100W x 4 @ 2Ω

AM-Series Marine-Grade 4-Channel Amplifier, 100-Watt @ 2-Ohm or 65-Watt @ 4-Ohm The FUSION AM Series marine amplifiers are purpose-built for the marine environment. Boasting some of the most impressive environmental protection available, they deliver performance on the water like never before. With 4 channels and a 500 Watt peak power output, the MS-AM504 will power either a pair of Fusion speakers plus a 10” subwoofer, or up to four pairs of speakers (with 2 speakers in parallel each channel at 2 Ohms), to spread the sound around your vessel. Incorporating heat-tempered and conformal coated PCBs for maximum product life, and gold-plated connectors for improved signal flow, the MS-AM504 reproduces clean and powerful audio with enough power to rock the boat. Features: 500W peak power output to power up to eight speakers Class-AB amplifier – power efficient with less cross-over distortion Conformal coated PCBs – water resistant protection from salt air and moisture FUTRANZ heat sink technology – transfers heat more efficiently and provides more thermal stability with maximum component reliability F.R.A.T (Fusion Regulated Amplifier Technology) – provides enormous power output at low voltage. F.I.S.T (Fusion Intercooled Semi-Conductor Technology) – clamps down internal power switching to rapidly remove heat from all associated semi-conductors 1 year limited Consumer Warranty The Fusion AM Series marine amplifiers are the perfect complement to any Fusion marine stereo system. Product Specifications Amplifier Class Class-AB Frequency Response 5Hz - 38kHz +/- 3dB Peak Power 500 Watts Rated Power (4 Ohms) 65 Watts RMS x 4 @ 14.4V - 4Ω 1% THD Rated Power (2 Ohms) 100 Watts RMS x 4 @ 14.4V - 2Ω 1% THD Rated Power (4 Ohms Bridged) 200 Watts RMS x 2 @ 14.4V - 4Ω Bridged 1% THD Mounting Dimensions Length 366mm [14-7/16"] Depth 229mm [9"] Height 53mm [2-1/16"] Fusion AM504 Manual

Read more less

M-Series 4-Channel Class-D Full-Range Marine-Grade Amplifier, 75-Watts x 4-Channel @ 4-Ohm This tiny amplifier packs a serious full-range punch, delivering a staggering 100W to each of its four channels into 2Ω (14.4V, 1% THD). The breakthrough that makes this much power possible in such a small chassis is JL's NexD™ ultra-high-speed switching design, which allows for full bandwidth Class D operation with extremely low distortion and outstanding efficiency. Use the M400/4 in combination with JL's M600/1 monoblock to build a 1000W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat. Or, use the M400/4 by itself to power two satellites, plus a subwoofer. With M-Series amplifier, the possibilities are endless. The M400/4 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an HD-RLC remote level control (sold separately), the amplifier's Ch. 1 & 2 level or overall level can be directly controlled from a remote location. This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment. Specifications @ 4 Ω 75 W RMS x 4 @ 2 Ω 100 W RMS x 4 Bridged @ 4Ω 200 W RMS x 2 Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 100 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 40 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional (HD-RLC) Remote Level Modes 2 or All channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes JL Audio M400/4 Manual

Read more less

XDM-Series Five-Channel Class-D Marine-Grade Amplifier, 75-Watts x Four-Channels @ 4-Ohm and 600-Watt Mono @ 2-Ohm The XDM1000/5 delivers up to 1000W of clean power and is ideal for an audiophile-grade, subwoofer + four satellite system. With this potent powerhouse, you can drive two pairs of quality component speaker systems with plenty of clean power (75W x 4 @ 4Ω), while also generating a stout 600W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's high-speed NexD switching amplifier design. Suitable for car or boat installations, the XDM1000/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM1000/5 includes a 12dB / octave high-pass filter for one main channel pair, a 12dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500Hz or 500-5000Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications Main Channels @ 4 Ω 75 W RMS x 4 @ 14.4V Main Channels @ 2 Ω 100 W RMS x 4 @ 14.4V Main Channels - Bridged @ 4Ω 200 W RMS x 2 @ 14.4V Subwoofer Channel @ 4 Ω 400 W RMS x 1 @ 14.4V Subwoofer Channel @ 3 Ω 500 W RMS x 1 @ 14.4V Subwoofer Channel @ 2 Ω 600 W RMS x 1 @ 14.4V Subwoofer Channel @ 1.5 Ω N/A Main Channels @ 4 Ω 60 W RMS x 4 @ 12.5V Main Channels @ 2 Ω 90 W RMS x 4 @ 12.5V Main Channels - Bridged @ 4Ω 180 W RMS x 2 @ 12.5V Subwoofer Channel @ 4 Ω 360 W RMS x 1 @ 12.5V Subwoofer Channel @ 3 Ω 480 W RMS x 1 @ 12.5V Subwoofer Channel @ 2 Ω 600 W RMS x 1 @ 12.5V Subwoofer Channel @ 1.5 Ω N/A Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 5 kHz Filter Mode(s): Channels 3 & 4 (rear) High-Pass or Bandpass Filter Slope(s): Channels 3 & 4 (rear) 12 dB/octave Filter Frequency Range: Channels 3 & 4 50 Hz - 500 Hz Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A Height (H) 2.05 in / 52 mm Width (W) 14.73 in / 374 mm Depth (D) 7.09 in / 180 mm JL Audio XDM1000/5v2 Manual

Read more less

XDM-Series Four-Channel Class-D Marine-Grade Amplifier, 100-Watts x Four-Channels @ 2-Ohm or 75-Watts x 4-Channels @ Four-Ohm The ultra-compact XDM400/4 packs a serious full-range punch, generating a whopping 100-watts to each of its four channels into 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD high-speed switching design, which permits full bandwidth Class-D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM400/4 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Combine the XDM400/4 with our XDM600/1 monoblock to build a stunning 1000W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat or deck. Or, use the XDM400/4 by itself to power two satellites, plus a subwoofer.  The XDM400/4 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the rear channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 75 W RMS x 4 @ 14.4V @ 2 Ω 100 W RMS x 4 @ 14.4V Bridged @ 4Ω 200 W RMS x 2 @ 14.4V @ 4 Ω 60 W RMS x 4 @ 12.5V @ 2 Ω 90 W RMS x 4 @ 12.5V Bridged @ 4Ω 180 W RMS x 2 @ 12.5V Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 40 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or All channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or All channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes JL Audio XDM400/4v2 Manual

Read more less

XDM-Series Five-Channel Class-D Marine-Grade Amplifier, 75-Watts x Four-Channels @ 4-Ohm and 300-Watt Mono @ 2-Ohm The XDM700/5 is ideal for a complete audiophile-grade, subwoofer + four satellite system, and fits comfortably in just about any vehicle or vessel. With this incredible little amplifier, you can drive two pairs of quality component speaker systems with plenty of clean power (75W x 4 @ 4Ω), while also generating a solid 300W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's high-speed NexD switching amplifier design. Suitable for car or boat installations, the XDM700/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM700/5 includes a 12dB / octave high-pass filter for one main channel pair, a 12dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500Hz or 500-5000Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications Main Channels @ 4 Ω 75 W RMS x 4 @ 14.4V Main Channels @ 2 Ω 100 W RMS x 4 @ 14.4V Main Channels - Bridged @ 4Ω 200 W RMS x 2 @ 14.4V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 14.4V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 14.4V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 14.4V Subwoofer Channel @ 1.5 Ω N/A Main Channels @ 4 Ω 60 W RMS x 4 @ 12.5V Main Channels @ 2 Ω 90 W RMS x 4 @ 12.5V Main Channels - Bridged @ 4Ω 180 W RMS x 2 @ 12.5V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 12.5V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 12.5V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 12.5V Subwoofer Channel @ 1.5 Ω N/A Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™) Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 5 kHz Filter Mode(s): Channels 3 & 4 (rear) High-Pass or Bandpass Filter Slope(s): Channels 3 & 4 (rear) 12 dB/octave Filter Frequency Range: Channels 3 & 4 50 Hz - 500 Hz Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 6.15 lb / 2.79 kg JL Audio XDM700/5 Manual

Read more less