At this present time our store location is open by appointment only.

Coaxial Speakers

Coaxial Speaker Collection

A coaxial speaker will generally be one speaker that has 2 or more drivers built on to it. These generally come in 2-way and 3-way systems. The amount of different size drivers on a speaker determines how many “way’s” it is. A 3-way coaxial speaker is made of 3 drivers like a 6x9″ woofer, a 2″ mid range and 1″ tweeter. Coaxial speakers are generally made to reproduce the entire audible frequency range except for the lows in one self contained unit. Some coaxial speakers will dip into the low frequency range but are too small to give the thump of a larger driver like a subwoofer.

Subs and speakers are the ultimate end game of your car stereo. Speakers and subs transfer the electrical energy from your amplifier and then reproduce that energy into high and low pressure waves by a moving diaphragm called the cone. The high and low pressure waves are then intercepted by your ear drum and are ultimately perceived by the human ear to be sound. Speakers can make or break the final quality of the sound of your car stereo as well as the acoustics of your vehicle and the location of the speaker to the listening position. Real Time Analyzation, or RTA tuning, and time correction can make a dramatic difference in the final sound quality of your speaker system and should be taken into consideration when updating the speakers in your car stereo.

Subs and speakers come in different sizes, power ratings and shapes to accommodate different installation applications and sometimes specific octave ranges. The speaker cone is also know as a driver. Speaker sizes are usually referred to as driver sizes. As an example, a 6.5″ driver is a round speaker versus a 6×9″ driver is an oval speaker.

RMS vs. MAX power: The RMS rating of any speaker driver is the continuous power rating that the speaker is designed to withstand at a maximum continued volume rating. The RMS rating is the only number to go by when pairing your speakers with an amplifier. As an example a speaker with a 100Watt, or 100W for short, RMS rating and a 300-Watt Max rating is ultimately a 100 Watt speaker. The Max rating is the temporary spikes in voltage that the speaker can handle. A 100-Watt RMS / 300-Watt Max speaker is going to outperform a 100W RMS / 250W Max speaker at higher volumes, but may not be the more detailed reference speaker.

Ohms: The Ohm rating, or resistance rating, of a speaker is an essential part of a well balanced car stereo system. Many JBL factory speaker systems have 2ohm drivers. Most aftermarket speakers are 4ohm drivers. Replacing these types of factory speakers may require a wiring bypass of the factory amplifier.

Driver resistance ratings are essential when pairing subwoofer and speaker drivers with amplifiers. An amplifier that is 750W @ 2ohms might only generally be 500W or less @ 4ohms. When purchasing a subwoofer driver the correct pairing of a subwoofer’s RMS wattage and Ohm ratings with an amplifier’s output power rating is absolutely essential.

Frequency Response: Frequencies are measured in Hertz or Hz for short. The frequency response of speaker drivers will generally fall between 20Hz and 22kHz. At 20Hz the sound spectrum begins. Every time you double your frequency you move up one octave in scale. 20-Hertz to 40-Hertz covers the first Octave, 40Hz to 80Hz covers the next octave and so on. Subwoofer drivers are generally tuned to crossover at 80 Hertz. This can depend on the subwoofer type and the type of music you listen to.

52 products

  • Morel Hybrid Integra 62 : 6.5" Coaxial Door Speakers, 100W RMS

    Morel Hybrid Integra 62 : 6.5" Coaxial Door Speakers, 100W RMS

    Pre-Order Today!

    Hybrid Integra Series 6-1/2" 100-Watt RMS 2-Way Coaxial Door Speakers Embracing Morel’s legendary craftsmanship, engineering, and innovation, the latest Hybrid systems define an ever-evolving concept of high-fidelity speaker design. Now in their fifth generation, the new Hybrid and Hybrid Integra systems give a further refined listening experience, captivating you with the raw emotions of listening to live music. Their subtle balance of resolution, power, and efficiency has been further optimized to exceed expectations regardless of what genre of music you enjoy.   The Integra, Morel’s point source system, is an innovative landmark in speaker design. It utilizes point-source topology to eliminate acoustic problems inherent in conventional coaxial systems. By creating a single sound source on the same axis, the tweeter and woofer seamlessly integrate, generating Omni-directional time alignment, heightened imaging, and sound dispersion. Now the Hybrid is available in 2-way and Integra point source (coaxial) solutions, as well as a new 3-way system to fit nearly any system requirement. CONTROLLED ACOUSTIC RESISTANCEThe C.A.R. Filter™ improves the acoustic loading by controlling airflow within the driver, mimicking the effects of a cabinet while improving power handling by 30%. This provides greater control over the cone movement for improved bass dynamics. EVC MOTORMorel speakers with EVC™ technology utilize voice coils that are up to three times larger than those used in conventional loudspeakers, enabling improved heat dissipation, power handling and linearity. The EVC™ design moves the magnetic motor system to within the voice coil, eliminating stray magnetic flux by effectively directing all the magnetic energy to the voice coil. The EVC architecture is over 90% more efficient than conventional design, magnetically shielded, and highly compact. HEXATECH™ ALUMINIUM VOICE COILMade from 100% aluminum wire shaped like a honeycomb, the Hexatech™ voice coil reduces air gaps in the coil windings, thereby increasing efficiency by up to 20%. Being lightweight, Hexatech™ voice coils are largely responsible for the extraordinary fast transient response Morel drive units are known for. HYBRID MAGNET MOTORThe Hybrid motor drive system uses a ferrite magnet together with a very powerful neodymium magnet. Combined they create a compact, lightweight motor system that is up to four times more powerful than conventional designs of the same size. With Hybrid, more amplified power is converted into sonic energy for flawless performance, even in a small driver. INTEGRADerived from the word “integrate”, Integra is a speaker consisting of both a woofer and tweeter that share a common chassis. Unlike a coaxial, its recessed tweeter is concentrically aligned with the woofer cone. This minimizes phase error and allows the sound field to be constant in all directions, creating a near-perfect time alignment. PAPER CONEIn use since the first loudspeakers, the paper continues to be an exceptional material of choice. Morel’s latest paper composite cones are ultra-lightweight, making them an exceptional pairing for drivers using smaller motors and voice coils. Sold by the Pair Specifications  MODEL SIZE & CONFIGURATION POWER HANDLING (WRMS) / PEAK POWER (W) SENSITIITY (2.83V/1M)(DB) FREQUENCY RESPONSE (HZ) CROSSOVER HYBRID INTEGRA 42 4" 2-way 80 /250 92 80-25000 MXR250.4i HYBRID INTEGRA 52 5¼" 2-way 120 / 500 90 45-25000 MXR250.4i HYBRID INTEGRA 62 6½" 2-way 140 / 600 91 35-25000 MXR250.4i Morel Hybrid Integra Series Door Speaker Manual

    Pre-Order Today!

    $799.99

  • Alpine HDZ-65 : 6.5" Coaxial Door Speakers, 100W RMS Alpine HDZ-65 : 6.5" Coaxial Door Speakers, top side view.

    Alpine HDZ-65 : 6.5" Coaxial Door Speakers, 100W RMS

    Pre-Order Today!

    Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest- quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback. Drawing inspiration from the AlpineF#1Status system, the HDZ-65 features a unified carbon composite cone construction throughout the speaker components for a unified timbre identity. Alpine Proprietary Double Gathered Edge Surround technology gives the speakers ultra-low distortion and linear diaphragm movement that reproduces music true to the artist’s original intentions. Custom developed for Hi-Res Audio Playback, the HDZ-65 has an ultra-wide bandwidth of 55Hz-40kHz which is perfectly suited for accurate reproduction of even the highest quality of studio recordings. Each speaker component is designed to cover a wider range of playback spectrum giving the tuner a wider range of adjustability. The Alpine Status speaker line features two fitments for flexible installation options including a custom-fix model for custom applications and factory-fit models that were intentionally designed to fit into most factory speaker holes without custom work. The HDZ-65 is a factory-fit model that includes a 6.5-inch mid-bass driver and a 1-inch coaxial high-range driver. The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System. Features Hi-Res Audio Playback (192kHz/24Bit) w/full Alpine Status system Carbon Composite Diaphragm Material  Alpine Proprietary Double Gathered Edge Surround  6.5” Mid-Bass Driver (16.5cm) 1” Coaxial Tweeter (2.5cm) Specifications 100W RMS 300W Peak Power Handling  Frequency response: 55Hz – 40kHz Sensitivity: 88dB Sold by the Pair Alpine HDZ-65 Manual

    Pre-Order Today!

    $549.99

  • JL Audio C3-650 : 6.5" Convertible Component Speakers - 75W RMS JL Audio C3-650 : 6.5" Convertible Component Speaker.

    JL Audio C3-650 : 6.5" Convertible Component Speakers, 75W RMS

    Pre-Order Today!

    C3-Series 6.5-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650 system features 6.5-inch (165 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-650 Manual

    Pre-Order Today!

    $549.99

  • JL Audio C3-600 : 6" Convertible Component Speakers - 75W RMS JL Audio C3-600 : 6" Convertible Component Speaker.

    JL Audio C3-600 : 6" Convertible Component Speakers, 75W RMS

    Pre-Order Today!

    C3-Series 6-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The new C3-600 expands the C3 lineup with a direct-fit product for many Japanese vehicles that will not accept a full-size 6.5-inch speaker. The C3-600 system features 6-inch (150 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 89.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 50 Hz - 25 KHz ± 3 dB JL Audio C3-600 Manual

    Pre-Order Today!

    $549.99

  • JL Audio C3-570 : 5x7" Convertible Component Speakers - 75W RMS JL Audio C3-570 : 5x7" Convertible Component Speakers.

    JL Audio C3-570 : 5x7" Convertible Component Speakers, 75W RMS

    Pre-Order Today!

    C3-Series 5x7" 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. Many people mistakenly believe that an oval speaker cannot perform as well as a round one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C3-570 system features 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are not available for this product. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-570 Manual

    Pre-Order Today!

    $549.99

  • JL Audio C3-525 : 5.25" Convertible Component Speakers - 75W RMS JL Audio C3-525 : 5.25" Convertible Component Speakers.

    JL Audio C3-525 : 5.25" Convertible Component Speakers, 75W RMS

    Pre-Order Today!

    C3-Series 5.25-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-525 system features 5.25-inch (130 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-525 Manual

    Pre-Order Today!

    $549.99

  • 100W 6.75" Coaxial Speakers : Kicker 44QSC674 100W 6.75" Coaxial Speakers : Kicker 44QSC674 driver shown.

    Kicker 44QSC674 : 100W 6.75" Coaxial Speakers

    Pre-Order Today!

    6-3/4" 100-Watt Coaxial Speakers This pair of QS series 6.75" coaxial audiophile speaker drivers by Kicker feature neodymium magnets on the woofer and tweeter, and are bi-amp capable. Incased within the speaker chassis is you will find a 25mm Teteron® dome tweeter with Kicker's custom wave guide technology for near perfect phase alignment for smooth frequency response. The injection-molded Polypropylene cone of this coaxial door speaker is impregnated with carbon-fiber for tight, accurate midrange. An NBR rubber surround provides superior damping, and complemented by a signature blue double surround stitching. The independent 18dB crossover has been optimized for size, and features built-in tweeter protection. Utilizing Metallized Polypropylene capacitors, high-powered resistors and audiophile-grade air-core inductors, the crossover delivers outstanding overall sound quality and easy mounting in a door or under a seat. These Kicker QS 6-and-3/4 inch door speakers have an amplified RMS power range of 100W. This pair of drivers also has speaker adaptor rings, allowing them to be installed using select factory location mounting. Specifications Woofer (in., mm) 6 ¾, 165 Tweeter (in., mm) 1, 25 Tweeter dome material Teteron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 100 Peak Power (watts, per ANSI/CTA-2031-A) 200 Sensitivity [1W, 1m] 86dB Frequency Response [Hz] 40-20k Woofer Mounting Hole Diameter [in, mm] 5 9/16, 141 Woofer Mounting Depth [in, mm] 2 9/16, 64.9 High Pass [dB], at Frequency [Hz] 18, 5.5k Low Pass [dB], at Frequency [Hz] 18, 5.5k Comments Crossover is bi-amp capable. Kicker QS Series Coaxial Speaker Manual

    Pre-Order Today!

    $449.99

  • 100W 6x9" Coaxial Speakers : Kicker 44QSC694 100W 6x9" Coaxial Speakers : Kicker 44QSC694 driver shown.

    Kicker 44QSC694 : 100W 6x9" Coaxial Speakers

    Pre-Order Today!

    6x9-Inch 100-Watt Coaxial Speakers This pair of QS series 6x9" coaxial audiophile speaker drivers by Kicker feature neodymium magnets on the woofer and tweeter, and are bi-amp capable. Incased within the speaker chassis is you will find a 25mm Teteron® dome tweeter with Kicker's custom wave guide technology for near perfect phase alignment for smooth frequency response. The injection-molded Polypropylene cone of this coaxial door speaker is impregnated with carbon-fiber for tight, accurate midrange. An NBR rubber surround provides superior damping, and complemented by a signature blue double surround stitching. The independent 18dB crossover has been optimized for size, and features built-in tweeter protection. Utilizing Metallized Polypropylene capacitors, high-powered resistors and audiophile-grade air-core inductors, the crossover delivers outstanding overall sound quality and easy mounting in a door or under a seat. These Kicker QS 6x9 inch door speakers have an amplified RMS power range of 100W. This pair of drivers also has speaker adaptor rings, allowing them to be installed using select factory location mounting. Specifications Woofer (in., mm) 6x9, 160x230 Tweeter (in., mm) 1, 25 Tweeter dome material Teteron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 100 Peak Power (watts, per ANSI/CTA-2031-A) 200 Sensitivity [1W, 1m] 88dB Frequency Response [Hz] 30-20k Woofer Mounting Hole Diameter [in, mm] 4-13/16x8-5/8, 121.9x219 Woofer Mounting Depth [in, mm] 3, 76.2 High Pass [dB], at Frequency [Hz] 18, 5.5k Low Pass [dB], at Frequency [Hz] 18, 5.5k Comments Crossover is bi-amp capable. Kicker QS Series Coaxial Speaker Manual

    Pre-Order Today!

    $449.99

  • Alpine R2-S69 : 6x9" Coaxial Door Speaker System, 100W RMS Alpine R2-S69 : 6x9" Coaxial Door Speaker System, woofer.

    Alpine R2-S69 : 6x9" Coaxial Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S69 is a standard coaxial speaker set that includes a 6x9” Mid-Range and 1” Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Die-Cast Aluminum Basket  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Full Passive Performance Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6x9” Mid-Bass with 1” Tweeter  Frequency Response: 60Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $299.99

  • JL Audio C2-690tx : 6x9" 3-Way Coaxial Speakers - 70W RMS JL Audio C2-690tx : 6x9" 3-Way Coaxial Speaker top side with no grille.

    JL Audio C2-690tx : 6x9" 3-Way Coaxial Speakers, 70W RMS

    2 Available for pickup

    C2-Series 6x9" 70-Watt  3-Way Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-690tx system features 6 x 9-inch (150 x 230 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6 x 9-inch (150 x 230 mm) format is a direct fit in many vehicles. The Mid-Range driver is ferrofluid-cooled, with a 2-inch Mylar® cone diaphragm to smoothly bridge the gap between the woofer and the dome tweeter. Tweeters are mounted next to the mid-range driver and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specs Continuous Power Handling (RMS) 70 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 125 W / Ch. System Efficiency 93 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB JL Audio C2-690tx Manual

    2 Available for pickup

    $259.99

  • Alpine R2-S65 : 6.5" Coaxial Door Speaker System, 100W RMS Alpine R2-S65 : 6.5" Coaxial Door Speaker System, woofer.

    Alpine R2-S65 : 6.5" Coaxial Door Speaker System, 100W RMS

    Pre-Order Today!

    Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status systems, the Next-Generation R-Series Speakers are Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy. The new lightweight and rigid glass fiber-reinforced cone material allows for extreme movement and low distortion which results in an incredibly accurate and clean sound during playback. The Next-Generation R-Series speakers utilize a ferrite magnet, different from the neodymium from previous generations, and a larger motor structure that contributes to more mid-bass during the playback. Despite the larger motor structure, the speakers still maintain the same depth for easy installation. Continuing with the Next-Generation R-Series speaker line is Alpine-exclusive High Amplitude Multi-Roll (HAMR) surround technology that increased excursions while maintaining linearity for more accurate music reproduction. The Next-Generation R-Series speaker line offers two pathways for performance: the “Pro” and “Standard” models. The R2-S65 is a standard coaxial speaker set that includes a 6.5” Mid-Range and 1” Coaxial Tweeter with a flexible in-line crossover network that simplifies installation. Sold as a pair. Features Hi-Res Audio Certified Glass Fiber Reinforced Cone  Ferrite Magnet Structure  High-Amplitude Multi-Roll (H.A.M.R.) Surround  2 Premium-Grade Crossover Networks   Magnesium Hard-Dome Tweeters with Swivel Mount Design and Threaded Removable Housing  Protective Open Mesh Grille Pair Included Specifications 6.5” Mid-Bass with 1” Tweeter Frequency Response: 65Hz -40kHz  Power Handling: 100W RMS / 300W Peak

    Pre-Order Today!

    $249.99

  • JL Audio C2-650x : 6.5" Coaxial Speakers - 60W RMS JL Audio C2-650x : 6.5" Coaxial Speaker front side.

    JL Audio C2-650x : 6.5" Coaxial Speakers, 60W RMS

    4 Available for pickup

    C2-Series 6.5-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-650x system features 6.5-inch (165 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-650x Manual

    4 Available for pickup

    $249.99

  • JL Audio C2-600x : 6" Coaxial Speakers - 60W RMS JL Audio C2-600x : 6" Coaxial Speaker grilles.

    JL Audio C2-600x : 6" Coaxial Speakers, 60W RMS

    2 Available for pickup

    C2-Series 6-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-600x system features 6-inch (150 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6-inch (150 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB JL Audio C2-600x Manual

    2 Available for pickup

    $249.99

  • JL Audio C2-570x : 5x7" Coaxial Speakers - 60W RMS

    JL Audio C2-570x : 5x7" Coaxial Speakers, 60W RMS

    6 Available for pickup

    C2-Series 5x7-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. Many people mistakenly believe that an oval speaker cannot perform as well as a round one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to JL's 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C2-570x system features 5 x 7 / 6 x 8-inch (125 x 180 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Grilles are not available for this speaker system. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB JL Audio C2-570x Manual

    6 Available for pickup

    $249.99

  • JL Audio C2-525x : 5.25" Coaxial Speakers - 60W RMS JL Audio C2-525x : 5.25" Coaxial Speaker grilles.

    JL Audio C2-525x : 5.25" Coaxial Speakers, 60W RMS

    2 Available for pickup

    C2-Series 5.25-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-525x system features 5.25-inch (130 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB JL Audio C2-525x Manual

    2 Available for pickup

    $249.99

  • 90W 6x9" Motorcycle Coaxial Speakers, 2Ω or 4Ω Voice Coil : Kicker 40PS69 90W 6x9" Motorcycle Coaxial Speakers, 2Ω or 4Ω Voice Coil : Kicker 40PS69, with grille.

    Kicker 40PS69 : 90W 6x9" Motorcycle Coaxial Speakers, 2Ω or 4Ω Voice Coil

    Pre-Order Today!

    6 x 9-Inch 90-Watt RMS Coaxial Motorcycle Speakers, 2-Ohm or 4-Ohm Drivers The 6x9" P40PS motorcycle coaxial speakers by Kicker are designed by bike riders and power-sports enthusiasts to sound good and last while retaining a weatherproof rating. These 90W Kicker speakers are the perfect solution for motorcycles, ATV’s and Side-by-Sides. The Kicker PS 6x9" Coaxial Speaker Includes One Pair Of 6x9" Speakers 2 or 4 Ohm Voice Coil Recommended Power 90 Watts - Peak 180 Watts High-Efficiency Titanium Tweeter Perfect Fairing Drop-Ins  The Kicker 40PS692 and 40PS694 weather-proof drivers are a perfect fairing drop-in on many motorcycles. Use these 6x9-inch speakers with UTV, ATV, marine, or outdoor systems. The rugged PS69 system utilizes heavy-duty ceramic magnets for high power handling and volume for ultra-clear music reproduction through helmets - even at highway speeds. Specifications  Woofer (in, mm) 6 x 9, 150 x 230 Tweeters (in, mm) 1, 25 Impedance (Ohms) 2 Max Rec Amp Power (watts PEAK/RMS) 180/90 Sensitivity (dB 1w/1m) 87.3 Frequency Response (Hz) 40 - 20k Mounting Hole Diameter (in, mm) 5/8 x 8-7/16, 143 x 214 Mounting Depth (in, mm) 3 1/4, 83 Weight (oz, g) 43.5, 1233 Grilles Yes Kicker 40PS69 Manual

    Pre-Order Today!

    $219.99

  • Alpine SPV-65X-WRA : 6.5" 75W Speaker System for Wrangler JK 2007-2018

    Alpine SPV-65X-WRA : 6.5" 75W Speaker System, 2007-2018 Wrangler JK

    Pre-Order Today!

    Alpine 75-Watt 2-Way Component Speaker-System for 2007-2018 Jeep Wrangler-JK These 6.5-inch speakers in the SPV-65X-WRA are tuned specifically for the JK’s in-cabin environment and fit into the factory speaker locations for an easy update that will impress your ears. The SPV-65X-WRA comes with adapters that allow the speakers to be installed as a component set by mounting the tweeters into the tombstones of older JKs or onto the dash for newer JKs. For older JKs that have a sound bar, the adapters convert the speakers into a coaxial design so they can be installed into the sound bar. Driving with the top off is part of the fun of owning a Wrangler, but sometimes you get caught off-guard with the top down and inclement weather. The SPV-65X-WRA is weather resistant and rated IP55, so it’s protected from limited dust ingress and low-pressure water spray from any direction. Specifications 6.5” Component or Coaxial 2-Way Speaker System w/ Convertible Design Weather Resistant (IP55 rating) Power Handling: 75W RMS/225W Peak Nominal Impedance 4Ω Frequency Response: 65-22kHz 1” Teteron Dome Tweeter CustomSteel Frame w/ factory speaker mounting tabs OEM speaker connectors

    Pre-Order Today!

    $219.99

  • JL Audio C1-690tx : 6x9" Coaxial Speakers - 60W RMS 3-Way JL Audio C1-690tx : 6x9" Coaxial Speakers - 60W RMS 3-Way, front side.

    JL Audio C1-690tx : 6x9" Coaxial Speakers, 60W RMS 3-Way

    Pre-Order Today!

    C1-Series 6x9-Inch 60-Watt Coaxial Speaker System, 3-Way C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with dual true, edge-driven, aluminum dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension. Both high-frequency drivers also benefit from the damping of silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 36 Hz - 24 KHz ± 3 dB JL Audio C1-690tx Manual

    Pre-Order Today!

    $179.99

  • JL Audio C2-400x : 4" Coaxial Speakers - 35W RMS JL Audio C2-400x : 4" Coaxial Speaker grilles.

    JL Audio C2-400x : 4" Coaxial Speakers, 35W RMS

    Pre-Order Today!

    C2-Series 4-Inch 35-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-400x system features 4-inch (100 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Breakaway mounting tabs on the woofer frame allow the C2-400x to be installed in four-hole or two-hole configurations. Injection-Molded adaptor plates are also included to allow mounting of the C2-400x speakers into a 4 x 6 (100 x 150 mm) speaker location. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 35 W Peak Music Power 105 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 84.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 71 Hz - 22 KHz ± 3 dB JL Audio C2-400x Manual

    Pre-Order Today!

    $179.99

  • Kicker 10PS5250 : 50W 5.25" Motorcycle Coaxial Speakers, 2Ω or 4Ω Kicker 10PS52502 : 5.25-Inch 50-Watt Coaxial Motorcycle Speakers, 2-Ohm, side view.Kicker 10PS5250 : 50W 5.25" Motorcycle Coaxial Speakers, 2Ω or 4Ω, side view.

    Kicker 10PS5250 : 50W 5.25" Motorcycle Coaxial Speakers, 2Ω or 4Ω

    Pre-Order Today!

    5.25-Inch 50-Watt Coaxial Motorcycle Speakers, 2-Ohm or 4-Ohm Voice Coil Kicker 10PS5250 speakers are designed by bike riders and power-sports enthusiasts to sound good and last through every kind of weather. The Kicker PS 5.25 Inch 2Ω Motorcycle Coaxial Speaker is built to sound great on the road or the trail.These 5 1/4" Motorcycle speakers are weatherproof with a lightweight design featuring titanium tweeters and neodymium magnets. These Kicker 50 watt speakers deliver clean and crisp sound even through road, wind and motor noise. Add a Kicker PXA weatherproof amplifier and you will be ready for the road or the trail.These Kicker 10PS5250 speakers work best with 50 watts of recommended power.  Specifications     Woofer 5 1/4", 133mm Tweeters 3/4", 20mm Impedance 2Ω or 4Ω Max Rec Amp Power (watts PEAK/RMS) 100W/50W Sensitivity 88.3dB @ 1w/1m Frequency Response 60Hz - 20kHz Mounting Hole Diameter 4 7/8", 124mm Mounting Depth 2 3/16", 56mm Weight 12.6oz, 358g Grilles Yes (H-D Bat-wing) Kicker 10PS5250 Manual

    Pre-Order Today!

    $169.99

  • JL Audio C1-690x  : 6x9" Coaxial Speakers - 60W RMS JL Audio C1-690x  : 6x9" Coaxial Speakers - 60W RMS, front side.

    JL Audio C1-690x : 6x9" Coaxial Speakers, 60W RMS

    Pre-Order Today!

    C1-Series 6x9-Inch 60-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 91.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB JL Audio C1-690x Manual

    Pre-Order Today!

    $169.99

  • Kicker 47KSC6904 : Six-by-Nine-Inch Coaxial Speaker Drivers, 150-Watt RMS. Kicker 47KSC6904 : Six-by-Nine-Inch Coaxial Speaker Drivers, 150-Watt RMS, side view.

    Kicker 47KSC6904 : 6x9" 150W Coaxial Speakers

    Pre-Order Today!

    Six-by-Nine-Inch Coaxial Speaker Drivers, 150-Watt RMS The Kicker KS series 6x9-inch coaxial speakers come with custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 150 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6 x 9, 160 x 230 Tweeter [in, mm] 1, 25 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-150 Sensitivity [1W, 1m] 92 Frequency Response [Hz] 30-21k Mounting Hole Diameter [in, mm] 5-11/16 x 8-7/16, 144 x 215 Top Mount Depth [in, mm] 3-3/16, 81 Bottom Mount Depth [in,mm] 3-11/16, 93 Tweeter Protrusion [in,mm] 1/16, 1 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    Pre-Order Today!

    $159.99

  • JL Audio C1-570x : 5x7" Coaxial Speakers - 50W RMS JL Audio C1-570x : 5x7" Coaxial Speakers - 50W RMS, front side.

    JL Audio C1-570x : 5x7" Coaxial Speakers, 50W RMS

    Pre-Order Today!

    C1-Series 5x7-Inch 50-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included, allowing the C1-570x to be installed in bottom-mount applications. The speaker baskets are also equipped with slotted mounting holes to fit into 6 x 8-inch factory speaker locations. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-570x is a proprietary, stamped, steel 5 x 7-inch (125 x 180 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 40 Hz - 24 KHz ± 3 dB JL Audio C1-570x Manual

    Pre-Order Today!

    $159.99

  • Kicker 40PS4 : 4-Inch 50-Watt RMS Coaxial Motorcycle Speakers, 2-Ohm or 4-Drivers 50W 4" Motorcycle Coaxial Speakers, 2Ω or 4Ω Drivers : Kicker 40PS4

    Kicker 40PS4 : 50W 4" Motorcycle Coaxial Speakers, 2Ω or 4Ω Drivers

    Pre-Order Today!

    4-Inch 50-Watt RMS Coaxial Motorcycle Speakers, 2-Ohm or 4-Drivers The 40PS4 motorcycle speakers by Kicker are designed by bike riders and powersports enthusiasts, to sound good while remaining lightweight and weatherproof. These drivers are the perfect solution for motorcycles, ATV’s and Side by Sides. The 40PS42 and 40PS44 are weatherproof speakers and are made to deliver clean, crisp music, on the road and off – even through a helmet. Kicker construction that stands up to the elements is combined with high-grade sound quality, without modifying your motorcycle speaker fairing or adding unwanted weight to your power sport machine. Add a Kicker PXA amplifier to your bike to complement the rough roads, and rougher trails.These PSM speakers work best with 50 watts of recommended power.  Specifications  Woofer (in, mm) 4, 100 Tweeters (in, mm) 3/4, 20 Impedance (Ohms) 2 Max Rec Amp Power (watts PEAK/RMS) 100/50 Sensitivity (dB 1w/1m) 85.8 Frequency Response (Hz) 100 - 20k Mounting Hole Diameter (in, mm) 3 5/8, 93 Mounting Depth (in, mm) 1 11/16, 43 Weight (oz, g) 11.9, 338 Grilles Yes Kicker 40PS4 Manual

    Pre-Order Today!

    $149.99

  • JL Audio C2-350x : 3.5" Coaxial Speakers - 25W RMS

    JL Audio C2-350x : 3.5" Coaxial Speakers, 25W RMS

    Pre-Order Today!

    C2-Series 3.5-Inch 25-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-350x system features 3.5-inch (90 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are not available for this speaker system. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 25 W Peak Music Power 75 W Recommended Amplifier Power (RMS) 10 - 40 W / Ch. System Efficiency 83 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 130 Hz - 22 KHz ± 3 dB JL Audio C2-350x Manual

    Pre-Order Today!

    $149.99

  • Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers, front side.

    Alpine S2-S65 : 6.5" 80W RMS Coaxial Speakers

    3 Available for pickup

    Alpine 6-1/2-Inch Coaxial 2-Way Speakers, 80-Watt RMS Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry-level price point.  Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. Alpine-exclusive High Amplitude Multi- Roll (HAMR) surround technology is integrated into the speaker design which allows for maximum cone movement, delivering powerful and accurate bass notes. The S-Series S2-S65 is compatible with the KTE-S65G Speaker Grille (sold separately). This sleek and stylish grille will not only add a visual upgrade to your speakers but also provide protection against any damage. Specifications Hi-Res Audio Certified (Up to 40kHz) Poly Propylene, Glass Fiber, and Mica Cone Material Lightweight Design with High Output and Low Distortion High-Amplitude Multi-Roll (H.A.M.R.) Surround   Integrated 1” Tweeters (Coaxial) Compatible with KTE-S65G Speaker Grille (sold separately) Woofer Size: 6.5”  Tweeter Size: 1” (Coaxial) Power Handling: 80W RMS / 240W Peak Frequency Response: 70Hz - 40kHz (Hi-Res) Sensitivity: 88dB

    3 Available for pickup

    $129.99

  • Sale -$60.00 Kicker 47KSC69304 : Six-by-Nine-Inch 3-Way Coaxial Speaker Drivers, 150-Watt RMS Kicker 47KSC69304 : Six-by-Nine-Inch 3-Way Coaxial Speaker Drivers, 150-Watt RMS, top side view.

    Kicker 47KSC69304 : 6x9" 150W 3-Way Coaxial Speakers - Discontinued

    2 Available for pickup

    Six-by-Nine-Inch 3-Way Coaxial Speaker Drivers, 150-Watt RMS The Kicker KS series 6x9-inch 3-way coaxial speakers come with custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 150 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6 x 9, 160 x 230 Midrange [in, mm] 1, 25 Tweeter [in, mm] 3/4, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-150 Sensitivity [1W, 1m] 92 Frequency Response [Hz] 30-21k Mounting Hole Diameter [in, mm] 5-11/16 x 8-7/16, 144 x 215 Top Mount Depth [in, mm] 3-1/8, 80 Bottom Mount Depth [in,mm] 3-5/8, 92 Tweeter Protrusion [in,mm] 3/16, 5 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    2 Available for pickup

    $189.99$129.99

  • Kicker 47KSC6804 : Six-by-Eight-Inch Coaxial Speaker Drivers, 75-Watt RMS, top side. Kicker 47KSC6804 : Six-by-Eight-Inch Coaxial Speaker Drivers, 75-Watt RMS

    Kicker 47KSC6804 : 6x8" 75W Coaxial Speakers

    3 Available for pickup

    Six-by-Eight-Inch Coaxial Speaker Drivers, 75-Watt RMS The Kicker KS series six-by-8-inch coaxial speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6 x 8, 160 x 200 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 45-21k Mounting Hole Diameter [in, mm] 5 x 7-3/16, 127 x 182 Top Mount Depth [in, mm] 2-1/4, 58 Bottom Mount Depth [in,mm] 2-5/8, 67 Tweeter Protrusion [in,mm] 1/16, 2 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    3 Available for pickup

    $129.99

  • Kicker 47KSC6704 : 6-3/4-Inch Coaxial Speaker Drivers, 100-Watt RMS Kicker 47KSC6704 : 6-3/4-Inch Coaxial Speaker Drivers, 100-Watt RMS, side view.

    Kicker 47KSC6704 : 100W 6.75" Coaxial Speakers

    Pre-Order Today!

    6.75-Inch Coaxial Speaker Drivers, 100-Watt RMS The Kicker KS series six-and-three-quarter-inch coaxial speakers come with three custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 100 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6-3/4, 165 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-100 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 40-21k Mounting Hole Diameter [in, mm] 5-9/16, 141 Top Mount Depth [in, mm] 1-13/16, 46 Bottom Mount Depth [in,mm] 2, 50 Tweeter Protrusion [in,mm] 3/8, 10 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    Pre-Order Today!

    $129.99

  • Kicker 47KSC6504 : 6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS, top side. Kicker 47KSC6504 : 6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS, shown with grille.

    Kicker 47KSC6504 : 100W 6.5" Coaxial Speakers

    3 Available for pickup

    6-1/2-Inch Coaxial Speaker Drivers, 100-Watt RMS The Kicker KS series six-and-a-half-inch coaxial speakers come with three custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 100 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6-1/2, 160 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-100 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 43-21k Mounting Hole Diameter [in, mm] 4-13/16, 123 Top Mount Depth [in, mm] 1-13/16, 46 Bottom Mount Depth [in,mm] 2-3/16, 54 Tweeter Protrusion [in,mm] 5/16, 8 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    3 Available for pickup

    $129.99

  • Kicker 47KSC504 : 5-1/4-Inch Coaxial Speaker Drivers, 75-Watt RMS. Kicker 47KSC504 : 5-1/4-Inch Coaxial Speaker Drivers, 75-Watt RMS, front side view.

    Kicker 47KSC504 : 75W 5.25" Coaxial Speakers

    2 Available for pickup

    5-1/4-Inch Coaxial Speaker Drivers, 75-Watt RMS The Kicker KS series five-and-a-quarter-inch coaxial speakers come with three custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 5-1/4, 130 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 45-21k Mounting Hole Diameter [in, mm] 4-1/2, 115 Top Mount Depth [in, mm] 1-3/4, 45 Bottom Mount Depth [in,mm] 2, 52 Tweeter Protrusion [in,mm] 1/4, 6 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    2 Available for pickup

    $129.99

  • 4x10" 75W Coaxial Speakers : Kicker 47KSC41004 front side. 4x10" 75W Coaxial Speakers : Kicker 47KSC41004

    Kicker 47KSC41004 : 75W 4x10" Coaxial Speakers

    Pre-Order Today!

    Four-by-Ten-Inch Coaxial Speaker Drivers, 75-Watt RMS KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Specifications Speaker Design 2-Way Woofer [in, mm] 4x10, 100x250 Tweeter [in, mm] ½, 13 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 45-20k Mounting Hole Diameter [in, mm] 3-7/8 x 9-3/8, 99 x 238 Top Mount Depth [in, mm] 2-3/8, 61 Bottom Mount Depth [in,mm] 2-13/16, 71 Tweeter Protrusion [in,mm] 0 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    Pre-Order Today!

    $129.99

  • 6x9" 3-Way Coaxial Speakers, 150W : Kicker 46CSC6934 6x9" 3-Way Coaxial Speakers, 150W : Kicker 46CSC6934 shown with no grille.

    Kicker 46CSC6934 : 6x9" 3-Way Coaxial Speakers, 150W

    Pre-Order Today!

    150-Watt 6x9-Inch Coaxial Speakers, 4-Ohm These CS series 6x9" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 150W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. These Kicker CS series 6 by 9" speakers work best with 150 watts of recommended power. Specifications Speaker Design 3 - way Woofer Size | in [mm] 6x9 [160x230] Mid Size | in [mm] 2 [50] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.5 Peak Power | Watts 450 Continuous Power | Watts, RMS 150 Sensitivity [SPLo] | dB @ 1W, 1m 92 Effective Frequency Range | Hz 30-20k Mounting Hole Diameter | in [mm] 5 5/8 x 8 7/16 [143x215] Top Mount Depth | in [mm] 7/16 [12] Bottom Mount Depth | in [mm] 3 3/16 [81] Tweeter Protrusion | in [mm] 1/16 [1] Grilles Yes Tweeter Magnet Material Electric Crystal Motor Tweeter Dome Material PEI [polyether imide] Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam Kicker CS Series Coaxial Speaker Manual

    Pre-Order Today!

    $129.99

  • Alpine S-S57 : 5x7" 75W RMS Coaxial Speakers

    Alpine S-S57 : 5x7" 75W RMS Coaxial Speakers

    Pre-Order Today!

    Alpine 5X7-Inch Coaxial 2-Way Speakers, 75-Watt RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specifications 75W RMS/230W Peak Nominal Impedance 4Ω Frequency Response: 73-22kHz 1” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround CustomStamped Steel Frame 30mm voice coil

    Pre-Order Today!

    $129.99

  • JL Audio C1-650x : 6.5" Coaxial Speakers - 50W RMS JL Audio C1-650x : 6.5" Coaxial Speakers - 50W RMS, front side.

    JL Audio C1-650x : 6.5" Coaxial Speakers, 50W RMS

    Pre-Order Today!

    C1-Series 6.5-Inch 50-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many "6-inch" speaker locations as well. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 24 KHz ± 3 dB JL Audio C1-650x Manual

    Pre-Order Today!

    $129.99

  • Alpine S-S65 : 6.5" 80W RMS Coaxial Speakers

    Alpine S-S65 : 6.5" 80W RMS Coaxial Speakers

    Pre-Order Today!

    Alpine 6-1/2-Inch Coaxial 2-Way Speakers, 80-Watt RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specifications 80W RMS/240W Peak Nominal Impedance 4Ω Frequency Response: 70-22kHz 1” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround CustomStamped Steel Frame 35mm voice coil Optional grille sold separately (KTE-S65G)

    Pre-Order Today!

    $119.99

  • JL Audio C1-525x : 5.25" Coaxial Speakers - 50W RMS JL Audio C1-525x : 5.25" Coaxial Speakers - 50W RMS, front side.

    JL Audio C1-525x : 5.25" Coaxial Speakers - 50W RMS

    4 Available for pickup

    C1-Series 5.25-Inch 50-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 54 Hz - 24 KHz ± 3 dB JL Audio C1-525x Manual

    4 Available for pickup

    $119.99

  • 4x6" 75W Coaxial Speakers : Kicker 47KSC4604 4x6" 75W Coaxial Speakers : Kicker 47KSC4604 front side view.

    Kicker 47KSC4604 : 75W 4x6" Coaxial Speakers

    2 Available for pickup

    Four-by-Six-Inch Coaxial Speaker Drivers, 75-Watt RMS The Kicker KS series 4x6-inch coaxial speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Specifications Speaker Design 2-Way Woofer [in, mm] 4x6, 100x160 Tweeter [in, mm] ½, 13 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 50-20k Mounting Hole Diameter [in, mm] 4x5-5⁄16, 101x151 Top Mount Depth [in, mm] 1-11⁄16, 44 Bottom Mount Depth [in,mm] 2, 51 Tweeter Protrusion [in,mm] 1/16, 2 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    2 Available for pickup

    $99.99

  • Kicker 47KSC404 : Four-Inch Coaxial Midrange-Tweeter Drivers, 75-Watt RMS 4" 75W Coaxial Speakers : Kicker 47KSC404 front side.

    Kicker 47KSC404 : 4" 75W Coaxial Speakers

    3 Available for pickup

    Four-Inch Coaxial Midrange-Tweeter Drivers, 75-Watt RMS The Kicker KS series four-inch coaxial speakers come with a custom bracket option built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 4, 100 Tweeter [in, mm] ½, 13 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 60-20k Mounting Hole Diameter [in, mm] 3-11⁄16, 94 Top Mount Depth [in, mm] 1-13⁄16, 46 Bottom Mount Depth [in,mm] 2-1⁄16, 51 Tweeter Protrusion [in,mm] 1/8, 3 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    3 Available for pickup

    $99.99

  • Alpine S-S50 : 5.25" 55W RMS Coaxial Speakers

    Alpine S-S50 : 5.25" 55W RMS Coaxial Speakers

    Pre-Order Today!

    Alpine 5-1/4" Coaxial 2-Way Speakers, 55-Watts RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specifications 55W RMS/170W Peak Nominal Impedance 4Ω Frequency Response: 80-22kHz 1” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround CustomStamped Steel Frame 25mm voice coil Optional grille sold separately (KTE-S50G)

    Pre-Order Today!

    $99.99

  • JL Audio C1-400x : 4" Coaxial Speakers - 35W RMS JL Audio C1-400x : 4" Coaxial Speakers - 35W RMS, front side.

    JL Audio C1-400x : 4" Coaxial Speakers, 35W RMS

    Pre-Order Today!

    C1-Series 4-Inch 35-Watt Coaxial Speaker System C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 35 W Peak Music Power 105 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 84.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 64 Hz - 24 KHz ± 3 dB JL Audio C1-400x Manual

    Pre-Order Today!

    $99.99

  • 6x8" Coaxial Speakers, 75W : Kicker 46CSC684 6x8" Coaxial Speakers, 75W : Kicker 46CSC684 front side view.

    Kicker 46CSC684 : 6x8" Coaxial Speakers, 75W

    Pre-Order Today!

    75-Watt 6x8-Inch Coaxial Speakers, 4-Ohm These CS series 6x8" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 75W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. These Kicker CS series 6 by 8" speakers work best with 75 watts of recommended power. Specifications Speaker Design 2 - way Woofer Size | in [mm] 6x8 [160x200] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.5 Peak Power | Watts 225 Continuous Power | Watts, RMS 75 Sensitivity [SPLo] | dB @ 1W, 1m 90 Effective Frequency Range | Hz 45-20k Mounting Hole Diameter | in [mm] 5 x 7 3/16 [126x182] Top Mount Depth | in [mm] 3/8 [9] Bottom Mount Depth | in [mm] 2 3/16 [56] Tweeter Protrusion | in [mm] 0 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material PEI [polyether imide] Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam Kicker CS Series Coaxial Speaker Manual

    Pre-Order Today!

    $89.99

  • 6.75" Coaxial Speakers, 100W : Kicker 46CSC674 6.75" Coaxial Speakers, 100W : Kicker 46CSC674 shown with no grille.

    Kicker 46CSC674 : 100W 6.75" Coaxial Speakers

    Pre-Order Today!

    100-Watt 6.75-Inch Coaxial Speakers, 4-Ohm These CS series 6.75" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 100W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. The Kicker CS series 6 and a 3/4" speakers work best with 100 watts of recommended power. Specifications Speaker Design 2 - way Woofer Size | in [mm] 6 3/4 [165] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.3 Peak Power | Watts 300 Continuous Power | Watts, RMS 100 Sensitivity [SPLo] | dB @ 1W, 1m 90 Effective Frequency Range | Hz 40-20k Mounting Hole Diameter | in [mm] 5 1/2 [140] Top Mount Depth | in [mm] 3/16 [4] Bottom Mount Depth | in [mm] 1 13/16 [47] Tweeter Protrusion | in [mm] 0 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material PEI [polyether imide] Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam

    Pre-Order Today!

    $89.99

  • 6.5" Coaxial Speakers, 100W : Kicker 46CSC654 6.5" Coaxial Speakers, 100W : Kicker 46CSC654 shown without grille.

    Kicker 46CSC654 : 100W 6.5" Coaxial Speakers

    3 Available for pickup

    100-Watt 6.5-Inch Coaxial Speakers, 4-Ohm These CS series 6.5" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 100W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. These Kicker CS series 6 and a 1/2" speakers work best with 100 watts of recommended power. Specifications Speaker Design 2 - way Woofer Size | in [mm] 6 1/2 [160] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.3 Peak Power | Watts 300 Continuous Power | Watts, RMS 100 Sensitivity [SPLo] | dB @ 1W, 1m 90 Effective Frequency Range | Hz 40-20k Mounting Hole Diameter | in [mm] 4 13/16 [123] Top Mount Depth | in [mm] 3/8 [9] Bottom Mount Depth | in [mm] 1 11/16 [43] Tweeter Protrusion | in [mm] 0 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material PEI [polyether imide] Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam Kicker CS Series Coaxial Speaker Manual

    3 Available for pickup

    $89.99

  • 5.25" Coaxial Speakers, 75W : Kicker 46CSC54 5.25" Coaxial Speakers, 75W : Kicker 46CSC54 shown without grille.

    Kicker 46CSC54 : 75W 5.25" Coaxial Speakers

    Pre-Order Today!

    75-Watt 5 1/4-Inch Coaxial Speakers, 4-Ohm These CS series 5.25" coaxial speakers by Kicker are a significant upgrade in your sound. A stamped-steel speaker driver chassis supports a rigid polypropylene cone and UV-treated foam surrounds that stand up to heat and direct sunlight. These 75W coaxial's have neodymium tweeter magnets allow for increased volume in high frequencies. The Kicker CS series 5 and a 1/4" speakers work best with 75 watts of recommended power. Specifications Speaker Design 2 - way Woofer Size | in [mm] 5 1/4 [130] Tweeter Size | in [mm] 1/2 [13] DC Resistance | ohm 3.4 Peak Power | Watts 225 Continuous Power | Watts, RMS 75 Sensitivity [SPLo] | dB @ 1W, 1m 90 Effective Frequency Range | Hz 45-20k Mounting Hole Diameter | in [mm] 4 1/2 [115] Top Mount Depth | in [mm] 1/4 [7] Bottom Mount Depth | in [mm] 1 3/4 [45] Tweeter Protrusion | in [mm] 0 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam

    Pre-Order Today!

    $89.99

  • Sale -$45.00 Alpine S-S69 : 6x9" 85W RMS Coaxial Speakers

    Alpine S-S69 : 6x9" 85W RMS Coaxial Speakers - Discontinued

    2 Available for pickup

    Alpine 6X9-Inch Coaxial 2-WAY Speakers, 85-Watt RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specificatons 85W RMS/260W Peak Nominal Impedance 4Ω Frequency Response: 65-22kHz 1” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround CustomStamped Steel Frame 35mm voice coil Optional grille sold separately (KTE-S69G)

    2 Available for pickup

    $129.99$84.99

  • 3.5" 50W Coaxial Speakers : Kicker 47KSC3504 3.5" 50W Coaxial Speakers : Kicker 47KSC3504 front side.

    Kicker 47KSC3504 : 3.5" 50W Coaxial Speakers

    2 Available for pickup

    3-1/2" Coaxial Speaker Drivers, 50-Watt RMS The Kicker KS series three-and-a-half-inch coaxial speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 50 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Specifications Speaker Design 2-Way Woofer [in, mm] 3-½, 89 Tweeter [in, mm] ½, 13 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-50 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 80-20k Mounting Hole Diameter [in, mm] 3-1⁄16, 78 Top Mount Depth [in, mm] 1-5⁄8, 41.5 Bottom Mount Depth [in,mm] 1-7⁄8, 49 Tweeter Protrusion [in,mm] 3/16, 4 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

    2 Available for pickup

    $79.99

  • Alpine S-S40 : 4" 45W RMS Coaxial Speakers

    Alpine S-S40 : 4" 45W RMS Coaxial Speakers

    Pre-Order Today!

    Alpine 4-Inch Coaxial 2-Way Speakers, 45-Watts RMS The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are normally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. Alpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround which creates incredible linearity and colorization rejection. Specifications 45W RMS/140W Peak Nominal Impedance 4Ω Frequency Response: 97-22kHz 3/4” Silk Dome Tweeter CFRP (Carbon Fiber Reinforced Plastic) Cone H.A.M.R. Surround Custom Stamped Steel Frame 25mm voice coil

    Pre-Order Today!

    $79.99


You have seen 48 out of 52 products

Login

Forgot your password?

Don't have an account yet?
Create account