin Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 46L7T12 12" 600W RMS Thin Subwoofer Driver, 2Ω or 4Ω DVC : Kicker 46L7T12, top side view.

    Kicker 46L7T12 : 600W 12" Thin Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    12-Inch Thin Subwoofer Driver, 600-Watt RMS, 2-Ohm or 4-Ohm Dual-Voice-Coil The Kicker Solo-Baric® L7T square subwoofer delivers more bass than a round driver, giving you up to 20% more cone area than a round sub while fitting where only a thin driver will do. Match any L7T thin sub with a KX-Series mono amplifier for an outstanding combination of power and size. Uses a sealed or ported enclosure Square sub design moves 20% more air than round subwoofers Easily mounts under or behind a deat Dual voice coil design Ribbed santoprene surround resists heat And degrading Bumped top plate for more excursion & smoother performance SoloKon™ cone with 360-degree back bracing UniPlate™ solid pole pPiece & backplate for excellent heat dissipation Durable steel basket Specifications Size (IN.,CM) 12, 30 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 86.54 Frequency Response (Hz) 25-100 Mounting Depth (IN.,CM) 4-1/8, 9.5 Mounting Cutout, Square (IN.,CM) 11-1/16, 28.1 Min Rec Sealed Box Volume (CU. FT., Liters) .55, 15.6 Max Rec Sealed Box Volume (CU. FT., Liters) 1.25, 35.4 Min Rec Vented Box Volume (CU. Ft., Liters)** 1.75, 49.6 Max Rec Vented Box Volume (CU. Ft., Liters)** 2.25, 63.7 Kicker L7T Subwoofer Manual

    Pre-Order Today!

    $299.99

  • 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R10 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R10 side view.

    Kicker 45L7R10 : 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 500-Watt Square Subwoofer Driver, 2-Ohm or 4-Ohm DVC This L7 series 10" square woofer by Kicker hosts a heavy-duty motor structure that includes a large-diameter spider for less flex, longer life and superior accuracy. On board the chassis of this 500W driver you will find dual high-temp voice coils, an injection-molded polypropylene cone, SoloKon™ 360-degree back bracing, ribbed santoprene surround with blue stitching and a UniPlate™ back plate and pole piece, plus perimeter venting for thermal heat management. The Kicker 45L7R102 and 45L7R104 square subwoofers are rated for 500W of RMS amplified power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 85.9 MOUNTING DEPTH [in, cm]: 6 1/8, 15.7 MOUNTING DIAMETER [in, cm]: 9 5/16, 23.7 MIN SEALED BOX VOL [cu. ft, L]: .66, 18.7 MAX SEALED BOX VOL [cu. ft, L]: 1, 28.3 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker L7R Subwoofer Manual

    Pre-Order Today!

    $219.99

  • 600W 12" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R12 600W 12" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R12 side view.

    Kicker 45L7R12 : 600W 12" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    12-Inch 600-Watt Square Subwoofer Driver, 2-Ohm or 4-Ohm DVC This L7 series 12" square woofer by Kicker hosts a heavy-duty motor structure that includes a large-diameter spider for less flex, longer life and superior accuracy. On board the chassis of this 600W driver you will find dual high-temp voice coils, an injection-molded polypropylene cone, SoloKon™ 360-degree back bracing, ribbed santoprene surround with blue stitching and a UniPlate™ back plate and pole piece, plus perimeter venting for thermal heat management. The Kicker 45L7R122 and 45L7R124 square subwoofers are rated for 600W of RMS amplified power. Specifications SIZE [in, cm]: 12, 30 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 SENSITIVITY [dB 1w/1m]: 86.7 MOUNTING DEPTH [in, cm]: 6 7/8, 17.4 MOUNTING DIAMETER [in, cm]: 11 1/16, 28.1 MIN SEALED BOX VOL [cu. ft, L]: .88, 24.92 MAX SEALED BOX VOL [cu. ft, L]: 2, 56.64 MIN VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 MAX VENTED BOX VOL [cu. ft, L]: 3.25, 92 Kicker L7R Subwoofer Manual

    Pre-Order Today!

    $2,249.99


You have seen 48 out of 72 products

Login

Forgot your password?

Don't have an account yet?
Create account