Alpine

A premium sound system for your Jeep Wrangler JK Unlimited is. The PSS-22WRA is a 1200-watt, 9-speaker sound system for 2011-2018 Jeep Wrangler JK Unlimited, providing excellent sound performance with the top on or off.  Caught with the top off in inclement weather? Not to worry.  The PSS-22WRA is IP55 rated, so it can withstand rain and dust. The subwoofer uses rust resistant hardware and can handle water from off-roading adventures or a quick rinse down.  The PSS-22WRA’s subwoofer and amplifier don’t take up any usable space since they mount under the passenger’s seat for an easy bolt-in installation with simple wire routing. All necessary installation accessories are included.  The included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-22WRA is compatible with any Alpine Restyle Jeep Wrangler dash system, the Jeep factory base radio, or other aftermarket radio. Specifications Direct fit weather resistant (IP55) speaker package for non-amplified 2011– 2018 4-door Jeep® Wrangler JK Unlimited 600W RMS System SPV-65X-WRA 6.5-inch Convertible Component/Coax water resistant speaker kit SBV-10-WRA 10-inch under passenger seat water resistant enclosed subwoofer KTA-30FW – 75W X 4ch Water Resistant Amplifier KTA-30MW – 300W Water Resistant Mono Amplifier Plug & play sound system Compatible with an Alpine Restyle In-Dash system, aftermarket head unit, or with the factory Jeep radio Includes remote bass knob, vehicle specific harnesses and mounting brackets Alpine PSS-22WRA Manual

Read more less

R-Series 10-Inch 750-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Dual Voice Coil Since the Type R platform, Alpine’s R-Series sound system family has been known for its incredible output and reliable performance. Now Alpine introduces the next-generation of sound performance with the 2nd-Gen R-Series Subwoofers with even more bass output. The 2nd-Gen R-Series Subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control from the subwoofer cone compared to the previous generation. An integrated Faraday ring minimizes distortion for cleaner bass output. A Kevlar-treated cone ensures durability in the subwoofer for reliable performance, even at high volumes. A new polypropylene/ceramic composite dust cap ensures rigidity while also providing incredible internal damping (vibration absorption) to smooth out the bass response and reproduce tight bass. This premium, unique material also has higher heat reliability that ensures non- stop bass performance. The 2nd-Gen R-Series Subwoofers contain a Dual Voice Coil (DVC) with easy configuration jumpers that allow for flexible applications. A new “EZ- Change” twist-lock grille mounting system makes it easy to install and remove an optional grille without mounting screws for added protection to the cone. The R2-W10D2 and R2-W10D4 is compatible with the KTE-10G Grille System (sold separately). The 2nd-Gen R-Series Subwoofers contain Alpine’s High Amplitude Multi- Roll (HAMR) Surround Technology. This rubber surround allows the subwoofer cone to efficiently move air while staying cool. This technology allows for 20mm of total cone excursion and motion that creates incredible accuracy from the subwoofer. Features Dual Voice Coil (DVC) Subwoofers with Configuration Jumpers Polypropylene/Ceramic Composite Dust Cap  Kevlar Reinforced Pulp Cone High-Performance subwoofers   Twist-Lock Grille Mount System  High-Amplitude Multi-Roll (H.A.M.R.) Surround  Large Double-Stacked Magnets Specifications 750W RMS  2250W Peak Power Handling  Frequency Response: 26Hz-200Hz  Sensitivity (1W/1m): 82.4dB   Nominal Impedance: 4Ω Voice Coil: 65mm   X-Max: 20mm Magnet Weight: 123oz  Mounting Depth: 6” (152mm) Cutout Size: 9-1/16” (231mm) Push-Type Speaker Terminals (Up to 8AWG Wire Size) CTA-2031 Compliant  Alpine R2-W10D Manual

Read more less

R-Series Loaded 600-Watt Thin 10-Inch 2-Ohm Subwoofer Enclosure Now you don’t have to choose between bass and space! Alpine’s R-Series Shallow preloaded subwoofer enclosure measures at a minimal 5.25” deep to deliver a loud and fun sound in most vehicle applications. Rubber “feet” are adjustable in height to accommodate uneven vehicle floors. Don’t let the size fool you – the enclosures feature the same motor movement (20MM of 1-way excursion) as the full-size R2-Series subwoofers for extreme output in a shallow woofer design. At the heart of the R-Series shallow subwoofers is an oversized 4-inch voice coil that houses the lightweight and powerful neodymium magnet for 600W RMS of power handling. Integrated cooling fins located in the core of the subwoofer help dissipate the heat generated by the rapid subwoofer movement for enhanced cooling reliability and hours of uninterrupted playtime. The unique CoolMount dual-panel mount subwoofer motor enhances cooling. Alpine’s Gen2 DD-Linear Magnetic Circuit technology, a compact and efficient dual-gap voice coil structure, allows for better control over the motor, resulting in lower distortion and precise bass control. The preloaded enclosures use the subwoofer frame as bracing fora more ridged design and better bass response. A lightweight yet rigid aluminum dust cap allows the R-Series shallow subwoofer to transition sound quickly with minimal distortion and project the bass off the surface of the speaker for hard-hitting yet smooth bass performance. The included adjustable mounting brackets allow for a downfire mount configuration. With dual voice coils wired in parallel for a 2Ω load, the Alpine R-Series 10" shallow subwoofer enclosure is optimized to perform with Alpine's S-A60M or R-A75M mono amplifiers. Features Optimal sealed cabinet quality   Aluminum Dust Cap Neodymium Magnet    Alpine Gen2 DD Linear Magnetic Circuit   CARB compliant ¾” MDF construction   Premium Alpine embroidered black carpet  Alpine-branded terminal cup  Pre-installed steel mesh grille  Includes a 10” R-Shallow Subwoofer (RS-W10D4) Rubber, modular stackable foot design Specifications Dimensions: 21.15” W x 5.25” H x 16” L 600W RMS Power Handling  Frequency response: 29Hz – 200Hz  Dual 4Ω voice coils wired in parallel for a 2Ω load (compatible with S-A60M or R-A75M)  Nominal Impedance: 2Ω  Voice Coil: 4”(101.6mm)

Read more less

Alpine S-Series 600-Watt 10-Inch Subwoofer Driver, 2Ω or 4Ω Dual Voice Coil Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. Specifications 10" DVC High Performance Subwoofer Power Handling: 600W RMS/1800W Peak Push-type Insert Terminals with DVC jumper system Concealed Mount Gasket/Grille* System (*Grille sold separately) Frequency Response: 28Hz-200Hz Mounting Depth 4-11/16” Alpine S-W10D2, S-W10D4 Manual

Read more less

Alpine 350-Watt 10-Inch Truck Subwoofer Enclosure, 2Ω Final Impedance With a compact wedge-style design and shallow mount, the SBT-S10V (2-ohm system) is a perfect fit for truck applications, with a design that works in small spaces. Radial Vented VC Heat Sink & Airflow Management System actively manages voice coil temperatures by forcing air directly across the heat sink system. FEA Optimized Dual-Sided Machined CRC Motor Structure creates a symmetrical magnetic field with evenly distributed flux density to greatly reduce distortion, while further improving power handling and output. The High-Amplitude Multi Roll Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene ®, the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions. Specifications 2Ω Impedance Ported Enclosure Design Frequency Response: 28Hz-200Hz Dimensions 21-5/8" Wide x 15-1/4" Tall x 7-1/4" Deep 1x 3-15/16" Alpine SBT-S10V Manual

Read more less

Alpine 350-Watt Loaded 10-Inch Subwoofer-Enclosure for 2007-2018 Jeep-Wrangler JK-Unlimited, 2Ω Final Impedance When you have a Wrangler, you don’t have extra space to spare. Alpine engineered the SBV-10-WRA to conveniently fit under the front passenger’s seat making efficient use of space. The SBV-10-WRA is a custom-shaped enclosure that fits snugly under the seat frame, so no mounting hardware is required. (NOTE: designed for fitment in Jeeps with the factory carpet. Fitment is not guaranteed with aftermarket or removed carpet) Enjoy impactful bass, with your Wrangler’s top on or off. The SBV-10-WRA loads the lower frequency sound into the passenger’s foot well to deliver quality sound and maximized bass extension at all times, so your music continues even when the asphalt ends. Specifications 10” Pre-loaded Sealed Custom-fit Enclosure Weather Resistant (IP66 rating) Power Handling: 350WRMS/1050W Peak Nominal Impedance 2Ω Frequency Response: 45-200Hz OEM-grade Molex 2-pin connector w/pigtail wire harness Alpine SBV-10-WRA Manual

Read more less

Alpine 350-Watt Thin 10-Inch Subwoofer Driver, 2Ω or 4Ω Impedance The SWT 10” Truck Subwoofer has been engineered to offer more installation flexibility without sacrificing big output to build the ideal sound system for your truck. At 4-1/8” deep, these subs provide deep bass performance where it normally couldn’t fit in a truck. And the vented pole optimized for 4-1/8” deep box is the ideal enclosure size meaning great bass performance can fit just about anywhere in your truck. The FEA-Optimized Motor Structure together with Alpine's revolutionary High-Amplitude Multi Roll (HAMR) Suspension Design gives the new SWT Truck Subwoofers the highest X-max and SPL output in its category. The new SWT Truck Subwoofers deliver the best-in-class bass output, ultra-low distortion, and unparalleled sound quality. With a real world, measured 11mm of X-max, the SWT subwoofers perform like traditional models, yet fit in smaller spaces. 4 UNIQUE ALPINE TECHNOLOGIES Radial Vented VC Heat Sink & Airflow Management SystemActively manages voice coil temperatures by forcing air directly across the heat sink system. FEA Optimized Dual-Sided Machined CRC Motor StructureCreates a symmetrical magnetic field with evenly distributed flux density to greatly reduce distortion, while further improving power handling and output. FEA Optimized Injection Molded TPE Spider with Pass-Through Gap DesignProvides the mechanical clearance needed for over 50mm of peak-to-peak excursion, unleashing massive output potential from a small package FEA Optimized HAMR SurroundThe High-Amplitude Multi Roll Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene ®, the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions. Specifications 350W RMS, 1000W Peak Power Handling Frequency Response: 30Hz-200Hz Mounting Depth 4-3/16" 2Ω or 4Ω Voice Coil

Read more less