100W x 2 @ 2Ω

Amplifiers with a Power Output Rating of 100-Watts x 2-Channels, 2-Ohm Final Impedance

Amplifiers with a Power Output Rating of 100-Watts x 2-Channels, 2-Ohm Final Impedance

RMS power: This rating of any amplifier is the continuous power rating that an amp is designed to output at a maximum continued volume rating. The RMS power specification is one of two numbers to go by when pairing your speakers with an amplifier, not the only 2 but a good starting point. As an example, a speaker driver with a 100-Watt, or 100W for short, RMS rating should be paired with a one-hundred-watt RMS amplifier. We usually recommend an amp to be over powered by 10% RMS so that the power-plant does not have to work at 100% capacity to get 100-percent efficiency from your speakers. This will keep your amplifier from overheating during long periods of continuous operation.

Ohms: Is the resistance rating of an amp and is the second most important when pairing drivers with amplifiers. A power-plant that is 100W @ 2-ohm might only put out 50-Watts @ 4Ω. When purchasing an amplifier, the correct pairing of a speaker’s RMS wattage and Ohm ratings with an amp’s output power rating is absolutely essential.

1 product

  • JL Audio MX600/3 : 3ch Marine Amplifier, 75W x 2 + 400W Mono @ 2Ω JL Audio MX600/3 : 3ch Marine Amplifier, top side.

    JL Audio MX600/3 : 3ch Marine Amplifier, 75W x 2 + 400W Mono @ 2Ω

    Pre-Order Today!

    MX-Series 75-Watts x 2-Channel Class-D Marine-Grade Amplifier + 400-Watt Subwoofer Out @ 2-Ohm Engineered specifically for powersports applications, the 3-channel MX600/3 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. Generating a solid 75W x 2 into 4 ohms (14.4V, 1% THD), the MX600/3 is the perfect solution for driving a pair of speakers and a subwoofer. Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 20 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >92 / 50 Hz Damping Factor @ 2 Ω >43 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 580 mV - 14 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™) Main Channels @ 4 Ω 75 W RMS x 2 Main Channels @ 2 Ω 100 W RMS x 2 Main Channels - Bridged @ 4Ω 200 W RMS x 1 Subwoofer Channel @ 4 Ω 250 W RMS x 1 Subwoofer Channel @ 3 Ω 300 W RMS x 1 Subwoofer Channel @ 2 Ω 400 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A JL Audio MX600/3 Manual

    Pre-Order Today!

    $499.99

Login

Forgot your password?

Don't have an account yet?
Create account