Car Audio Collection

C1-Series 6.5-Inch 50-Watt Component Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C1-650 Manual

Read more less

C1-Series 6x9-Inch 60-Watt Component Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690 is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, 1-inch aluminum dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB JL Audio C1-690 Manual

Read more less

Alpine 6X9-Inch Component 2-Way Speakers, 85-Watt RMS Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S69C 6x9” Component Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra- High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry- level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S69C is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. Experience a fuller and richer sound with the S2-S69C's unique 3" midrange speakers with built-in 3/4" tweeters. Designed to capture the midrange frequencies present in vocals and acoustic instruments, this added midrange speaker enhances your music like never before. Alpine-exclusive High Amplitude Multi- Roll (HAMR) surround technology is integrated into the speaker design which allows for maximum cone movement, delivering powerful and accurate bass notes. The S-Series S2-S69C is compatible with the KTE-S69G Speaker Grille (sold separately). This sleek and stylish grille will not only add a visual upgrade to your speakers but also provide protection against any damage. Specifications Hi-Res Audio Certified (Up to 40kHz) Poly Propylene, Glass Fiber, and Mica Cone Material Lightweight Design with High Output and Low Distortion High-Amplitude Multi-Roll (H.A.M.R.) Surround   Included 3” Mid-Range with built-in 3/4" Tweeter (Coaxial) OEM Fitment with In-Line Crossovers Compatible with KTE-S69G Speaker Grille (sold separately) Woofer Size: 6x9” Mid-Range/Tweeter: 3" with built-in 3/4” Tweeters (Coaxial) Power Handling: 85W RMS / 260W Peak Frequency Response: 65Hz - 40kHz (Hi-Res) Sensitivity: 90dB

Read more less

C3-Series 6.5-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650 system features 6.5-inch (165 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-650 Manual

Read more less

Alpine 6-1/2-Inch Component 2-Way Speakers, 80-Watt RMS Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65C 6.5” Component Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra- High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry- level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. Alpine-exclusive High Amplitude Multi- Roll (HAMR) surround technology is integrated into the speaker design which allows for maximum cone movement, delivering powerful and accurate bass notes. Engineered for versatility, these speakers offer seamless OEM fitment and simplified installation. With in-line crossovers, you can achieve optimal sound separation and precise tuning. The adjustable tweeters feature a flush mount housing that is removable allowing for installations in small OEM tweeter locations. The S-Series S2-S65 is compatible with the KTE-S65G Speaker Grille (sold separately). This sleek and stylish grille will not only add a visual upgrade to your speakers but also provide protection against any damage. Specifications Hi-Res Audio Certified (Up to 40kHz) Poly Propylene, Glass Fiber, and Mica Cone Material Lightweight Design with High Output and Low Distortion High-Amplitude Multi-Roll (H.A.M.R.) Surround   Included 1” Adjustable Tweeters with Threaded Removable Housing (Component) OEM Fitment with In-Line Crossovers Compatible with KTE-S65G Speaker Grille (sold separately) Woofer Size: 6.5”  Tweeter Size: 1” (Component) Power Handling: 80W RMS / 240W Peak Frequency Response: 70Hz - 40kHz (Hi-Res) Sensitivity: 88dB

Read more less

6x9-Inch 125-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 6x9" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 125 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 6x9, 160x230 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-150 Sensitivity [1W, 1m] 92 Frequency Response [Hz] 35-21k Woofer Mounting Hole Diameter [in, mm] 5-5⁄8x8-7⁄16, 143x215 Woofer Bottom Mount Depth [in, mm] 2-15⁄16, 75 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

Read more less

6.5-Inch 125-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 6.5" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 125 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 6-½, 160 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-125 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 35-21k Woofer Mounting Hole Diameter [in, mm] 4-13⁄16 , 123 Woofer Bottom Mount Depth [in, mm] 1-13⁄16 , 46 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

Read more less

Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The Next-Generation R-Series speakers now come in upgraded 'Pro' models in addition to the standard model lineup. The pro models utilize a highly rigid, die-cast aluminum basket that eliminates flexing and resonance during playback to ensure the highest quality sound performance. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65C is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

Read more less

Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65C is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade In-Line Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

Read more less

C2-Series 6.5-Inch Component Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs. The C2-650 system features 6.5-inch (165 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-650 Manual

Read more less

C6-Series 6.5-Inch 75-Watt Component Audiophile Speaker System Born from shared technologies used in JL's flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features: Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding mid-bass impact, linearity and low distortion Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels Cast alloy frame with JL's Elevated Frame Cooling feature Includes fine mesh grilles C6 Tweeter Features: Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping Neodymium motor delivers high magnetic flux from a compact motor design Ferrofluid cooling and damping improves reliability and response smoothness Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz – 21 KHz ± 3 dB JL Audio C6-650 Manual

Read more less

Hybrid Series 6-1/2" 140-Watt RMS 2-Way Component Door Speakers Embracing Morel’s legendary craftsmanship, engineering, and innovation, the latest Hybrid systems define an ever-evolving concept of high-fidelity speaker design. Now in their fifth generation, the new Hybrid and Hybrid Integra systems give a further refined listening experience, captivating you with the raw emotions of listening to live music. Their subtle balance of resolution, power, and efficiency has been further optimized to exceed expectations regardless of what genre of music you enjoy. Now the Hybrid is available in 2-way and Integra point source (coaxial) solutions, as well as a new 3-way system to fit nearly any system requirement.  CONTROLLED ACOUSTIC RESISTANCEThe C.A.R. Filter™ improves the acoustic loading by controlling airflow within the driver, mimicking the effects of a cabinet while improving power handling by 30%. This provides greater control over the cone movement for improved bass dynamics. EVC MOTORMorel speakers with EVC™ technology utilize voice coils that are up to three times larger than those used in conventional loudspeakers, enabling improved heat dissipation, power handling and linearity. The EVC™ design moves the magnetic motor system to within the voice coil, eliminating stray magnetic flux by effectively directing all the magnetic energy to the voice coil. The EVC architecture is over 90% more efficient than conventional design, magnetically shielded, and highly compact. HANDCRAFTED ACUFLEX SOFT DOMEA specially engineered damping compound hand-applied to the soft domes, adding rigidity and damping, which greatly improves the clarity and bandwidth of the tweeter/mid-range. The Acuflex™ diaphragm exhibits controlled cancelling break up (accurate–flexing), meaning each break-up mode is counteracted by another in the opposite direction, enabling smooth frequency response. HEXATECH™ ALUMINIUM VOICE COILMade from 100% aluminum wire shaped like a honeycomb, the Hexatech™ voice coil reduces air gaps in the coil windings, thereby increasing efficiency by up to 20%. Being lightweight, Hexatech™ voice coils are largely responsible for the extraordinary fast transient response Morel drive units are known for. HYBRID MAGNET MOTORThe Hybrid motor drive system uses a ferrite magnet together with a very powerful neodymium magnet. Combined they create a compact, lightweight motor system that is up to four times more powerful than conventional designs of the same size. With Hybrid, more amplified power is converted into sonic energy for flawless performance, even in a small driver. PAPER CONEIn use since the first loudspeakers, the paper continues to be an exceptional material of choice. Morel’s latest paper composite cones are ultra-lightweight, making them an exceptional pairing for drivers using smaller motors and voice coils. Sold by the Pair Specifications MODEL SIZE & CONFIGURATION POWER HANDLING (WRMS) / PEAK POWER (W) SENSITIITY (2.83V/1M)(DB) FREQUENCY RESPONSE (HZ) CROSSOVER HYBRID 42 4" 2-way 100 / 300 89 50-25000 MXR240.4 HYBIRD 52 5¼" 2-way 120 / 500 90 45-25000 MXR240.4 HYBRID 62 6½" 2-way 140 / 600 91 35-25000 MXR240.4 Morel Hybrid Series Door Speaker Manual

Read more less

Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applic The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S69 is a standard coaxial speaker set that includes a 6x9” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6x9” Mid-Bass with 1” Tweeter Frequency Response: 60Hz -40kHz  Power Handling: 100W RMS / 300W Peak

Read more less

Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The Next-Generation R-Series speakers now come in upgraded 'Pro' models in addition to the standard model lineup. The pro models utilize a highly rigid, die-cast aluminum basket that eliminates flexing and resonance during playback to ensure the highest quality sound performance. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. Magnesium, hard-dome tweeters contribute to the “loud and fun” R-series sound signature and feature a swivel- mount design for optimal listening positioning and threaded removable housing for flexible factory applications. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S652 is a standard component speaker set that includes a 6.5” Mid-Range and 1” Tweeter with an outboard crossover network the professional installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

Read more less

Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-653S features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-653S has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-653S is a custom-fit model that includes a 6.5- inch Mid-Bass driver, a 3.5-inch Midrange driver, and 1.25-inch High-Range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 3.5" Midrange Driver (8.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-653S Manual

Read more less

Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-653 features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-653 has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-653 is a custom-fit model that includes a 6.5- inch Mid-Bass driver, a 3.5-inch Midrange driver, and 1.25-inch High-Range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 3.5" Midrange Driver (8.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-653 Manual

Read more less

Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65CS features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65CS has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65CS is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65CS Manual

Read more less

Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65C features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65C has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65C is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is soldseparately and can be used to build acustom sound system. Three sets of true4V preamp outputs are included to add needed. For best results, install the additional amplifiers if more power iscomplete Alpine Status system togetheras a full system to achieve the highestin-class audio performance only second to the Ultra Hi-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1.25” High Range Driver (3.2cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65C Manual

Read more less

6x8-Inch 100-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 6x8" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 100 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 6x8, 160x200 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-100 Sensitivity [1W, 1m] 91 Frequency Response [Hz] 35-21k Woofer Mounting Hole Diameter [in, mm] 5x7-1⁄8, 127x182 Woofer Bottom Mount Depth [in, mm] 2-¼, 58 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

Read more less

5.25-Inch 100-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 5.25" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 100 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 5-¼, 130 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-100 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 38-21k Woofer Mounting Hole Diameter [in, mm] 4-½, 115 Woofer Bottom Mount Depth [in, mm] 1-¾, 45 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

Read more less

6.75-Inch 125-Watt Component or Coaxial Mountable Speaker System Kicker KS-Series door-speakers let you play at concert-like volume while pleasing even the most selective ear. Internally dampened polypropylene cones and durable rubber surrounds assist the woofers in creating precise midrange and bass, while high-quality silk-dome tweeters deliver natural, detailed highs. These 6.75" Kicker speakers component system with separate tweeters, or convert them to a coaxial system. The woofers’ removable bullet-style phase plug is replaced with a special adapter, allowing the 25 millimeter, silk-dome tweeters to rotate and tilt. You get more system design options and superior off-axis performance. They work best with 15 to 125 watts of recommended power. See below for more details. High power handling Silk-dome tweeters for a smooth sound Polypropylene woofer and tough rubber surrounds Thin-mount design easily fits behind factory grilles Four tweeter mounting options Articulating tweeter pod included Smaller crossover makes mounting even easier Grilles included Specifications Woofer [in, mm] 6-¾, 165 Tweeter [in,mm] 1, 25 Dome Material Silk Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-125 Sensitivity [1W, 1m] 91 Frequency Response [Hz] 35-21k Woofer Mounting Hole Diameter [in, mm] 5-9⁄16 , 141 Woofer Bottom Mount Depth [in, mm] 1-13⁄16 , 46 Flush Mount Tweeter Hole Diameter [in,mm] 1-¾, 45 Flush Mount Tweeter Depth [in,mm] 11⁄16 , 17 High Pass [dB], at Frequency [Hz] 12, 4,000 Low Pass [dB], at Frequency [Hz] none High Frequency Output Attenuation [dB] 0, 4.5, 9 Kicker KS Series Component Speaker Manual

Read more less

6.5-Inch 90-Watt RMS Convertible Component Automotive Door Speakers The 6.5" QS series audiophile component door speakers by Kicker offer stunning midrange drivers, audiophile precise tweeters and a superior crossover network. The QS 6-1/2 Inch convertible speakers are a matched component system, built for pure sonic reproduction.  The Kicker 41QSS654 crossovers allow you to use a single amplifier channel, or use bi-amplification for even more flexibility and control. These 6.5" QS series convertible speakers can be installed as a pair of components or a coaxial configuration. These Kicker speakers work best with 90 watts of recommended power. See below for more details. Specifications Woofer (in., mm) 6 1/2, 160 Tweeter (in., mm) 1 3/16, 30 Tweeter dome material Tetoron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 90 Peak Power (watts, per ANSI/CTA-2031-A) 180 Sensitivity [1W, 1m] 86dB Frequency Response [Hz] 50 - 22k Woofer Mounting Hole Diameter [in, mm] 5 1/16, 129 Woofer Bottom Mount Depth [in, mm] 2 1/2, 63.5 Flush Mount Tweeter Hole Diameter [in,mm] 1 13/16, 46 Flush Mount Tweeter Depth [in,mm] 1 1/8, 29 High Pass [dB], at Frequency [Hz] 24, 2800 Low Pass [dB], at Frequency [Hz] 12, 2800 High Frequency Output Attenuation [dB] 0, +3, +6 Kicker QSS Series Manual

Read more less

6.75-Inch 100-Watt RMS Convertible Component Automotive Door Speakers The 6.75" QS series audiophile component door speakers by Kicker offer stunning midrange drivers, audiophile precise tweeters and a superior crossover network. The QS 6-3/4 Inch convertible speakers are a matched component system, built for pure sonic reproduction.  The Kicker 41QSS674 crossovers allow you to use a single amplifier channel, or use bi-amplification for even more flexibility and control. These 6.75" QS series convertible speakers can be installed as a pair of components or a coaxial configuration. These Kicker speakers work best with 100 watts of recommended power. See below for more details. Specifications Woofer (in., mm) 6-3/4, 165 Tweeter (in., mm) 1-3/16, 30 Tweeter dome material Tetoron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 100 Peak Power (watts, per ANSI/CTA-2031-A) 200 Sensitivity [1W, 1m] 87dB Frequency Response [Hz] 40-22k Woofer Mounting Hole Diameter [in, mm] 5-7/16, 138 Woofer Bottom Mount Depth [in, mm] 2-1/2, 63.5 Flush Mount Tweeter Hole Diameter [in,mm] 1-13/16, 46 Flush Mount Tweeter Depth [in,mm] 1-1/8, 29 High Pass [dB], at Frequency [Hz] 24, 2800 Low Pass [dB], at Frequency [Hz] 12, 2800 High Frequency Output Attenuation [dB] 0, +3, +6 Kicker QSS Series Manual

Read more less

100-Watt Component Speakers Six-1/2" Drivers The CS Series 6-1/2-inch component speakers by Kicker are designed for easy installation in nearly any vehicle. These components include separate titanium flush, angled or surface-mount tweeters and two-way crossovers with tweeter level control to let you customize your sound for the best sonic quality. The Kicker CS Series 6-1/2" speakers work best with up to 100-watts of recommended power. Specifications Woofer Size | in [mm] 6 1/2 [160] Tweeter Size | in [mm] 3/4 [20] Dome Material Titanium Peak Power | [watts] 300 Continuous Power | [watts RMS] 100 Effective Frequency Range | Hz 35-21k Woofer Mounting Hole Diameter | in [mm] 4 13/16 [123] Woofer Bottom Mount Depth | in [mm] 1 11/16 [43] Flush Mounting Tweeter Hole Diameter | in [mm] 1 9/16 [40] Flush Mount Tweeter Depth | in [mm] 9/16 [14.5] High Pass | dB, at Frequency | Hz 12, 4000 Low Pass | dB, at Frequency | Hz 12, 4000 High Frequency Output Attenuation | dB 0, 3, & 6 Bolt-Thru Grilles Yes Kicker CS Component Speaker Manual

Read more less

100-Watt Component Speakers 6.75-Inch Drivers The CS Series 6-3/4-inch component speakers by Kicker are designed for easy installation in nearly any vehicle. These components include separate titanium flush, angled or surface-mount tweeters and two-way crossovers with tweeter level control to let you customize your sound for the best sonic quality. The Kicker CS Series 6-3/4" speakers work best with up to 100-watts of recommended power. Specifications  Woofer Size | in [mm] 6 3/4 [165] Tweeter Size | in [mm] 3/4 [20] Dome Material Titanium Peak Power | [watts] 300 Continuous Power | [watts RMS] 100 Effective Frequency Range | Hz 35-21k Woofer Mounting Hole Diameter | in [mm] 5 1/2 [140] Woofer Bottom Mount Depth | in [mm] 1 13/16 [47] Flush Mounting Tweeter Hole Diameter | in [mm] 1 9/16 [40] Flush Mount Tweeter Depth | in [mm] 9/16 [14.5] High Pass | dB, at Frequency | Hz 12, 4000 Low Pass | dB, at Frequency | Hz 12, 4000 High Frequency Output Attenuation | dB 0, 3, & 6 Bolt-Thru Grilles Yes Kicker CS Component Speaker Manual

Read more less

75-Watt Component Speakers Six-x-Eight" Drivers The CS Series 6-x-8 inch component speakers by Kicker are designed for easy installation in nearly any vehicle. These components include separate titanium flush, angled or surface-mount tweeters and two-way crossovers with tweeter level control to let you customize your sound for the best sonic quality. The Kicker CS Series six-by-eight" speakers work best with up to 75-watts of recommended power. Specifications Woofer Size | in [mm] 6x8 [160x200] Tweeter Size | in [mm] 3/4 [20] Dome Material Titanium Peak Power | [watts] 225 Continuous Power | [watts RMS] 75 Effective Frequency Range | Hz 40-21k Woofer Mounting Hole Diameter | in [mm] 5 x 7 3/16 [126x182] Woofer Bottom Mount Depth | in [mm] 2 3/16 [56] Flush Mounting Tweeter Hole Diameter | in [mm] 1 9/16 [40] Flush Mount Tweeter Depth | in [mm] 9/16 [14.5] High Pass | dB, at Frequency | Hz 12, 4000 Low Pass | dB, at Frequency | Hz 12, 4000 High Frequency Output Attenuation | dB 0, 3, & 6 Bolt-Thru Grilles No Kicker CS Component Speaker Manual

Read more less

150-Watt Component Speakers Six-x-Nine" Drivers The CS Series 6-x-9 inch component speakers by Kicker are designed for easy installation in nearly any vehicle. These components include separate titanium flush, angled or surface-mount tweeters and two-way crossovers with tweeter level control to let you customize your sound for the best sonic quality. The Kicker CS Series six-by-nine" speakers work best with up to 150-watts of recommended power. Specifications  Woofer Size | in [mm] 6x9 [160x230] Tweeter Size | in [mm] 3/4 [20] Dome Material Titanium Peak Power | [watts] 450 Continuous Power | [watts RMS] 150 Effective Frequency Range | Hz 30-21k Woofer Mounting Hole Diameter | in [mm] 5 5/8 x 8 7/16 [143x215] Woofer Bottom Mount Depth | in [mm] 3 3/16 [81] Flush Mounting Tweeter Hole Diameter | in [mm] 1 9/16 [40] Flush Mount Tweeter Depth | in [mm] 9/16 [14.5] High Pass | dB, at Frequency | Hz 12, 4000 Low Pass | dB, at Frequency | Hz 12, 4000 High Frequency Output Attenuation | dB 0, 3, & 6 Bolt-Thru Grilles Yes Kicker CS Component Speaker Manual

Read more less

Alpine 75-Watt 2-Way Component Speaker-System for 2007-2018 Jeep Wrangler-JK These 6.5-inch speakers in the SPV-65X-WRA are tuned specifically for the JK’s in-cabin environment and fit into the factory speaker locations for an easy update that will impress your ears. The SPV-65X-WRA comes with adapters that allow the speakers to be installed as a component set by mounting the tweeters into the tombstones of older JKs or onto the dash for newer JKs. For older JKs that have a sound bar, the adapters convert the speakers into a coaxial design so they can be installed into the sound bar. Driving with the top off is part of the fun of owning a Wrangler, but sometimes you get caught off-guard with the top down and inclement weather. The SPV-65X-WRA is weather resistant and rated IP55, so it’s protected from limited dust ingress and low-pressure water spray from any direction. Specifications 6.5” Component or Coaxial 2-Way Speaker System w/ Convertible Design Weather Resistant (IP55 rating) Power Handling: 75W RMS/225W Peak Nominal Impedance 4Ω Frequency Response: 65-22kHz 1” Teteron Dome Tweeter CustomSteel Frame w/ factory speaker mounting tabs OEM speaker connectors

Read more less

C2-Series 6-Inch 60-Watt Component Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs. The C2-600 system features 6-inch (150 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6-inch (150 mm) format is a direct fit in many Japanese vehicles where a full-size 6.5-inch speaker (165 mm) will not fit without modification. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6-inch (150 mm) speaker. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-600 Manual

Read more less

C2-Series 5.25-Inch 60-Watt Component Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs. The C2-525 system features 5.25-inch (130 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB JL Audio C2-525 Manual

Read more less

C3-Series 6-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The new C3-600 expands the C3 lineup with a direct-fit product for many Japanese vehicles that will not accept a full-size 6.5-inch speaker. The C3-600 system features 6-inch (150 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 89.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 50 Hz - 25 KHz ± 3 dB JL Audio C3-600 Manual

Read more less

C3-Series 5x7" 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. Many people mistakenly believe that an oval speaker cannot perform as well as a round one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C3-570 system features 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are not available for this product. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-570 Manual

Read more less

C3-Series 5.25-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-525 system features 5.25-inch (130 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-525 Manual

Read more less