At this present time our store location is open by appointment only.

150W x 1 @ 4Ω

Amplifiers with a Power Output Rating of 150-Watts x 1-Channels, 4-Ohm Final Impeda

Amplifiers with a Power Output Rating of 150-Watts x 1-Channels, 4-Ohm Final Impedance

RMS power: This rating of any amplifier is the continuous power rating that an amp is designed to output at a maximum continued volume rating. The RMS power specification is one of two numbers to go by when pairing your speakers with an amplifier, not the only 2 but a good starting point. As an example, a speaker driver with a 150-Watt, or 150W for short, RMS rating should be paired with a one-hundre-fifty-watt RMS amplifier. We usually recommend an amp to be over powered by 10% RMS so that the power-plant does not have to work at 100% capacity to get 100-percent efficiency from your speakers. This will keep your amplifier from overheating during long periods of continuous operation.

Ohms: Is the resistance rating of an amp and is the second most important when pairing drivers with amplifiers. A power-plant that is 150W @ 4-ohm might put out 300-Watts @ 2Ω. When purchasing an amplifier, the correct pairing of a speaker’s RMS wattage and Ohm ratings with an amp’s output power rating is absolutely essential.

4 products

  • JL Audio JD250/1 : 250W or 150W Mono Amplifier @ 2Ω or 4Ω JL Audio JD250/1 : 250W or 150W Mono Amplifier @ 2Ω or 4Ω, top side.

    JL Audio JD250/1 : 250W or 150W Mono Amplifier @ 2Ω or 4Ω

    2 Available for pickup

    JD-Series Monoblock Amplifier, 250-Watt @ 2-Ohm or 150-Watt @ 4-Ohm Designed to produce a healthy 250 watts into 2 ohms (14.4V, 1% THD), the JD250/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion. The JD250/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.  The JD250/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you easily set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat. General Specifications @ 4 Ω 150 W RMS x 1 @ 3 Ω 200 W RMS x 1 @ 2 Ω 250 W RMS x 1 Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered JL Audio JD250/1 Manual

    2 Available for pickup

    $229.99

  • Last One! Kicker 46CXA4001t : Mono 300W Amplifier @ 2Ω, or 150W @ 4Ω Kicker 46CXA4001t : Mono 300W Amplifier input section.

    Kicker 46CXA4001t : Mono 300W Amplifier @ 2Ω, or 150W @ 4Ω

    1 Available for pickup

    Mono Amplifier, 300-Watts at 2-Ohm, 150-Watts at 4-Ohm This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash. Efficient Class-D amplifier Three-second turn-on/off delay to eliminate unwanted interference Variable 12dB crossovers provides control to dial in perfect sound KickEQ™ 6dB variable bass boost for those additional low frequencies 24dB subsonic filter for protection from potentially damaging frequencies FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio Accepts up to 40-volt input signal Small footprint for easier installation Vertical mounting hardware included for another unique look This Kicker 46CXA4001t amplifier delivers as much as 400W into one bass channel at 1-Ohm. Specifications MODEL CXA400.1 Power (watts/ch) 4 Ohm 150x1 Power (watts/ch) 2 Ohm 300x1 Power (watts/ch) 1 Ohm 400x1 CXRC Remote Bass Capable (sold sep.) yes Dimensions (in, cm): (all models 2 3/8, 5.9H x 6 3/4, 17W x ...L) 8 1/8, 20.6 Frequency Response (Hz): 25-200, +0/-1dB Input Sensitivity: 250mV-10V (Low Level)1V-40V (High Level) Signal-to-Noise Ratio: >95dB, a-weighted, re: rated power Active Crossover: Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter: 25Hz @24dB/octave KickEQ™ Boost Variable 0-6dB @40Hz Kicker CXA Mono Amplifier Manual

    1 Available for pickup

    $199.99

  • Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm, left side.

    Kicker 47KEY5001 : Mono Amplifier with Built-In DSP, 300W @ 2Ω

    Pre-Order Today!

    Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker. The KEY500.1 delivers 300 watts RMS of power to your speakers at 2-ohms. Measuring less than eight inches long and only two inches high, the KEY500.1 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.  If the temperature reaches the threshold, the Kicker KEY500.1's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption! Specifications Power (watts/ch), 1 Ohm mono 500 Power (watts/ch), 2 Ohm mono 300 Power (watts/ch), 4 Ohm mono 150 Standard dimensions in.(H x W x L) 1-11/16 x 4-1/8 x 8-1/8 Metric dimensions cm(H x W x L) 4.3 x 9.2 x 20.7 Frequency Response (Hz): 10-160 Input Sensitivity: high level: 1V-40V / low level: 125mV-5V Signal-to-Noise Ratio: >90dB, a-weighted, re: rated power Selectable Electronic Crossover: Variable Low Pass 40-160 Hz, Variable High Pass 10-40 Hz What's in the Box: 1 - fuse holder1 - manual and installation hardware Kicker 47KEY5001 Manual

    Pre-Order Today!

    $279.99

  • Skar Audio RP-350.1D : 350W Mono Automotive Amplifier, 350W/250W/150W Mono @ 1Ω/2Ω/4Ω Skar Audio RP-350.1D : 350W Mono Automotive Amplifier, input section.

    Skar Audio RP-350.1D : 350W Mono Automotive Amplifier, 350W/250W/150W Mono @ 1Ω/2Ω/4Ω

    Pre-Order Today!

    RP-Series Monoblock Subwoofer Amplifier 350-Watts @ 1-Ohm, 250-Watts @ 2-Ohm, 150W @ 4-Ohm Skar Audio engineered the RP-350.1D Class D monoblock subwoofer amplifier to be dominant in both power and reliability compared to anything else on the market in its class and physical size. Designing the most efficient, well built, high quality amplifiers is where we start here at Skar Audio, and that is exactly what is delivered in this unit. The smallest of all RP series amplifiers, the RP-350.1D is the perfect solution for when you need versatility but are not willing to sacrifice power output. The RP-350.1D is 1-ohm stable and utilizes a wide array premium internal components that make it extremely powerful and reliable - such as its high speed MOSFET power supply and advanced PCB board layout. Conservatively rated at 350 watts RMS power at a 1-ohm load, with the capabilities of reaching beyond 388 watts at max power output. This compact, small footprint amplifier, is by far one of the most affordable monoblocks Skar Audio has ever released, and is great for powering a pair of subwoofers rated around 200 watts RMS each or a single subwoofer around 400 watts RMS. In addition to all of the above features, the 4 gauge power and ground terminals found on the amplifier allow for maximum current flow and therefore higher power output and more efficient operation. Furthermore, you'll have full reign over your amplifier with the built-in user control panel, featuring a bass EQ switch (0, +6, +12dB), and variable adjustment tunings for gain level, low-pass filter, and subsonic filter. Featuring 4-way protection circuitry, you'll have the peace of mind knowing that you are protected against damage to the amplifier for various reasons - including electrical shortage, over heating, low voltage, and more. This amplifier comes with a remote subwoofer level control (bass knob) allowing the user to have full control over their bass from the front of the vehicle. General Specifications Type Monoblock Car Amplifier Class D Bridgeable No Strappable No Fuse Rating 30 Amp MOSFET Type High Speed MOSFET Power Supply Damping Factor 150< Amplifier Width 6.20" Bass EQ (Boost) Yes (0‚+6 dB‚+12 dB) Output Channels 1 RCA Line Output No Turn-On Circuit Soft Turn-on Circuit Working Voltage 8.5V - 16V Amplifier Height 2.25" Amplifier Length 7.54" Subsonic Control Off - 50Hz Tri-Mode Capable No Frequency Response 20Hz - 250Hz RMS Power at 1 Ohm 350 Watts x 1 Channel (14.4v) Peak Power at 1 Ohm 375 Watts x 1 Channel (14.4v) RMS Power at 2 Ohms 250 Watts x 1 Channel (14.4v) RMS Power at 4 Ohms 150 Watts x 1 Channel (14.4v) Efficiency at 4 Ohms 0.9 Protection Built-in? Yes - 4-Way (Thermal‚Voltage‚Speaker‚DC) Power & Ground Inputs 4 Gauge Signal-to-Noise Ratio 85 dB Low Level Input (Gain) 6V - 0.2mV Low Pass Filter (Variable) 50Hz - 220Hz Power & Protection Indicators Yes - LED Indicators Remote Bass Knob & Cable Included Yes Real World Amplifier Dyno Test Results Dynamic (Peak) Power at 1 Ohm 452 Watts x 1 Channel (14.38v) Certified (RMS) Power at 1 Ohm 378 Watts x 1 Channel (14.36v) Skar Audio RP-Series Amplifier Installation Manual

    Pre-Order Today!

    $189.99

Login

Forgot your password?

Don't have an account yet?
Create account