At this present time our store location is open by appointment only.

150W x 4 @ 2Ω

Amplifiers with a Power Output Rating of 150-Watts x 4-Channels, 2-Ohm Final Impedance

Amplifiers with a Power Output Rating of 150-Watts x 4-Channels, 2-Ohm Final Impedance

RMS power: This rating of any amplifier is the continuous power rating that an amp is designed to output at a maximum continued volume rating. The RMS power specification is one of two numbers to go by when pairing your speakers with an amplifier, not the only 2 but a good starting point. As an example, a speaker driver with a 150-Watt, or 150W for short, RMS rating should be paired with a one-hundred-fifty-watt RMS amplifier. We usually recommend an amp to be over powered by 10% RMS so that the power-plant does not have to work at 100% capacity to get 100-percent efficiency from your speakers. This will keep your amplifier from overheating during long periods of continuous operation.

Ohms: Is the resistance rating of an amp and is the second most important when pairing drivers with amplifiers. A power-plant that is 150W @ 2-ohm might only put out 75-Watts @ 4Ω. When purchasing an amplifier, the correct pairing of a speaker’s RMS wattage and Ohm ratings with an amp’s output power rating is absolutely essential.

1 product

  • JL Audio MHD600/4-24V : 4ch 24V Marine Amplifier, 150W x 4 @ 1.5-4Ω JL Audio MHD600/4-24V : 4ch 24V Marine Amplifier, top side.

    JL Audio MHD600/4-24V : 4ch 24V Marine Amplifier, 150W x 4 @ 1.5-4Ω

    Pre-Order Today!

    MHD-Series 4-Channel Class-D 24-Volt Marine Grade Amplifier, 150-Watts x 4ch @ 1.5-4-Ohms This compact, multi-channel powerhouse employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 150W x 4ch or 300W x 2ch's. Tight power supply regulation keeps distortion down and maximizes sound quality. The MHD600/4-24V is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. It can also be deployed, on its own, as a very capable 3-channel system amplifier with 150W x 2ch to the satellites and 300W x 1 to a subwoofer system. This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment. This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24 V may result in damage to the product and will void the warranty. Specifications @ 4 Ω 150 W RMS x 4 @ 3 Ω 150 W RMS x 4 @ 2 Ω 150 W RMS x 4 @ 1.5 Ω 150 W RMS x 4 Bridged @ 8 Ω 300 W RMS x 2 Bridged @ 4 Ω 300 W RMS x 2 Frequency Response 6 Hz - 30 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >110 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >88.2 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >300 / 50 Hz Damping Factor @ 2 Ω >150 / 50 Hz THD+N @ Rated Power <0.03% @ 4 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS to 800 mV - 8 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 25 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional (HD-RLC) Remote Level Modes 2 or All Channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes JL Audio MHD600/4-24V Manual

    Pre-Order Today!

    $1,449.99

Login

Forgot your password?

Don't have an account yet?
Create account