MX-Series 500-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 300W @ 4-Ohm
Engineered specifically for powersports applications, the MX500/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 500W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX500/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 12 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>97 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>70 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>115 / 50 Hz
Damping Factor @ 2 Ω
>54 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
300 W RMS x 1
@ 3 Ω
400 W RMS x 1
@ 2 Ω
500 W RMS x 1
@ 1.5 Ω
N/A
JL Audio MX500/1 Manual
Mono Amplifier, 600-Watts at 2-Ohm, 300-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA8001t amplifier delivers as much as 600W into one bass channel.
Specifications
MODEL
CXA800.1
Power (watts/ch) 4 Ohm
300x1
Power (watts/ch) 2 Ohm
600x1
Power (watts/ch) 1 Ohm
800x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)8-1/8, 20.6
Frequency Response (Hz):
25-200, +0/-1dB
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
>95dB, a-weighted, re: rated power
Active Crossover:
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter:
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
