These 10" drivers are best recommended for subwoofer enclosures with a sub mounting clearance of 7.25". If your 10-inch sub box has a depth of less than 7.25-inches then not all of these drivers will fit in your box.
10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 10" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS104 and 44CWCD104 10-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 300W RMS of amplified power. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 500 Sensitivity (dB 1w/1m) 86.2 Frequency Response (Hz) 30-500 Mounting Depth (in, cm) 4 13/16, 12.2 Mounting Cutout (in, cm) 9 1/8, 23.1 Min Sealed Box Vol (cu. ft, L) 1.0, 28.3 Max Sealed Box Vol (cu. ft, L) 2.4, 68 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompC Subwoofer Manual
$99.99
10-Inch 350-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC This 43CVR 10" subwoofer by Kicker uses an advanced heat dispersion system with perimeter venting to allow air to circulate while the Kicker proprietary UniPlate™ system redirects even more heat away from the motor. The chassis of this 10-Inch sub holds a pair of high-temp voice coils that move an injection molded woofer. The CompVR 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design. The 43CVR102 and 43CVR104 10-Inch subwoofers works best with a sealed or ported enclosure and 350 watts of recommended power. See below for more details. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 SENSITIVITY [dB 1w/1m]: 83.6 MOUNTING DEPTH [in, cm]: 5 1/2, 14 MOUNTING DIAMETER [in, cm]: 9 3/16, 23.3 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 3, 85 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompVR Subwoofer Manual
$109.99
MM-Series 400-Watt RMS 10-Inch Subwoofer Driver, 4-Ohm SVC The fiberglass-reinforced ABS basket resists flexing during heavy excursion, so your sub hits hard without distorting. Ultra-Marine certification and an IP56 rating. Specifications 10" 4-ohm subwoofer Titanium-plated composite cone Butyl rubber surround Fiberglass-reinforced ABS basket IP56 rating Power handling: 400W RMS Peak power handling: 1200W Frequency response: 28-2000Hz Sensitivity: 86dB @ 1W/1M Top mounting depth: 4.35" Cutout diameter: 9.1" Grille not included Warranty: 1 year Polk Audio MM1 Subwoofer Manual
$119.99
10-Inch 400-Watt Subwoofer Driver, 4-Ohm DVC The 43CWR10 10" subwoofer by Kicker has an advanced suspension system that includes a ribbed polypropylene surround and a large-diameter spider for linear movement, and a distortion-free sound. Bigger magnets, a thicker cone and an improved suspension system help make this 10-Inch 400W CompR sub to be a workhorse of a driver.The Kicker 43CWR104 12" sub work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual
$129.99
10-Inch 400-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 48CWR10 10" subwoofer is available in a 2Ω or 4Ω dual voice coil design, making it easy to get the most out of your amp. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent – all without a hint of distortion. KICKER developed Forced Air Cooling to helps their subs run 25% cooler.The Kicker 48CWR102 and 48CWR104 12" subs work best with a sealed or ported enclosure and 400 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 400 Peak Power (watts, per ANSI/CTA-2031-A) 800 SENSITIVITY [dB 1w/1m]: 84.6 MOUNTING DEPTH [in, cm]: 5-1/4, 13.3 MOUNTING DIAMETER [in, cm]: 9-1/8, 23.1 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 1.25, 35.4 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompR Subwoofer Manual
$139.99
W0-Series 10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The JL Audio 10" W0v3 subwoofer driver is a rugged performer with excellent excursion capability and linearity while sporting a 2 inch diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. This 10 inch subwoofer is best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 0.65 cu. ft. (18.4 l) sealed enclosure, or a 1.125 cu. ft. (31.9 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 300W RMS Recommended Amplifier Power (RMS) 75W - 300W RMS Nominal Impedance (Znom) 4Ω JL Audio 10W0v3 Manual
$179.99$149.99
Alpine S-Series 600-Watt 10-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. Specifications 10" DVC High Performance Subwoofer Power Handling: 600W RMS/1800W Peak Push-type Insert Terminals with DVC jumper system Concealed Mount Gasket/Grille* System (*Grille sold separately) Frequency Response: 28Hz-200Hz Mounting Depth 4-11/16” Alpine S-W10D2, S-W10D4 Manual
$190.00$179.99
10-Inch 500-Watt Square Subwoofer Driver, 2-Ohm or 4-Ohm DVC This L7 series 10" square woofer by Kicker hosts a heavy-duty motor structure that includes a large-diameter spider for less flex, longer life and superior accuracy. On board the chassis of this 500W driver you will find dual high-temp voice coils, an injection-molded polypropylene cone, SoloKon™ 360-degree back bracing, ribbed santoprene surround with blue stitching and a UniPlate™ back plate and pole piece, plus perimeter venting for thermal heat management. The Kicker 45L7R102 and 45L7R104 square subwoofers are rated for 500W of RMS amplified power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 500 Peak Power (watts, per ANSI/CTA-2031-A) 1000 SENSITIVITY [dB 1w/1m]: 85.9 MOUNTING DEPTH [in, cm]: 6 1/8, 15.7 MOUNTING DIAMETER [in, cm]: 9 5/16, 23.7 MIN SEALED BOX VOL [cu. ft, L]: .66, 18.7 MAX SEALED BOX VOL [cu. ft, L]: 1, 28.3 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 2.25, 63.7 Kicker L7R Subwoofer Manual
$199.99
10-Inch 600-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompVX 10" subwoofer driver by Kicker is designed with high-temp dual voice coils that deliver up to 600W of amplified RMS power. A solid pole-piece provides more mass to disperse heat. A thick polypropylene cone complements the SoloKon™ cone reinforcement system and the oversized suspension system. The Kicker 44CVX102 and 44CVX104 10 inch subwoofers have a UniPlate™ extended pole piece & backplate for superior heat dissipation and satin nickel spring-loaded speaker terminals. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 2 or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 85.7 Frequency Response (Hz) 24-500 Mounting Depth (in, cm) 5 15/16, 15.1 Mounting Cutout (in, cm) 9 3/16, 23.3 Min Sealed Box Vol (cu. ft, L) .8, 22.7 Max Sealed Box Vol (cu. ft, L) 3.0, 85.0 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompVX Subwoofer Manual
$199.99
W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality. The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω/4Ω JL Audio 10W1v3 Manual
$249.99
10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm DVC The 10" CompQ audiophile competition subwoofer driver by Kicker is the pinnacle of Kicker's round speaker line, with nearly identical construction and performance as the L7 Series square subs. The Kicker 42CWQ102 and 42CWQ104 have a 750W RMS power handling and extremely accurate bass reproduction featuring a ribbed Santoprene® surround and a BlueLace™ large-diameter progressive roll spider for extreme flexibility at 750-Watts of Continuous Power. The CompQ 10-Inch sub works best with a sealed or ported enclosure with 750 watts of recommended power. See below for more details. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz 38 Sensitivity [1W, 1m] 85.7 Qts 0.437 Qms 8.916 Qes 0.46 Re [Ω] 6.52 Vas [ft³, L] .59, 16.75 Recommended Amplifier Power (watts RMS) 700 Outer Frame Dimension [in, cm] 10 11/16, 27.2 Mounting Depth [in, cm] 6 3/8, 16.2 Mounting Cutout [in, cm] 9 3/16, 23.4 Frequency Response [Hz] 24 – 100 Kicker CompQ Subwoofer Manual
$249.99
10-Inch 750-Watt Square Subwoofer, 2-Ohm or 4-Ohm DVC The 10" L7 series automotive subwoofer driver by Kicker stands alone as the most unique subwoofer on the market, with a cone shape that is exclusively designed to produce more output. The Kicker 41L7102 and the 41L7104 subwoofers again reach new heights in technology and design. A 2015 CES® Innovation Award winner, Kicker L7 branded itself as the crown jewel among competition subwoofers. For more than a decade, Kicker’s square woofer earned numerous awards including several CES accolades, and the 2015 version once again makes distinctive improvements on its way to another honor. These 10-Inch L7 square subwoofers deliver 20% more surface area than a comparable circular 10" sub. A bigger cone means more air gets dispersed for each excursion cycle thus producing more sound! Kicker included oversized magnets and an aluminum voice coil, to help keep heat to a minimum. The Uniplate™ is a KICKER original design, combining the pole piece and back plate as a single, seamless unit to pull damaging heat away from the sub. Kicker's patented Santoprene™ corners allow your KICKER subs to play smooth, distortion-free music at any volume level. Kicker's Blue Lace™ spider and ribbed surround work together to give you the best suspension for your L7. You get unparalleled accuracy and volume to feel every note - every time. Specifications Rated Impedance [Ω] 2 or 4 DVC Fs [Hz] 37.5 Sensitivity [1W, 1m] 85.9 Qts 0.507 Qms 9.791 Qes 0.535 Re [Ω] 7.9 Vas [ft³, L] 1, 28.32 Recommended Amplifier Power (watts RMS) 750 Outer Frame Dimension [in, cm] 10 11/16, 27.2 Mounting Depth [in, cm] 6 7/8, 17.5 Mounting Cutout [in, cm] 9 5/16, 23.7 Frequency Response [Hz] 24 - 100 Minimum Sealed Volume ft3 (L) .8 (22.65) Maximum Sealed Volume ft3 (L) 1.25 (35.4) Kicker L7 Subwoofer Manual
$299.99
R-Series 10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil Since the Type R platform, Alpine’s R-Series sound system family has been known for its incredible output and reliable performance. Now Alpine introduces the next-generation of sound performance with the 2nd-Gen R-Series Subwoofers with even more bass output. The 2nd-Gen R-Series Subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control from the subwoofer cone compared to the previous generation. An integrated Faraday ring minimizes distortion for cleaner bass output. A Kevlar-treated cone ensures durability in the subwoofer for reliable performance, even at high volumes. A new polypropylene/ceramic composite dust cap ensures rigidity while also providing incredible internal damping (vibration absorption) to smooth out the bass response and reproduce tight bass. This premium, unique material also has higher heat reliability that ensures non- stop bass performance. The 2nd-Gen R-Series Subwoofers contain a Dual Voice Coil (DVC) with easy configuration jumpers that allow for flexible applications. A new “EZ- Change” twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. The R2-W10D2 and R2-W10D4 is compatible with the KTE-10G Grille System (sold separately). The 2nd-Gen R-Series Subwoofers contain Alpine’s High Amplitude Multi- Roll (HAMR) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 20mm of total cone excursion and motion that creates incredible accuracy from the subwoofer. Features Dual Voice Coil (DVC) Subwoofers with Configuration Jumpers Polypropylene/Ceramic Composite Dust Cap Kevlar Reinforced Pulp Cone High-Performance subwoofers Twist-Lock Grille Mount System High-Amplitude Multi-Roll (H.A.M.R.) Surround Large Double-Stacked Magnets Specifications 750W RMS 2250W Peak Power Handling Frequency Response: 26Hz-200Hz Sensitivity (1W/1m): 82.4dB Nominal Impedance: 4Ω Voice Coil: 65mm X-Max: 20mm Magnet Weight: 123oz Mounting Depth: 6” (152mm) Cutout Size: 9-1/16” (231mm) Push-Type Speaker Terminals (Up to 8AWG Wire Size) CTA-2031 Compliant Alpine R2-W10D Manual
$360.00$329.99
W3-Series 10-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10W3v3 subwoofer driver has excellent power handling, reasonable enclosure requirements, and a long excursion for its chassis to deliver excellent bass reproduction in 500W RMS power applications. JL Audio technologies and proprietary assembly designs in the 10W3v3-2 and 10W3v3-4 subwoofers enhance linearity and reliable performance results. The JL Audio 10W3v3 is best used with an amplifier in the 150W - 500W RMS range and is optimized to operate in a compact 0.625 cu. ft. (17.7 l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure. General Specifications Continuous Power Handling 500W RMS Recommended Amplifier Power 150- 500W RMS Nominal Impedance 2Ω JL Audio 10W3v3 Manual
$359.99
W6-Series 10-Inch 600-Watt Subwoofer Driver, 4-Ohm DVC The 10W6v3 subwoofer driver offers several technologies similar to JL Audio's W7AE top line of subwoofers to provide powerful advantages in motor linearity and suspension behavior. This 10" automotive sub has a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. This 10" W6v3 driver is best used with an amplifier in the 200W - 600W RMS range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. The JL Audio 10W6V3-D4 subwoofer driver comes with Dual 4Ω voice coils that allow the 10W6v3 to be installed in a 2Ω or 8Ω configuration. General Specifications Continuous Power Handling 600W RMS Recommended Amplifier Power 200 - 600W RMS Nominal Impedance Dual 4Ω JL Audio 10W6v3 Manual
$799.99
