10" Drivers Under 6.5"

10-Inch Subwoofer Drivers that are Suitable for Enclosures with a Mounting Depth under 6 1/2-Inches

10-Inch Subwoofer Drivers that are Suitable for Enclosures with a Mounting Depth under 6 1/2-Inches

These 10" drivers are best recommended for subwoofer enclosures with a sub mounting clearance of 6.5". If your 10-inch sub box has a depth of less than 6.5-inches then not all of these drivers will fit in your box.

14 products

  • Last One! 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil : Kicker 44CWC, side view.

    Kicker 44CWC : 300W 10" Subwoofer Driver, 4Ω Single or Dual Voice Coil

    1 Available for pickup

    10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 10" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS104 and 44CWCD104 10-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 300W RMS of amplified power. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 500 Sensitivity (dB 1w/1m) 86.2 Frequency Response (Hz) 30-500 Mounting Depth (in, cm) 4 13/16, 12.2 Mounting Cutout (in, cm) 9 1/8, 23.1 Min Sealed Box Vol (cu. ft, L) 1.0, 28.3 Max Sealed Box Vol (cu. ft, L) 2.4, 68 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompC Subwoofer Manual

    1 Available for pickup

    $99.99

  • 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CVR10 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CVR10, side view.

    Kicker 43CVR10 : 350W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 350-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 10" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor.  The chassis of this 10-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The 43CVR102 and 43CVR104 10-Inch subwoofers works best with a sealed or ported enclosure and 350 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 SENSITIVITY [dB 1w/1m]: 83.6 MOUNTING DEPTH [in, cm]: 5 1/2, 14 MOUNTING DIAMETER [in, cm]: 9 3/16, 23.3 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 3, 85 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompVR Subwoofer Manual

    Pre-Order Today!

    $109.99

  • Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, bottom side.

    Polk Audio MM1042SVC : 10" 400W Subwoofer Driver, 4Ω Single Voice Coil

    Pre-Order Today!

    MM-Series 400-Watt RMS 10-Inch Subwoofer Driver, 4-Ohm SVC The fiberglass-reinforced ABS basket resists flexing during heavy excursion, so your sub hits hard without distorting. Ultra-Marine certification and an IP56 rating. Specifications 10" 4-ohm subwoofer Titanium-plated composite cone Butyl rubber surround Fiberglass-reinforced ABS basket IP56 rating Power handling: 400W RMS Peak power handling: 1200W Frequency response: 28-2000Hz Sensitivity: 86dB @ 1W/1M Top mounting depth: 4.35" Cutout diameter: 9.1" Grille not included Warranty: 1 year Polk Audio MM1 Subwoofer Manual

    Pre-Order Today!

    $119.99

  • Last One! 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 43CWR10, rear view.

    Kicker 43CWR10 : 400W 10" Subwoofer Driver, 4Ω Dual Voice Coil

    1 Available for pickup

    10-Inch 400-Watt Subwoofer Driver, 4-Ohm DVC  The 43CWR10 10" subwoofer by Kicker has an advanced suspension system that includes a ribbed polypropylene surround and a large-diameter spider for linear movement, and a distortion-free sound. Bigger magnets, a thicker cone and an improved suspension system help make this 10-Inch 400W CompR sub to be a workhorse of a driver.The Kicker 43CWR104 12" sub work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    1 Available for pickup

    $129.99

  • Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil, left side.

    Kicker 48CWR10 : 400W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC  The 48CWR10 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR102 and 48CWR104 12" subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual

    Pre-Order Today!

    $139.99

  • 300W 10" Subwoofer Driver, 4Ω Single Voice Coil : JL Audio 10W0v3 300W 10" Subwoofer Driver, 4Ω Single Voice Coil : JL Audio 10W0v3, side view.

    JL Audio 10W0v3 : 300W 10" Subwoofer Driver, 4Ω Single Voice Coil

    2 Available for pickup

    W0-Series 10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The JL Audio 10" W0v3 subwoofer driver is a rugged performer with excellent excursion capability and linearity while sporting a 2 inch diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. This 10 inch subwoofer is best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 0.65 cu. ft. (18.4 l) sealed enclosure, or a 1.125 cu. ft. (31.9 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 300W RMS Recommended Amplifier Power (RMS) 75W - 300W RMS Nominal Impedance (Znom) 4Ω JL Audio 10W0v3 Manual

    2 Available for pickup

    $149.99

  • Alpine S-W10D : 10" 600W Subwoofer Driver, 2Ω or 4Ω DVC

    Alpine S-W10D : 10" 600W Subwoofer Driver, 2Ω or 4Ω DVC

    Pre-Order Today!

    Alpine S-Series 600-Watt 10-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. Specifications 10" DVC High Performance Subwoofer Power Handling: 600W RMS/1800W Peak Push-type Insert Terminals with DVC jumper system Concealed Mount Gasket/Grille* System (*Grille sold separately) Frequency Response: 28Hz-200Hz Mounting Depth 4-11/16” Alpine S-W10D2, S-W10D4 Manual

    Pre-Order Today!

    $179.99

  • 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R10 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 45L7R10 side view.

    Kicker 45L7R10 : 500W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 500-Watt Square Subwoofer Driver, 2-Ohm or 4-Ohm DVC This L7 series 10" square woofer by Kicker hosts a heavy-duty motor structure that includes a large-diameter spider for less flex, longer life and superior accuracy. On board the chassis of this 500W driver you will find dual high-temp voice coils, an injection-molded polypropylene cone, SoloKon™ 360-degree back bracing, ribbed santoprene surround with blue stitching and a UniPlate™ back plate and pole piece, plus perimeter venting for thermal heat management. The Kicker 45L7R102 and 45L7R104 square subwoofers are rated for 500W of RMS amplified power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 85.9 MOUNTING DEPTH [in, cm]: 6 1/8, 15.7 MOUNTING DIAMETER [in, cm]: 9 5/16, 23.7 MIN SEALED BOX VOL [cu. ft, L]: .66, 18.7 MAX SEALED BOX VOL [cu. ft, L]: 1, 28.3 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker L7R Subwoofer Manual

    Pre-Order Today!

    $199.99

  • 600W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44CVX10 600W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44CVX10, front side view.

    Kicker 44CVX10 : 600W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 600-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompVX 10" subwoofer driver by Kicker is designed with high-temp dual voice coils that deliver up to 600W of amplified RMS power. A solid pole-piece provides more mass to disperse heat. A thick polypropylene cone complements the SoloKon™ cone reinforcement system and the oversized suspension system. The Kicker 44CVX102 and 44CVX104 10 inch subwoofers have a UniPlate™ extended pole piece & backplate for superior heat dissipation and satin nickel spring-loaded speaker terminals. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 85.7 Frequency Response (Hz) 24-500 Mounting Depth (in, cm) 5 15/16, 15.1 Mounting Cutout (in, cm) 9 3/16, 23.3 Min Sealed Box Vol (cu. ft, L) .8, 22.7 Max Sealed Box Vol (cu. ft, L) 3.0, 85.0 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompVX Subwoofer Manual

    Pre-Order Today!

    $199.99

  • 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3 300W 10" Subwoofer Driver, 2Ω or 4Ω Single Voice Coil : JL Audio 10W1v3, side view.

    JL Audio 10W1v3 : 300W 10" Subwoofer Driver, 2Ω or 4Ω

    3 Available for pickup

    W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality. The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω/4Ω JL Audio 10W1v3 Manual

    3 Available for pickup

    $249.99

  • 600W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44L7S10 600W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 44L7S10, side view.

    Kicker 44L7S10 : 600W 10" Square Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch Square 600-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The audiophile competition 10" L7 square sub by Kicker has an advanced motor structure that includes a large-diameter spider for less flex, longer life and superior accuracy. This 10 inch 600W driver has two dual high-temp voice coils, an injection-molded polypropylene cone, SoloKon™ 360-degree back bracing, a ribbed Santoprene surround with blue surround stitching and Kicker's patented UniPlate™ back plate and pole piece. Perimeter venting for thermal heat dispersion management keeps this earth shattering 10 inch square sub nice and cool.  This 10" L7 square sub can handle up to 600W RMS of amplifier power and comes with dual spring-loaded speaker terminals for a solid speaker wire connection. Specifications Size (IN.,CM) 10, 25.4 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 86.8 Frequency Response (Hz) 24-100 Mounting Depth (IN.,CM) 6-1/4, 15.9 Mounting Cutout, Square (IN.,CM) 9-5/16, 23.7 Min Rec Sealed Box Volume (CU. FT., Liters) 1, 28.32 Max Rec Sealed Box Volume (CU. FT., Liters) 1.25, 35.4 Min Rec Vented Box Volume (CU. Ft., Liters)** 1.25, 35.4 Max Rec Vented Box Volume (CU. Ft., Liters)** 2.25, 63.8 Kicker Solo-Baric L7 Subwoofer Manual

    Pre-Order Today!

    $249.99

  • 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 42CWQ10 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil : Kicker 42CWQ10, side view.

    Kicker 42CWQ10 : 750W 10" Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil

    Pre-Order Today!

    10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 10" CompQ audiophile competition subwoofer driver by Kicker is the pinnacle of Kicker's round speaker line, with nearly identical construction and performance as the L7 Series square subs. The Kicker 42CWQ102 and 42CWQ104 have a 750W RMS power handling and extremely accurate bass reproduction featuring a ribbed Santoprene® surround and a BlueLace™ large-diameter progressive roll spider for extreme flexibility at 750-Watts of Continuous Power. The CompQ 10-Inch sub works best with a sealed or ported enclosure with 750 watts of recommended power. See below for more details. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz 38 Sensitivity [1W, 1m] 85.7 Qts 0.437 Qms 8.916 Qes 0.46 Re [Ω] 6.52 Vas [ft³, L] .59, 16.75 Recommended Amplifier Power (watts RMS) 700 Outer Frame Dimension [in, cm] 10 11/16, 27.2 Mounting Depth [in, cm] 6 3/8, 16.2 Mounting Cutout [in, cm] 9 3/16, 23.4 Frequency Response [Hz] 24 – 100 Kicker CompQ Subwoofer Manual

    Pre-Order Today!

    $249.99


You have seen 12 out of 14 products

Login

Forgot your password?

Don't have an account yet?
Create account