Alpine 45-Watts RMS x 4-Channel or 90-Watts x 2-Channel Universal Power-Pack Amplifier
Add higher output and more dynamic response with this easy-to-install Universal Power Pack upgrade.
Compact size lets the KTP-445U fit where most amplifiers won’t. The KTP-445U comes equipped with the RCA and Auto-Sensing-Speaker level connectors and it fits behind the head unit in the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. The size and flexible wires make the Power Pack an easy choice to save space.
High-Pass selectable switches for Front & Rear allow frequency filtering for a wide variety of speakers. Choose from full range to selectable range: 60Hz, 80Hz or 120Hz to fine-tune your crossover points.
Need configurable options for Speaker-Level or RCA inputs to the Power Pack? On the bottom panel of the Power Pack there are selectable input options to accommodate Speaker-Level (0.5V-10V) or RCA (0.2V – 4V) inputs. Selectable 2 Channel and 4 Channel options give you the control to determine source inputs, and can eliminate the need for Y-adapters.
The Power Pack provides simple variable gain controls on the end panel for flexibility and a wide variety of system applications.
In order to ensure that Alpine sound quality is heard at your ears, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The end result: The Power Pack boasts 1 Watt Signal-to-Noise Ratio of 82dB or better.
Uniquely, the Power Pack distortion actually decreases at higher frequencies, resulting in a clean and clear signal where your ear is most sensitive to distortion. - < 0.03% THD+N @ 1W, 1% THD+N @ rated power.
Features
45 Watts x 4 @ 4Ω/2Ω
90 Watts x 2 @ 4Ω Bridged
For aftermarket and factory installed systems
Compact size
Specifications
CEA-2006 Power Rating: 45W x 4 @ 4Ω/2Ω
90 Watts x 2 @ 4Ω Bridged
Alpine KTP-445U Manual
Alpine 45-Watts RMS x 4-Channel Head-Unit Power-Pack Amplifier
The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier.
Compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space.
In order to ensure that Alpine sound quality is heard, Alpine created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The end result: The Power Pack boasts 1 Watt Signal-to-Noise Ratio of 82dB or better.
Features
45 Watts x 4 @ 4Ω
For select 2005 and newer Alpine head units
Compact size
Specifications
CEA-2006 Power Rating: 45W x 4 @ 4Ω/2Ω
Mono Amplifier, 600-Watts at 2-Ohm, 300-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA8001t amplifier delivers as much as 600W into one bass channel.
Specifications
MODEL
CXA800.1
Power (watts/ch) 4 Ohm
300x1
Power (watts/ch) 2 Ohm
600x1
Power (watts/ch) 1 Ohm
800x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)8-1/8, 20.6
Frequency Response (Hz):
25-200, +0/-1dB
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
>95dB, a-weighted, re: rated power
Active Crossover:
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter:
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
Mono Amplifier, 300-Watts at 2-Ohm, 150-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA4001t amplifier delivers as much as 400W into one bass channel at 1-Ohm.
Specifications
MODEL
CXA400.1
Power (watts/ch) 4 Ohm
150x1
Power (watts/ch) 2 Ohm
300x1
Power (watts/ch) 1 Ohm
400x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm): (all models 2 3/8, 5.9H x 6 3/4, 17W x ...L)
8 1/8, 20.6
Frequency Response (Hz):
25-200, +0/-1dB
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
>95dB, a-weighted, re: rated power
Active Crossover:
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter:
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
JD-Series Monoblock Amplifier, 500-Watt @ 2-Ohm or 250-Watt @ 4-Ohm
Designed to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the JD500/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD500/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD500/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
250 W RMS x 1
@ 3 Ω
350 W RMS x 1
@ 2 Ω
500 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD500/1 Manual
RD-Series 5-Channel Automotive Amplifier, 70-Watts x 4ch + 500-Watt Mono @ 2-Ohm or 225-Watt @ 4-Ohm.
Crafted as an all-in-one, total system solution, the RD900/5 is engineered to power a complete audio system consisting of a subwoofer + four satellite system with 900 watts of high-performance sound. Equipped with JL's exclusive NexD™ switching technology, this complete power package efficiently generates a potent 70 watts of crystal-clear audio into 4 ohms, plus a robust 500 watts for a subwoofer system, all from a single compact chassis. Each pair of main channels is also fully bridgeable, stoutly producing 200 watts of full-range audio bliss (into 4 ohms), creating an ultra-powerful 3-channel amplifier.
Conveniently located on top of the RD900/5, you’ll find a complement of studio-grade signal processing features, all hidden beneath a removable protective cover. Each pair of main channels is equipped with a 12 dB / octave high-pass filter, with a dedicated low-pass filter for its subwoofer channel. All three crossovers offer continuously variable frequency selection from 50-500 Hz, for precise filtering. Dual-range, differential-balanced inputs are also onboard, capable of accepting most input voltage levels, plus automatic turn-on capability (via signal sensing or DC-offset sensing) for maximum versatility.
LED clipping indicators are also standard equipment for each channel section. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. The RD900/5 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of an RBC-1 remote level control (sold separately), you can conveniently control the subwoofer’s output remotely from the driver’s seat.
Specifications
Frequency Response (Main Channels)
12 Hz - 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
10 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Main Channels @ 4 Ω
70 W RMS x 4
Main Channels @ 2 Ω
100 W RMS x 4
Main Channels - Bridged @ 4Ω
200 W RMS x 2
Subwoofer Channel @ 4 Ω
225 W RMS x 1
Subwoofer Channel @ 3 Ω
325 W RMS x 1
Subwoofer Channel @ 2 Ω
500 W RMS x 1
Subwoofer Channel @ 1.5 Ω
N/A
JL Audio RD900/5 Manual
RD-Series 500-Watt Monoblock Subwoofer Amplifier @ 2-Ohms
Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is JL's proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion.
For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat.
Specifications
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
250 W RMS x 1
@ 3 Ω
350 W RMS x 1
@ 2 Ω
500 W RMS x 1
@ 1.5 Ω
N/A
JL Audio RD500/1 Manual
XDM-Series Five-Channel Class-D Marine-Grade Amplifier, 75-Watts x Four-Channels @ 4-Ohm and 300-Watt Mono @ 2-Ohm
The XDM700/5 is ideal for a complete audiophile-grade, subwoofer + four satellite system, and fits comfortably in just about any vehicle or vessel. With this incredible little amplifier, you can drive two pairs of quality component speaker systems with plenty of clean power (75W x 4 @ 4Ω), while also generating a solid 300W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's high-speed NexD switching amplifier design.
Suitable for car or boat installations, the XDM700/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
The XDM700/5 includes a 12dB / octave high-pass filter for one main channel pair, a 12dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500Hz or 500-5000Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
Main Channels @ 4 Ω
75 W RMS x 4 @ 14.4V
Main Channels @ 2 Ω
100 W RMS x 4 @ 14.4V
Main Channels - Bridged @ 4Ω
200 W RMS x 2 @ 14.4V
Subwoofer Channel @ 4 Ω
180 W RMS x 1 @ 14.4V
Subwoofer Channel @ 3 Ω
240 W RMS x 1 @ 14.4V
Subwoofer Channel @ 2 Ω
300 W RMS x 1 @ 14.4V
Subwoofer Channel @ 1.5 Ω
N/A
Main Channels @ 4 Ω
60 W RMS x 4 @ 12.5V
Main Channels @ 2 Ω
90 W RMS x 4 @ 12.5V
Main Channels - Bridged @ 4Ω
180 W RMS x 2 @ 12.5V
Subwoofer Channel @ 4 Ω
180 W RMS x 1 @ 12.5V
Subwoofer Channel @ 3 Ω
240 W RMS x 1 @ 12.5V
Subwoofer Channel @ 2 Ω
300 W RMS x 1 @ 12.5V
Subwoofer Channel @ 1.5 Ω
N/A
Frequency Response (Main Channels)
12 Hz - 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
10 Hz - 1 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Filter Mode(s): Channels 1 & 2 (front)
High-Pass only
Filter Slope(s): Channels 1 & 2 (front)
12 dB/octave
Filter Frequency Range: Channels 1 & 2 (front)
50 Hz - 5 kHz
Filter Mode(s): Channels 3 & 4 (rear)
High-Pass or Bandpass
Filter Slope(s): Channels 3 & 4 (rear)
12 dB/octave
Filter Frequency Range: Channels 3 & 4
50 Hz - 500 Hz
Filter Mode(s): Subwoofer Channel
Low-Pass only
Filter Slope(s): Subwoofer Channel
12/24 dB/octave
Filter Frequency Range: Subwoofer Channel
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Infrasonic Filter: Subwoofer Channel
none
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
Sub Ch. or All Channels
Channel Input Mode Switch
Yes (2/4/6 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
Height (H)
2.05 in / 52 mm
Width (W)
10.23 in / 260 mm
Depth (D)
7.09 in / 180 mm
Net Weight
6.15 lb / 2.79 kg
JL Audio XDM700/5 Manual
XDM-Series Monoblock Class-D Marine-Grade Amplifier, 600-Watts @ 2-Ohm or 400-Watts @ 4-Ohm
This potent monoblock amplifier employs JL-Audio's high-speed NexD switching design to achieve unprecedented efficiency and amazing power output from a very compact chassis. Don't let its small size fool you, though... the XDM/600/1 generates serious subwoofer power, delivering a full 600W of continuous power into a 2-ohm load (14.4V, 1% THD).
Designed for car or boat installations, the XDM600/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
Targeted specifically for subwoofer applications, the XDM600/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
400 W RMS x 1 @ 14.4V
@ 3 Ω
500 W RMS x 1 @ 14.4V
@ 2 Ω
600 W RMS x 1 @ 14.4V
@ 1.5 Ω
N/A
@ 4 Ω
300 W RMS x 1 @ 12.5V
@ 3 Ω
400 W RMS x 1 @ 12.5V
@ 2 Ω
500 W RMS x 1 @ 12.5V
@ 1.5 Ω
N/A
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>87 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>67 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Infrasonic Filter
30 Hz, defeatable
Bass Boost EQ
No
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
Height (H)
2.05 in / 52 mm
Width (W)
8.52 in / 216 mm
Depth (D)
7.09 in / 180 mm
Net Weight
6.3 lb / 2.86 kg
JL Audio XDM600/1 Manual
XDM-Series Five-Channel Class-D Marine-Grade Amplifier, 75-Watts x Four-Channels @ 4-Ohm and 600-Watt Mono @ 2-Ohm or 360-Watt @ 4-Ohm.
The XDM1000/5 delivers up to 1000W of clean power and is ideal for an audiophile-grade, subwoofer + four satellite system. With this potent powerhouse, you can drive two pairs of quality component speaker systems with plenty of clean power (75W x 4 @ 4Ω), while also generating a stout 600W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's high-speed NexD switching amplifier design.
Suitable for car or boat installations, the XDM1000/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
The XDM1000/5 includes a 12dB / octave high-pass filter for one main channel pair, a 12dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500Hz or 500-5000Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
Main Channels @ 4 Ω
75 W RMS x 4 @ 14.4V
Main Channels @ 2 Ω
100 W RMS x 4 @ 14.4V
Main Channels - Bridged @ 4Ω
200 W RMS x 2 @ 14.4V
Subwoofer Channel @ 4 Ω
400 W RMS x 1 @ 14.4V
Subwoofer Channel @ 3 Ω
500 W RMS x 1 @ 14.4V
Subwoofer Channel @ 2 Ω
600 W RMS x 1 @ 14.4V
Subwoofer Channel @ 1.5 Ω
N/A
Main Channels @ 4 Ω
60 W RMS x 4 @ 12.5V
Main Channels @ 2 Ω
90 W RMS x 4 @ 12.5V
Main Channels - Bridged @ 4Ω
180 W RMS x 2 @ 12.5V
Subwoofer Channel @ 4 Ω
360 W RMS x 1 @ 12.5V
Subwoofer Channel @ 3 Ω
480 W RMS x 1 @ 12.5V
Subwoofer Channel @ 2 Ω
600 W RMS x 1 @ 12.5V
Subwoofer Channel @ 1.5 Ω
N/A
Frequency Response (Main Channels)
12 Hz - 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
10 Hz - 1 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Filter Mode(s): Channels 1 & 2 (front)
High-Pass only
Filter Slope(s): Channels 1 & 2 (front)
12 dB/octave
Filter Frequency Range: Channels 1 & 2 (front)
50 Hz - 5 kHz
Filter Mode(s): Channels 3 & 4 (rear)
High-Pass or Bandpass
Filter Slope(s): Channels 3 & 4 (rear)
12 dB/octave
Filter Frequency Range: Channels 3 & 4
50 Hz - 500 Hz
Filter Mode(s): Subwoofer Channel
Low-Pass only
Filter Slope(s): Subwoofer Channel
12/24 dB/octave
Filter Frequency Range: Subwoofer Channel
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Infrasonic Filter: Subwoofer Channel
none
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
Sub Ch. or All Channels
Channel Input Mode Switch
Yes (2/4/6 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
Height (H)
2.05 in / 52 mm
Width (W)
14.73 in / 374 mm
Depth (D)
7.09 in / 180 mm
JL Audio XDM1000/5v2 Manual
JD-Series 75-Watt x 4-Channel Class-D Full-Range Amplifier
Utilizing JL Audio's exclusive NexD™ high-speed switching technologies, the JD400/4 amplifier is engineered to deliver loads of clean power, with excellent efficiency and low distortion. This little guy churns out 100 watts of audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms.
The JD400/4’s controls can be found on the input panel of the amplifier, with all speaker and power connections located along the opposite end of the extruded aluminum chassis. Signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting line-level or speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment.
Onboard LED-clipping indicators are also included surrounding each input sensitivity control. This convenient feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. You will also find a set of buffered, pass-through preamp outputs on-board, so you can pass signals to another amplifier.
General Specifications
@ 4 Ω
75 W RMS x 4
@ 2 Ω
100 W RMS x 4
Bridged @ 4Ω
200 W RMS x 2
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
No
Filter Defeat Function
Yes
Remote Level Control
No
Remote Level Modes
N/A
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
No (always 2 Ch)
JL Audio JD400/4 Manual
JD-Series Monoblock Amplifier, 1000-Watt @ 2-Ohm or 600-Watt @ 4-Ohm
Designed to produce a serious 1000 watts into 2 ohms (14.4V, 1% THD), the JD1000/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD1000/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD1000/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
600 W RMS x 1
@ 3 Ω
800 W RMS x 1
@ 2 Ω
1000 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD1000/1 Manual
Alpine HD-Series Mono Class-D Full-Range Hi-Resolution Automotive-Grade Amplifier, 800-Watts @ 2-Ohms or 500-Watts @ 4-Ohms
Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status System features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24Bit playback.
Powering a Hi-Res sound system without contributing noise during playback requires efficiency and precision and the HDA-M80 was intentionally designed to provide impressive power output to the system while ensuring the purest audio performance. The amplifier’s wide dynamic range capability provides impressive output in a compact chassis that fits most vehicle applications.
The HDA-M80 features a high-efficiency digital circuit design that ensures ultra- low distortion levels for precise sound reproduction and superb sound quality. Intentional designs, like a copper-plated chassis and black circuit board, bring the signal-to-noise ratio up to 83dB and minimize noise and distortion during playback for complete music fidelity that’s true to the original source.
Featuring technology unique to Alpine, the amplifier features Alpine’s dual negative feedback control circuit to improve linearity for the most accurate sound amplification. This technology also stabilizes the amplifier output while driving the subwoofers for ultimate reliability.
The HDA- M80 features Alpine’s quick- connect power and speaker connectors for quick and safe installation. The one- sided terminal layout and top-panel sound controls give the user quick access to controls on the amplifier.
The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System.
Features
Hi-Res Audio Playback (192kHz/24Bit)
Mono-Channel Amplifier
High-Efficiency Digital Circuit Design
Alpine’s Dual Negative Feedback Control Circuit
High Bandwidth Amplifier
Alpine’s Premium Class D Circuit Design
Copper-plated chassis
Black circuit board
One-sided terminal layout
Top panel sound controls
Quick connect power and speaker terminals
Optional Remote bass knob compatible (requires RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 11.4375” x 7.5” x 2.125”
Power Rating: (14.4V, ≤1.0% THD+N)
800W x 1 @ 2Ω
500W x 1 @ 4Ω
THD+N: 0.02% (10W into 4ohm)
S/N Ratio: 83dB (1W into 4ohm)
Frequency response: 8-400Hz (-3dB)
Damping factor: 1500
Selectable input level – HI/LO
Variable High pass / Low pass crossover
Variable Subsonic filter
Bass EQ (0 to +12dB, Variable)
Auto-turn on with remote sensing
Alpine HDA-M80 Manual
MX-Series 4-Channel Class-D Marine-Grade Amplifier, 70-Watts x 4ch @ 2-Ohm or 50-Watts x 4ch @ 4-Ohm
Engineered specifically for powersports applications, the 4-channel MX280/4 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 50W x 4 into 4 ohms (14.4V, 1% THD), the MX280/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 140W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>89.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>60 / 50 Hz
Damping Factor @ 2 Ω
>30 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
35 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
50 W RMS x 4
@ 2 Ω
70 W RMS x 4
Bridged @ 4Ω
140 W RMS x 2
JL Audio MX280/4 Manual
MX-Series 300-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 160-Watt @ 4-Ohm
Engineered specifically for powersports applications, the MX300/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 300W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX300/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 12 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
160 W RMS x 1
@ 3 Ω
220 W RMS x 1
@ 2 Ω
300 W RMS x 1
@ 1.5 Ω
N/A
JL Audio MX300/1 Manual
Mono Amplifier, 1200-Watts at 2-Ohm, 600-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA12001t amplifier delivers as much as 1,200W into one bass channel.
Specifications
MODEL
CXA1200.1
Power (watts/ch) 4 Ohm
600x1
Power (watts/ch) 2 Ohm
1200x1
Power (watts/ch) 1 Ohm
1200x1 +/-10%
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)12, 30.6
Frequency Response (Hz):
25-200Hz
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
95dB
Active Crossover:
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter:
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
4-Channel Class-D Full-Range Amplifier with Integrated DSP, 100-Watt x 4 @2-Ohm / 75-Watt x 4 @ 4-Ohm
Designed to simplify great audio, every VXi amplifier combines JL's advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
With JL's second-generation NexD2™ technology, the VX400/4i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up to 200 W x 2.
The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
Amplifier includes: Power Connector (for 4 AWG wire), Analog Input/Pre-Out Harness, Speaker Output Harness, 6 ft A/B USB Cable
TüN™ Software Applications
Intuitive setup and tuning, all at your fingertips. Automatically recognizes connected amplifier and displays appropriate interface. TüN™ is available for download for free in a variety of applications, for computers and most handheld devices.
Unprecedented, Onboard DSP Tuning Power
Premium, triple-core AKM® DSP with an optimized configuration, developed in collaboration with AKM®
Hi-Res audio processing at 24 bit/96 kHz
High-performance AKM® A/D and D/A converters
10 Bands of fully parametric EQ, per output channel, including pre-outs
Shelving EQ option for Band 1 and Band 10
High-Pass & Low-Pass Filters for each output channel, with selectable alignments and slopes: Linkwitz-Riley: 12, 24, 48 dB/octaveButterworth: 6, 12, 18, 24, 36, 48 dB/octave
Signal Delay in 0.01 millisecond steps (equivalent to 1/8-inch, 3 mm)
All-Pass Filter (Phase EQ), with variable "Q" and corner frequency
Polarity Reversal (0 or 180 deg.)
Output Level Trim in 0.1 dB steps
NexD2™ Switching Amplifier Technology
JL's latest generation of high-speed switching technology delivers superb low frequency power and efficiency.
Specially optimized for subwoofer applications
Ultra-Versatile Analog and Digital Inputs
High-performance, differential-balanced analog inputs for outstanding noise rejection
Accepts speaker level signals from 200 mV, up to 16V RMS, including those from many factory systems
Optical Digital (Toslink) input permits direct connection of S/PDIF digital sources, bypassing A/D converter. Accepts up to 24 bit/192 kHz input.
Independently configurable RCA analog and digital pre-outs (24 bit/96 kHz)
Automatic turn-on options via Signal-Sensing or DC-Offset sensing
Functional Compact Chassis Design
Solid cast alloy main unibody and bottom plate deliver superb EMI performance and shielding
All connections utilize compact mating connectors for maximum integrity and fitment into tight spaces.
Configurable LED logo ring displays status and can display audio preset color code or user-defined color
Logo badge can be oriented in 90 degree increments
Corner caps engineered to conceal mounting holes and hardware
JLid™ System Command and Control with Networking Capabilities
JL Audio's digital protocol provides control interface and communication between VXi amplifiers and optional JLid™ accessories, including:
DRC-100/DRC-200/DRC-205 Digital Remote Controllers: Offers convenient level and DSP preset control from the driver's seat.
VXi-BTC Bluetooth® Communicator: Permits wireless configuration of VXi amplifiers using your compatible Apple® or Android® device.
VXi-HUB Optical Network Hub: Provides network connectivity for up to five slave VXi amplifiers, allowing synchronization of DRC controllers and DSP presets. Up to two VXi-HUBs can be daisy-chained to network up to ten VXi amplifiers.
Specifications
Frequency Response
12 Hz - 24 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power(Analog Inputs)
99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W(Analog Inputs)
80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to highest rated power(Digital Inputs)
101 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W(Digital Inputs)
81 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>100 / 50 Hz
Damping Factor @ 2 Ω
>50 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 16 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
75 W RMS x 4
@ 2 Ω
100 W RMS x 4
Bridged @ 4Ω
200 W RMS x 2
JL Audio VX400/4i Manual
5-Channel Class-D System Amplifier with Integrated DSP, 100-Watt x 4 @ 2-Ohm + 600-Watt x 1 @ 2-Ohm
Employing JL's second generation NexD2™ amplifier technology, the VX1000/5i efficiently powers a complete audio system. It can drive four main speakers with 75 W x 4 @ 4 ohms while also powering a subwoofer with up to 600W @ 2 ohms. Bridging the main channels converts it into a very powerful, 3-channel system amplifier with up to 200W x 2 @ 4 ohms on the main channels and 600W @ 2 ohms on the subwoofer channel.
The NexD2™ full-range technology in the main channels of this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The subwoofer channel features an optimized low-frequency variant of the NexD2™ technology. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
Amplifier includes: Power Connector (for 2 AWG wire), Analog Input/Pre-Out Harness, Speaker Output Harness, Subwoofer Output Connector, 6 ft A/B USB Cable.
TüN™ Software Applications
Intuitive setup and tuning, all at your fingertips. Automatically recognizes connected amplifier and displays appropriate interface. TüN™ is available for download for free in a variety of applications, for computers and most handheld devices.
Unprecedented, Onboard DSP Tuning Power
Premium, triple-core AKM® DSP with an optimized configuration, developed in collaboration with AKM®
Hi-Res audio processing at 24 bit/96 kHz
High-performance AKM® A/D and D/A converters
10 Bands of fully parametric EQ, per output channel, including pre-outs
Shelving EQ option for Band 1 and Band 10
High-Pass & Low-Pass Filters for each output channel, with selectable alignments and slopes: Linkwitz-Riley: 12, 24, 48 dB/octaveButterworth: 6, 12, 18, 24, 36, 48 dB/octave
Signal Delay in 0.01 millisecond steps (equivalent to 1/8-inch, 3 mm)
All-Pass Filter (Phase EQ), with variable "Q" and corner frequency
Polarity Reversal (0 or 180 deg.)
Output Level Trim in 0.1 dB steps
NexD2™ Switching Amplifier Technology
JL's latest generation of high-speed switching technology delivers superb low frequency power and efficiency.
Specially optimized for subwoofer applications
Ultra-Versatile Analog and Digital Inputs
High-performance, differential-balanced analog inputs for outstanding noise rejection
Accepts speaker level signals from 200 mV, up to 16V RMS, including those from many factory systems
Optical Digital (Toslink) input permits direct connection of S/PDIF digital sources, bypassing A/D converter. Accepts up to 24 bit/192 kHz input.
Independently configurable RCA analog and digital pre-outs (24 bit/96 kHz)
Automatic turn-on options via Signal-Sensing or DC-Offset sensing
Functional Compact Chassis Design
Solid cast alloy main unibody and bottom plate deliver superb EMI performance and shielding
All connections utilize compact mating connectors for maximum integrity and fitment into tight spaces.
Configurable LED logo ring displays status and can display audio preset color code or user-defined color
Logo badge can be oriented in 90 degree increments
Corner caps engineered to conceal mounting holes and hardware
JLid™ System Command and Control with Networking Capabilities
JL Audio's digital protocol provides control interface and communication between VXi amplifiers and optional JLid™ accessories, including:
DRC-100/DRC-200/DRC-205 Digital Remote Controllers: Offers convenient level and DSP preset control from the driver's seat.
VXi-BTC Bluetooth® Communicator: Permits wireless configuration of VXi amplifiers using your compatible Apple® or Android® device.
VXi-HUB Optical Network Hub: Provides network connectivity for up to five slave VXi amplifiers, allowing synchronization of DRC controllers and DSP presets. Up to two VXi-HUBs can be daisy-chained to network up to ten VXi amplifiers.
Specifications
Frequency Response (Main Channels)
12 Hz - 24 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Analog Inputs - Main Channels)
99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Frequency Response (Subwoofer Channel)
12 Hz - 1 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Analog Inputs - Subwoofer Channel)
99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Analog Inputs - Main Channels)
80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Analog Inputs - Subwoofer Channel)
72 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to highest rated power (Digital Inputs - Main Channels)
100 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to highest rated power (Digital Inputs - Subwoofer Channel)
99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Digital Inputs - Main Channels)
81 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Digital Inputs - Subwoofer Channel)
73 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 2 Ω
>50 / 50 Hz
Damping Factor @ 4 Ω
>150 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 16 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Main Channels @ 4 Ω
75 W RMS x 4
Main Channels @ 2 Ω
100 W RMS x 4
Main Channels - Bridged @ 4Ω
200 W RMS x 2
Subwoofer Channel @ 4 Ω
400 W RMS x 1
Subwoofer Channel @ 3 Ω
500 W RMS x 1
Subwoofer Channel @ 2 Ω
600 W RMS x 1
Subwoofer Channel @ 1.5 Ω
N/A
JL Audio VX1000/5i Manual
JD-Series Monoblock Amplifier, 500-Watt @ 2-Ohm or 250-Watt @ 4-Ohm
Designed to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the JD500/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD500/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD500/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
250 W RMS x 1
@ 3 Ω
350 W RMS x 1
@ 2 Ω
500 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD500/1 Manual
JD-Series 75-Watt x 4-Channel Class-D Full-Range Amplifier
Utilizing JL Audio's exclusive NexD™ high-speed switching technologies, the JD400/4 amplifier is engineered to deliver loads of clean power, with excellent efficiency and low distortion. This little guy churns out 100 watts of audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms.
The JD400/4’s controls can be found on the input panel of the amplifier, with all speaker and power connections located along the opposite end of the extruded aluminum chassis. Signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting line-level or speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment.
Onboard LED-clipping indicators are also included surrounding each input sensitivity control. This convenient feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. You will also find a set of buffered, pass-through preamp outputs on-board, so you can pass signals to another amplifier.
General Specifications
@ 4 Ω
75 W RMS x 4
@ 2 Ω
100 W RMS x 4
Bridged @ 4Ω
200 W RMS x 2
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
No
Filter Defeat Function
Yes
Remote Level Control
No
Remote Level Modes
N/A
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
No (always 2 Ch)
JL Audio JD400/4 Manual
R2-Series Mono Class-D Full-Range Automotive-Grade Amplifier, 750-Watts x 1-Channel @ 2-Ohm or 500-Watts x 1-Channel @ 4-Ohm
Elevate your audio with the Alpine R2-A75M Mono Amplifier - delivering powerful 750W performance in a sleek, compact design. Built with Alpine's cutting-edge Class D Amplifier Circuit, this next-generation R-Series amp offers exceptional sound quality and efficiency, making it the perfect addition to any car audio system.
The R2-A75M features a reduced footprint that’s 15% smaller than the previous model (R-A75M), making it easier than ever to install in most vehicle applications while still getting the same powerhouse performance.
The R2-A75M features intentional design choices that prioritize convenience and simplicity. All speaker connections are consolidated on one side of the device for easy access, while the amplifier controls have been relocated to the top under a removable plate, allowing for quick adjustments to gain and crossover controls. The amplifier's chassis also includes integrated mounting "feet" to streamline the installation process.
Specifications
Dimensions: 11.1” W x 2.17” H x 6.5” D
Weight: 7 lbs, 10 oz
Power Rating: 14.4V, ≤ 1% THD +N
Power Output: 500W RMS x 1 @ 4Ω, 750W RMS x 1 @ 2Ω
S/N Ratio: >75dB
Frequency Response: 10Hz – 400Hz
Damping Factor: >250
Alpine R2-A75M Manual
JD-Series Monoblock Amplifier, 1000-Watt @ 2-Ohm or 600-Watt @ 4-Ohm
Designed to produce a serious 1000 watts into 2 ohms (14.4V, 1% THD), the JD1000/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD1000/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD1000/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
600 W RMS x 1
@ 3 Ω
800 W RMS x 1
@ 2 Ω
1000 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD1000/1 Manual
Five-Channel Amplifier, 65-Watts x 4ch +, 300-Watts x 1ch at 2-Ohm or 150W @ 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA6605t amplifier delivers as much as 300W into one bass channel.
Specifications
MODEL
CXA660.5
Power (watts/ch) 4 Ohm Stereo
65x4
Power (watts/ch) 2 Ohm Stereo
90x4
Power (watts/ch) 4 Ohm Mono
180x2
Power (watts/ch) 4 Ohm Mono Sub Ch
150x1
Power (watts/ch) 2 Ohm Mono Sub Ch
300x1
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17 W x ...L)14-1/8, 35.7
Frequency Response (Hz):
10Hz-20kHz
Frequency Response (Hz – Sub Ch.):
25Hz-200Hz
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
90dB
Active Crossover:
Amp 1-2: High Pass 10-200Hz @ 12dB/OctaveSub Channel: Low Pass 50-200Hz @ 12dB/Octave
Subsonic Filter:
25Hz @24dB/Octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker 46CXA6605t Manual
HD-Series Monoblock Class-D Wide-Range Amplifier, 750-Watts x 1ch @ 1.5-4-Ohms
This ultra-compact monoblock amplifier employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 750W of clean power into any impedance between 1.5 and 4Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, JL invites you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price.
While targeted primarily to subwoofer applications, the HD750/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems.
This amplifier features a brushed aluminum finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.
General Specifications
Frequency Response
6 Hz - 8 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>110 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Main Channels)
>88 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>500 / 50 Hz
Damping Factor @ 2 Ω
>250 / 50 Hz
THD+N @ Rated Power (Main Channels)
<0.03% @ 4 Ω
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
750 W RMS x 1
@ 3 Ω
750 W RMS x 1
@ 2 Ω
750 W RMS x 1
@ 1.5 Ω
750 W RMS x
JL Audio HD750/1 Brochure
JD-Series Monoblock Amplifier, 250-Watt @ 2-Ohm or 150-Watt @ 4-Ohm
Designed to produce a healthy 250 watts into 2 ohms (14.4V, 1% THD), the JD250/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD250/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD250/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you easily set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
150 W RMS x 1
@ 3 Ω
200 W RMS x 1
@ 2 Ω
250 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD250/1 Manual
Alpine S2-Series 5-Channel Amplifier, 60-Watt x 4-Channel + 300-Watt Sub @ 2Ω, or 40-Watt x 4-Channel + 200-Watt Sub @ 4Ω
The Next-Gen Alpine S-Series S2-A55V 5-Channel Amplifier is Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth coupled with the elevated S-Series design brings out a new benchmark for entry-level performance and price.
The Next-Gen S-Series Amplifiers now feature a new selectable remote turn-on circuit, a three-position switch that ensures the amplifier turns on and off at the proper times. This design is crucial with newer, in-vehicle technology and allows for proper integration with any factory or aftermarket system.
The amplifier was intentionally designed with sound controls located on the side panels, instead of the top panel, making it easier to access gain and crossover controls when installed under vehicle seats or in shallow-depth locations. Removable end caps were added to cover the side controls and connections, providing a clean, sleek finish to the amplifier.
With its versatile 5-Channel design, the S2-A55V Amplifier is the perfect solution to power your sound system all in a single chassis. This amplifier delivers crisp and clear audio to up to four speakers plus an additional subwoofer to give your system a complete audio upgrade.
Features
Hi-Res Audio Certified (Up to 40kHz)
5-Channel Amplifier
Alpine’s Class D Amplifier Circuit
Two-sided terminal layout
Built-in Selectable/ Adjustable Crossovers
Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 11.9” W x 2.25” H x 8.25” D
Weight: 7 lbs
Power Rating: 14.4V, < 0.1% THD +N
Power Output: 40W x 4 + 200W x 1 @ 4Ω, 60W x 4 + 300W x 1 @ 2Ω
Bridged Power: 120W RMS x 2 @ 4Ω
S/N Ratio: >83dB
Frequency Response: 20Hz – 40kHz
Damping Factor: >100
Alpine S2-A55V Manual
Alpine S2-Series 90-Watt x 4-Channel Power Amplifier @ 2-Ohm or 60-Watt x 4-Channel @ 4-Ohm
The Next-Gen Alpine S-Series S2-A36F 4-Channel Amplifier is Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth coupled with the elevated S-Series design brings out a new benchmark for entry-level performance and price.
The Next-Gen S-Series Amplifiers now feature a new selectable remote turn-on circuit, a three-position switch that ensures the amplifier turns on and off at the proper times. This design is crucial with newer, in-vehicle technology and allows for proper integration with any factory or aftermarket system.
The amplifier was intentionally designed with sound controls located onthe side panels, instead of the top panel, making it easier to access gain and crossover controls when installed under vehicle seats or in shallow-depth locations. Removable end caps were added to cover the side controls and connections, providing a clean, sleek finish to the amplifier.
With its new and unique variable Mid-Bass EQ Circuit, the S2-A36F allows you to dial in the mid-bass impact as desired, making it an ideal choice for those seeking a more dynamic and powerful audio experience.
Features
Hi-Res Audio Certified (Up to 40kHz)
4-Channel Amplifier
Alpine’s Class D Amplifier Circuit
Two-sided terminal layout
Built-in Selectable/ Adjustable Crossovers
Variable Mid-Bass EQ Circuit for more upper bass impact
Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 8.7” W x 2.25” H x 8.25” D
Weight: 4 lbs, 13 oz
Power Rating: 14.4V, ≤ 0.1% THD +N
Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω
Bridged Power: 180W RMS x 2 @ 4Ω
S/N Ratio: >83dB
Frequency Response: 20Hz – 40kHz
Damping Factor: >100
Alpine S2-A36F Manual
Alpine S2-Series Subwoofer Amplifier, 600-Watts Mono @ 1 or 2-Ohm or 330-Watts @ 4-Ohm Impedance
Alpine's S-Series S2-A60M 600W Mono Amplifier is the perfect solution for unparalleled power and performance on a budget. With a power output of 600W at a 1ohm or 2ohm drive, this mono amp is capable of driving even the most demanding subwoofers, delivering clean and distortion-free bass for a wide range of applications. Plus, its compact design makes it easy to install in any vehicle.
New to the Next-Generation S-Series amplifiers is a new selectable remote turn-on circuit, a three-position switch that ensures the amplifier turns on and off at the proper times. This design is crucial with newer, in-vehicle technology and allows for proper integration with any factory or aftermarket system.
The amplifier was intentionally designed with sound controls located on the side panels, instead of the top panel, making it easier to access gain and crossover controls when installed under vehicle seats or in shallow-depth locations. Removable end caps were added to cover the side controls and connections, providing a clean, sleek finish to the amplifier.
With the capacity to deliver 600 watts of power at 1ohm, the S2-A60M is fully equipped to provide ample power to either a single Alpine S-Series 10" or 12" Subwoofer, or two S-Series 8" Subwoofers, ensuring exceptional sound quality and optimal performance.
Features
600W Mono Power Amplifier
Alpine’s Class D Amplifier Circuit
Two-sided Terminal Layout
Built-in Selectable / Adjustable Crossovers
Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 8.7” W x 2.25” H x 8.25” D
Weight: 4 lbs, 13 oz
Power Rating: 14.4V, < 0.1% THD +N
Power Output: 330W RMS x 1 @ 4Ω, 600W RMS x 1 @ 2Ω, 600W RMS x 1 @ 1Ω
S/N Ratio: >85dB
Frequency Response: 10Hz – 400Hz
Damping Factor: >1000
Alpine S2-A60M Manual
Alpine R2-Series 100-Watt x 4-Channel Amplifier @ 4-Ohms or 150-Watt x 4-Channel @ 2-Ohms
The Next-Generation R-Series Amplifiers are Hi-Res Audio Certified and able to reproduce up to 45kHz frequency response. This ultra-wide bandwidth brings music even closer to the original source while the classic R-Series design maintains the “loud and fun” performance quality that long-time fans have come to enjoy.
The R2-A60F features a reduced footprint that’s 15% smaller than the previous model (R-A60F), making it easier than ever to install in most vehicle applications while still getting the same powerhouse performance.
Intentional designs were made to the amplifier that consolidated all speaker connections to one side of the amplifier for easy access. Amplifier controls were relocated to the top of the amplifier under a removable plate for convenient access to gain and crossover controls. To simplify the installation process, mounting "feet" are integrated onto the chassis of the amplifier.
Features
Hi-Res Audio Certified (Up to 45kHz)
4-Channel Amplifier
Alpine’s Class D Amplifier Circuit
Reduced Footprint (15% smaller compared to the previous R-A60F model)
One-Sided Terminal Layout
Top Panel Sound Controls
Integrated Mounting Feet for Simple Installation
Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 11.1” W x 2.17” H x 6.5” D
Weight: 7 lbs, 3 oz
Power Rating: 14.4V, ≤ 1% THD +N
Power Output: 100W x 4 @ 4Ω, 150W x 2 @ 2Ω
Bridged Power: 300W x 2 @ 4Ω
S/N Ratio: >80dB
Frequency Response: 10Hz – 45kHz
Damping Factor: >10
Alpine R2-A60F Manual
XDM-Series Six-Channel Class-D Marine-Grade Amplifier, 100-Watts x Six-Channels @ 2-Ohm or 75-Watts x 6-Channels @ Four-Ohm
The incredibly flexible XDM600/6 packs a serious full-range wallop and delivers a stunning 100-watts to each of its six channels into 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is Jl's advanced NexD high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency.
Suitable for car or boat installations, the XDM600/6 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
With the XDM600/6, you have plenty of great use options. Configure it as a six-channel satellite amplifier with 75W x 6 @ 4Ω, or bridge four of its channels to create a staggered power four-channel amplifier with 200W x 2 @ 4Ω for your front satellites and 75W x 2 @ 4Ω for your rear satellites. You can also drive two subwoofers with 200W each, plus a pair of satellites with 75W x 2.
The XDM600/6 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all six amplifier channels directly from the driver's seat or cockpit.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
75 W RMS x 6 @ 14.4V
@ 2 Ω
100 W RMS x 6 @ 14.4V
Bridged @ 4Ω
200 W RMS x 3 @ 14.4V
@ 4 Ω
60 W RMS x 6 @ 12.5V
@ 2 Ω
90 W RMS x 6 @ 12.5V
Bridged @ 4Ω
180 W RMS x 3 @ 12.5V
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
2 or 4 or All Channels
Channel Input Mode Switch
Yes (2/4/6 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
Height (H)
2.05 in / 52 mm
Width (W)
10.23 in / 260 mm
Depth (D)
7.09 in / 180 mm
Net Weight
5.8 lb / 2.63 kg
JL Audio XDM600/6v2 Manual
R-Series 6-Channel Class-D Full-Range Hi-Resolution Automotive-Grade Amplifier, 75-Watts x 4-Channel + 150-Watt Mono @ 4-Ohms, or 100-Watts x 4-Channel + 250-Watt Mono @ 2-Ohms
The R-A90S has a unique staggered power channel layout that has double the power on the last two channels. When looking to power a dual subwoofer configuration, the R-A90S’s 5th and 6th channels can be bridged to provide up to 500-watts at 4Ω. The R-A90S is matched in power and performance for the Dual 10-inch Alpine Halo S-Series Preloaded Subwoofer Enclosures with ProLink™.
Thanks to the unique staggered power channel layout, the R-A90S can host different levels of power on each channel, compared to traditional, multi-channel amplifiers. This allows the R-A90S to grow with you as it can effectively function as both a 3-way active amplifier and a 5-channel amplifier by delivering the power you need to the channels where you need it the most.
Hear the subtle details you’ve been missing in your music. The R-A90S maintains an extremely low phase shift throughout the music spectrum, which minimizes audible imperfections in your music and allows your music to stay faithful to the original recording. With a hi-resolution frequency response, the R- A90S can reproduce sound with incredible accuracy that stays true to the artist’s intention.
Using custom Alpine internal components originally launched in Alpine’s premium X-Series amplifiers, the R-A90S has dual post-filter feedback loops that correct signal distortion by making the output as close as possible to the original input for accurate sound reproduction.
For the best possible sound experience, use the built-in bandpass, high pass, or low pass filter to individually power each component in your sound system and assign frequency bands for accurate and reliable sound reproduction.
The R-A90S has input capability to add an optional RUX-KNOB.2 Remote Bass Control Knob (sold separately). The remote bass knob controls the bass in your subwoofer by adjusting the gain on your amplifier for quick bass adjustments when needed.
Alpine’s R-Series line of speakers, subwoofers, and amplifiers have a heritage of sound quality that can be heard from a block away. The R-A90S is tuned to emphasize the characteristics of the R- Series speakers and subwoofers for a legendary R-Series experience.
Features
6-Channel Amp with 5-Channel Power– With double the power on the last two channels, the R-A90S’s 5th and 6th channels can be bridged to provide up to 500-watts at 4Ω to a subwoofer system such as a pair of S-SB12Vs.
An Amp that Grows with You – When you’re ready to upgrade your Alpine system, use the R-A90S to amplify a 3-way active system with enough mid-bass power to create the up-front bass impact you crave.
Accurate Sound Reproduction – With incredibly low phase shift and hi-resolution frequency response, the R-A90S can reproduce sound with incredible accuracy that stays true to the artist’s intention.
Specifications
Dimensions: 12.75" x 10.75" x 2"
Hi-Resolution Audio Compliant (40k Hz)
Alpine’s Class D Amplifier Circuit
75W x 4 + 150W x 2 (4Ω, 14.4V, < 1% THD +N)
100W x 4 + 250W x 2 (2Ω, 14.4V, < 1% THD +N)
Bridged: 200W x 2 + 500W x 1 (4Ω, 14.4V, < 1% THD +N)
S/N > 85dB (ref. 1W into 4Ω)
THD + N < 0.03% (ref. 10W into 4Ω)
Frequency response: 10-45kHz (0/-3dB)
Damping factor > 500
CTA-2006
Alpine R-A90S Manual
Alpine HD-Series 12-Channel Class-D Full-Range Hi-Resolution Automotive-Grade Amplifier, 50-Watts x 8-Channel + 80-Watt x 4-channel @ 4-Ohms
Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status system features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24bit playback.
Building a sound system while overcoming acoustical challenges in the interior environment of the vehicle is no easy feat, however, the HDP-D90 14-Channel Hi-Res Digital Sound Processor Amplifier provides flexible system building and Hi-Res processing power up to 192kHz/24 Bit for an infallible listening experience.
Custom developed for Hi-Res Playback, the HDP-D90 has a 192kHz/64Bit internal sampling rate and an ultra-wide audio bandwidth of 10Hz-110kHz for recording studio-level sound. Intentional designs, like a copper-plated chassis, bring the signal-to-noise ratio up to >110dB and minimize noise and distortion during playback for complete music fidelity that’s true to the original source.
The HDP-D90 includes multiple source inputs for flexible system building for the option to retain a factory head unit, add an aftermarket head unit, or the Alpine Status HDS-990 Digital Media Controller. For older vehicles with no source player, the HDP-D90 can also function as a standalone music source and can receive music sent directly from a smartphone with Bluetooth® wireless streaming.
When paired with the Hi-Res HDS-990 Digital Media Player, you unlock even more control options for your processor while getting the highest-quality playback possible in your vehicle.
With 12-channels of amplifier outputs, the HDP-D90 can be used as a standalone source to power a 2-Way Speaker System, or for a more dynamic listening experience, includes 10- channels of RCA output for adding additional amplifiers to power a 3-way speaker system.
The Alpine Status System is sold separately and can be used to build a custom sound system. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System.
Features
High-Performance 14-Channel Digital Sound Processor Amplifier
Hi-Res Audio Playback (192kHz/24Bit)
PC Tuning Application
Selectable pre-configured sound system configurations
Embedded RTA signals for sound tuning
Bluetooth® audio streaming with included external module
Optional Controller
Specifications
Hi-Res Audio Playback (192kHz/24Bit)
14-Channel Inputs (All DSP control)
Inputs: 12-Channel Hi-level/2-Channel RCA/Optical (SPDIF)/Coaxial (Digital)
Outputs: 10-Channel RCA output/ 12-Channel High-Level amplified outputs (50W x 8 @ 4ohm + 80W x 4 @4ohm)
31 Band Parametric or Graphic EQ
Channel mixing by Matrix Input Summing
Sampling Rate = Internal: 192kHz/32Bit
S/N: >110dB, THD: <0.001%
Hi pass/low pass crossover per channel
Time correction: up to7mm delay per channel
Sigma DSP (ADAU1467x2)
Alpine HD-Series 4-Channel Class-D Full-Range Hi-Resolution Automotive-Grade Amplifier, 100-Watts x 4ch @ 4-Ohms or 150-Watts @ 2-Ohms
Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res AlpineF#1Status system technologies, the Alpine Status System features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24Bit playback.
Powering a Hi-Res sound system without contributing noise during playback requires efficiency and precision and the HDA-F60 was intentionally designed to provide impressive power output to the system while ensuring the purest audio performance. The amplifier’s wide dynamic range capability provides impressive output in a compact chassis that fits most vehicle applications.
The HDA-F60 features a high-efficiency digital circuit design that ensures ultra- low distortion levels for precise sound reproduction and superb sound quality. Intentional designs, like a copper-plated chassis and black circuit board, bring the signal-to-noise ratio up to 83dB and minimize noise and distortion during playback for complete music fidelity that’s true to the original source.
Featuring technology unique to Alpine, the amplifier features Alpine’s dual negative feedback control circuit to improve linearity for the most accurate sound amplification. This technology also stabilizes the amplifier output while driving the speakers for ultimate reliability.
The HDA-F60 features Alpine’s quick- connect power and speaker connectors for quick and safe installation. The one- sided terminal layout and top-panel sound controls give the user quick access to controls on the amplifier.
The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System.
Features
Hi-Res Audio Playback (192kHz/24Bit)
4-Channel Amplifier
High-Efficiency Digital Circuit Design
Alpine’s Dual Negative Feedback Control Circuit
High Bandwidth Amplifier
Alpine’s Premium Class D Circuit Design
Copper-plated chassis
Black circuit board
One-sided terminal layout
Top panel sound controls
Quick connect power and speaker terminals
Optional Remote bass knob compatible (requires RUX-KNOB.2 or RUX-H01, sold separately)
Specifications
Dimensions: 11.4375” x 7.5” x 2.125”
Power Rating: (14.4V, ≤1.0% THD+N)
100W x 4 @ 4Ω
150W x 4 @ 2Ω
Bridged: 300W x 2 @ 4Ω
THD+N: 0.02% (10W into 4ohm)
S/N Ratio: 87dB (1W into 4ohm)
Frequency response: 10-60kHz (-3dB)
Damping factor: 500
Selectable input level – HI/LO
Selectable 2/4ch input
Variable High pass / Low pass crossover
Auto-turn on with remote sensing
Alpine HDA-F60 Manual
Alpine HD-Series 5-Channel Class-D Full-Range Hi-Resolution Automotive-Grade Amplifier, 75-Watts x 4ch @ 4-Ohms + 500-Watt Mono @ 2-Ohms
Using expertise gleaned from over five decades of crafting premium car audio products and trickle-down engineering and design from the Ultra Hi-Res Alpine-F#1Status system technologies, the Alpine Status-System features exceptional tooling and rich build quality for the best possible sound reproduction. Each component was hand-picked from the highest-quality materials for the highest in-class audio performance, that when used as a complete system, can achieve 192kHz/24Bit playback.
Powering a Hi-Res sound system without contributing noise during playback requires efficiency and precision and the HDA-V90 was intentionally designed to provide impressive power output to the system while ensuring the purest audio performance. The amplifier’s wide dynamic range capability provides impressive output in a compact chassis that fits most vehicle applications.
The HDA-V90 features a high-efficiency digital circuit design that ensures ultra- low distortion levels for precise sound reproduction and superb sound quality. Intentional designs, like a copper-plated chassis and black circuit board, bring the signal-to-noise ratio up to 87dB and minimize noise and distortion during playback for complete music fidelity that’s true to the original source.
Featuring technology unique to Alpine, the amplifier features Alpine’s dual negative feedback control circuit to improve linearity for the most accurate sound amplification. This technology also stabilizes the amplifier output while driving the speakers and subwoofers for ultimate reliability.
The HDA-V90 features Alpine’s quick- connect power and speaker connectors for quick and safe installation. The one- sided terminal layout and top-panel sound controls give the user quick access to controls on the amplifier.
The Alpine Status System is sold separately and can be used to build a custom sound system. Three sets of true 4V preamp outputs are included to add additional amplifiers if more power is needed. For best results, install the complete Alpine Status system together as a full system to achieve the highest in-class audio performance only second to the Ultra High-Resolution AlpineF#1System.
Specifications
Dimensions: 11.4375” x 7.5” x 2.125”
Power Rating: (14.4V, ≤1.0% THD+N)
75W x 4 + 300W x 1 @ 4Ω
100W x 4 + 500W x 1 @ 2Ω
Bridged: 200W x 2 @ 4Ω (ch1/2, ch3/4 only)
THD+N: 0.02% (10W into 4ohm)
S/N Ratio: 87dB (1W into 4ohm)
Frequency response: 8-60kHz (-3dB)
Damping factor: 500 (ch1/2/3/4), 1000 (subwoofer)
Selectable input level – HI/LO
Selectable 2/4/6ch input
Variable High pass / Low pass crossover
Variable Subsonic filter (subwoofer)
Bass EQ (0 to +12dB, Variable)
Auto-turn on with remote sensing
Alpine HDA-V90 Manual
XDM-Series 8-Channel Class-D Marine-Grade Amplifier, 100-Watts x 8-Channels @ 2-Ohm or 75-Watts x 8-Channels @ 4-Ohm
The ultra-versatile XDM800/8 delivers eight channels of crystal-clear, full-range power and is capable of delivering a whopping 100-watts to each of its channels @ 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is JL's advanced NexD high-speed switching design, which permits full bandwidth Class-D operation with extremely low distortion and remarkable efficiency.
Suitable for car or boat installations, the XDM800/8 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
The XDM800/8 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter, and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all eight amplifier channels directly from the driver's seat or cockpit.
Here are a few examples of how the XDM800/8 can be used:
Eight-channel Satellite Amp: drive four pairs of speakers with 75W x 8
Big Four-Channel Satellite Amp: bridge to produce 200W x 4 @ 4Ω
Six-Channel System Amp: drive front and rear satellites with 75W x 4 @ 4Ω, plus two 4Ω subwoofers with 200W each
Staggered Six-Channel Satellite Amp: drive front speakers with 200W x 2 @ 4Ω, plus four 4Ω speakers with 75W each
Staggered Five-Channel Satellite Amp: drive three front speakers with 200W @ 4Ω + rear speakers with 75W x 2
Four-Channel System Amp: drive left and right speakers with 200W x 2 @ 4Ω, plus two 4Ω subwoofers with 200W each
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
75 W RMS x 8 @ 14.4V
@ 2 Ω
100 W RMS x 8 @ 14.4V
Bridged @ 4Ω
200 W RMS x 4 @ 14.4V
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
2 or 4 or All Channels
Channel Input Mode Switch
Yes (2/4/6/8 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
Height (H)
2.05 in / 52 mm
Width (W)
14.73 in / 374 mm
Depth (D)
7.09 in / 180 mm
JL Audio XDM800/8 Manual
XDM-Series Three-Channel Class-D Marine-Grade Amplifier, 75-Watts x Two-Channels @ 4-Ohm and 300-Watt Mono @ 2-Ohm
Small enough to fit in just about any tight space application, the XDM500/3 is the perfect amplifier for a simple audiophile-grade, subwoofer / satellite system. With its three channels of versatile output, you can drive a pair of quality component speaker systems with plenty of clean power, while also delivering a stout 300W to your subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's advanced NexD switching amplifier design.
Suitable for car or boat installations, the XDM500/3 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
The XDM500/3 includes a 12dB / octave high-pass filter for its main channels, plus a variable slope low-pass filter for its subwoofer channel. Both filters offer continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
Main Channels @ 4 Ω
75 W RMS x 2 @ 14.4V
Main Channels @ 2 Ω
100 W RMS x 2 @ 14.4V
Main Channels - Bridged @ 4Ω
200 W RMS x 1 @ 14.4V
Subwoofer Channel @ 4 Ω
180 W RMS x 1 @ 14.4V
Subwoofer Channel @ 3 Ω
240 W RMS x 1 @ 14.4V
Subwoofer Channel @ 2 Ω
300 W RMS x 1 @ 14.4V
Subwoofer Channel @ 1.5 Ω
N/A
Main Channels @ 4 Ω
60 W RMS x 2 @ 12.5V
Main Channels @ 2 Ω
90 W RMS x 2 @ 12.5V
Main Channels - Bridged @ 4Ω
180 W RMS x 1 @ 12.5V
Subwoofer Channel @ 4 Ω
180 W RMS x 1 @ 12.5V
Subwoofer Channel @ 3 Ω
240 W RMS x 1 @ 12.5V
Subwoofer Channel @ 2 Ω
300 W RMS x 1 @ 12.5V
Subwoofer Channel @ 1.5 Ω
N/A
Frequency Response (Main Channels)
12 Hz - 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
10 Hz - 1 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>120 / 50 Hz
Damping Factor @ 2 Ω
>60 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s): Channels 1 & 2 (front)
High-Pass only
Filter Slope(s): Channels 1 & 2 (front)
12 dB/octave
Filter Frequency Range: Channels 1 & 2 (front)
50 Hz - 500 Hz
Filter Mode(s): Channels 3 & 4 (rear)
N/A
Filter Slope(s): Channels 3 & 4 (rear)
N/A
Filter Frequency Range: Channels 3 & 4
N/A
Filter Mode(s): Subwoofer Channel
Low-Pass only
Filter Slope(s): Subwoofer Channel
12/24 dB/octave
Filter Frequency Range: Subwoofer Channel
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Infrasonic Filter: Subwoofer Channel
none
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
Sub Ch. or All Channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes (1&2/Sum/Sub)
Height (H)
2.05 in / 52 mm
Width (W)
8.52 in / 216 mm
Depth (D)
7.09 in / 180 mm
Net Weight
4.8 lb / 2.18 kg
JL Audio XDM500/3v2 Manual
XDM-Series Four-Channel Class-D Marine-Grade Amplifier, 100-Watts x Four-Channels @ 2-Ohm or 75-Watts x 4-Channels @ Four-Ohm
The ultra-compact XDM400/4 packs a serious full-range punch, generating a whopping 100-watts to each of its four channels into 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD high-speed switching design, which permits full bandwidth Class-D operation with extremely low distortion and remarkable efficiency.
Suitable for car or boat installations, the XDM400/4 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
Combine the XDM400/4 with our XDM600/1 monoblock to build a stunning 1000W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat or deck. Or, use the XDM400/4 by itself to power two satellites, plus a subwoofer.
The XDM400/4 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the rear channels directly from the driver's seat or cockpit.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
75 W RMS x 4 @ 14.4V
@ 2 Ω
100 W RMS x 4 @ 14.4V
Bridged @ 4Ω
200 W RMS x 2 @ 14.4V
@ 4 Ω
60 W RMS x 4 @ 12.5V
@ 2 Ω
90 W RMS x 4 @ 12.5V
Bridged @ 4Ω
180 W RMS x 2 @ 12.5V
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
2 or All channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Level Modes
2 or All channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes
JL Audio XDM400/4v2 Manual
XDM-Series Monoblock Class-D Marine-Grade Amplifier, 300-Watts @ 2-Ohm or 200-Watts @ 4-Ohm
This little monoblock powerhouse employs JL-Audio's high-speed NexD switching design to achieve unprecedented efficiency and amazing power output for its size. It is small enough to fit in most tight space applications, including small boats, pickups, motorcycles and UTV’s (in a weather-tight compartment).
Designed for car or boat installations, the XDM300/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
Targeted specifically for subwoofer applications, the XDM300/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
200 W RMS x 1 @ 14.4V
@ 3 Ω
250 W RMS x 1 @ 14.4V
@ 2 Ω
300 W RMS x 1 @ 14.4V
@ 1.5 Ω
N/A
@ 4 Ω
160 W RMS x 1 @ 12.5V
@ 3 Ω
210 W RMS x 1 @ 12.5V
@ 2 Ω
270 W RMS x 1 @ 12.5V
@ 1.5 Ω
N/A
Frequency Response
10 Hz - 1 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>100 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>120 / 50 Hz
Damping Factor @ 2 Ω
>60 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Infrasonic Filter
none
Bass Boost EQ
No
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
Height (H)
2.05 in / 52 mm
Width (W)
6.85 in / 174 mm
Depth (D)
7.09 in / 180 mm
Net Weight
3.8 lb / 1.72 kg
JL Audio XDM300/1 Manual
XDM-Series 2-Channel Class-D Marine-Grade Amplifier, 100-Watts x 2-Channels @ 2-Ohm or 75-Watts x 2-Channels @ 4-Ohm
The tiny XDM200/2 packs a serious full-range punch, delivering a staggering 100-watts per channel into 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is JL's advanced high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency.
Suitable for car or boat installations, the XDM200/2 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
The XDM200/2 includes a 12dB / octave filter which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or cockpit.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
75 W RMS x 2 @ 14.4V
@ 2 Ω
100 W RMS x 2 @ 14.4V
Bridged @ 4Ω
200 W RMS x 1 @ 14.4V
@ 4 Ω
60 W RMS x 2 @ 12.5V
@ 2 Ω
90 W RMS x 2 @ 12.5V
Bridged @ 4Ω
180 W RMS x 1 @ 12.5V
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
20 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Security Cover for Controls
Yes
Pass-Through Preamp Output
Buffered
Height (H)
2.05 in / 52 mm
Width (W)
6.85 in / 174 mm
Depth (D)
7.09 in / 180 mm
Net Weight
3.75 lb / 1.70 kg
JL Audio XDM200/2 Manual
XDM-Series Monoblock Class-D Marine-Grade Amplifier, 1000-Watts @ 2-Ohm or 600-Watts @ 4-Ohm
This monoblock subwoofer powerhouse employs JL-Audio's high-speed NexD switching technology to achieve unprecedented efficiency and amazing power output from a very compact chassis. The XDM1000/1 generates up to 1000W of continuous power into a 2-ohm load (14.4V, 1% THD), making it a great choice to drive higher power subwoofer systems.
Designed for car or boat installations, the XDM1000/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.
Intended specifically for subwoofer applications, the XDM1000/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500Hz and a defeatable infrasonic filter (30Hz, 24dB/oct.). With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair.
Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.
Specifications
@ 4 Ω
600 W RMS x 1 @ 14.4V
@ 3 Ω
800 W RMS x 1 @ 14.4V
@ 2 Ω
1000 W RMS x 1 @ 14.4V
@ 1.5 Ω
N/A
@ 4 Ω
500 W RMS x 1 @ 12.5 V
@ 3 Ω
650 W RMS x 1 @ 12.5 V
@ 2 Ω
800 W RMS x 1 @ 12.5 V
@ 1.5 Ω
N/A
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>83 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>53 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
200 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Infrasonic Filter
30 Hz, defeatable
Bass Boost EQ
No
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional HD-RLC or MHD-RLC (water-resistant)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
Height (H)
2.05 in / 52 mm
Width (W)
14.73 in / 374 mm
Depth (D)
7.09 in / 180 mm
JL Audio XDM1000/1v2 Manual
Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm
Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker.
The KEY500.1 delivers 300 watts RMS of power to your speakers at 2-ohms. Measuring less than eight inches long and only two inches high, the KEY500.1 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.
If the temperature reaches the threshold, the Kicker KEY500.1's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption!
Specifications
Power (watts/ch), 1 Ohm mono
500
Power (watts/ch), 2 Ohm mono
300
Power (watts/ch), 4 Ohm mono
150
Standard dimensions in.(H x W x L)
1-11/16 x 4-1/8 x 8-1/8
Metric dimensions cm(H x W x L)
4.3 x 9.2 x 20.7
Frequency Response (Hz):
10-160
Input Sensitivity:
high level: 1V-40V / low level: 125mV-5V
Signal-to-Noise Ratio:
>90dB, a-weighted, re: rated power
Selectable Electronic Crossover:
Variable Low Pass 40-160 Hz, Variable High Pass 10-40 Hz
What's in the Box:
1 - fuse holder1 - manual and installation hardware
Kicker 47KEY5001 Manual
Kicker Key-Series 50-Watt x 4-Channel Power-Pack Amplifier with Automatic DSP and Built-In EQ Processor
Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker.
The KEY200.4 delivers 200 watts RMS of power to your speakers. Measuring less than eight inches long and only two inches high, the KEY200.4 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.
If the temperature reaches the threshold, the Kicker KEY200.4's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption!
Specifications
Power (watts/ch), 4 Ohm stereo
50 x 4
Microphone/Kicker EQ button
included
Standard dimensions(H x W x L)
1-11/16 x 2-3/4 x 7-3/8
Metric dimensions(H x W x L)
4.3 x 7 x18.7
Frequency Response (Hz):
20-20k, +0/-1dB
Input Sensitivity:
high level 250mV-10V
Signal-to-Noise Ratio:
>90dB, a-weighted, re: rated power
Active Crossover:
24dB/octave, selective high pass or all pass @60,80, or 120Hz
What's in the Box:
1 - 4 channel power amplifier1 - microphone1 - microphone cable with switch1 - fuse holder1 - manual and installation hardware
Kicker 47KEY2004 Manual
JD-Series Monoblock Amplifier, 250-Watt @ 2-Ohm or 150-Watt @ 4-Ohm
Designed to produce a healthy 250 watts into 2 ohms (14.4V, 1% THD), the JD250/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD250/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD250/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you easily set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
150 W RMS x 1
@ 3 Ω
200 W RMS x 1
@ 2 Ω
250 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD250/1 Manual
MX-Series 75-Watts x 2-Channel Class-D Marine-Grade Amplifier + 400-Watt Subwoofer Out @ 2-Ohm
Engineered specifically for powersports applications, the 3-channel MX600/3 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 75W x 2 into 4 ohms (14.4V, 1% THD), the MX600/3 is the perfect solution for driving a pair of speakers and a subwoofer.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>92 / 50 Hz
Damping Factor @ 2 Ω
>43 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 580 mV - 14 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Main Channels @ 4 Ω
75 W RMS x 2
Main Channels @ 2 Ω
100 W RMS x 2
Main Channels - Bridged @ 4Ω
200 W RMS x 1
Subwoofer Channel @ 4 Ω
250 W RMS x 1
Subwoofer Channel @ 3 Ω
300 W RMS x 1
Subwoofer Channel @ 2 Ω
400 W RMS x 1
Subwoofer Channel @ 1.5 Ω
N/A
JL Audio MX600/3 Manual
MX-Series 4-Channel Marine-Grade Amplifier, 125-Watts x 4ch @ 2-Ohm or 70-Watts x 4ch @ 4-Ohm
Engineered specifically for powersports applications, the 4-channel MX500/4 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 70W x 4 into 4 ohms (14.4V, 1% THD), the MX500/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 250W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>70.5 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>92 / 50 Hz
Damping Factor @ 2 Ω
>43 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
70 W RMS x 4
@ 2 Ω
125 W RMS x 4
Bridged @ 4Ω
250 W RMS x 2
JL Audio MX500/4 Manual
JL-Audio MX-Series 500-Watt Monoblock Marine-Grade Power-Pack Style Amplifier @ 2-Ohm or 300W @ 4-Ohm
Engineered specifically for powersports applications, the MX500/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 500W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX500/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 12 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>97 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>70 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>115 / 50 Hz
Damping Factor @ 2 Ω
>54 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
300 W RMS x 1
@ 3 Ω
400 W RMS x 1
@ 2 Ω
500 W RMS x 1
@ 1.5 Ω
N/A
JL Audio MX500/1 Manual
Kicker CX-Series Four-Channel Amplifier, 60-Watts x 4-Channel at 4-Ohm or 65-Watts x 4-Channel at 4-Ohm
This CX-Series 4-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA3604t amplifier delivers as much as 90W into 4 audio channels.
Specifications
MODEL
CXA360.4
Power (watts/ch) 4 Ohm Stereo
65W x 4ch
Power (watts/ch) 2 Ohm Stereo
90W x 4ch
Power (watts/ch) 4 Ohm Mono
180W x 2ch
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)12-1/2, 31.7
Frequency Response (Hz):
10Hz-20kHz
Input Sensitivity:
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio:
95dB
Active Crossover:
HI, LO or OFF; Variable 50–200Hz @ 12dB/Octave
Subsonic Filter:
n/a
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker 46CXA3604t Manual
Mono Amplifier, 1800-Watts at 2-Ohm, 900-Watts at 4-Ohm
This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.
Efficient Class-D amplifier
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ™ 6dB variable bass boost for those additional low frequencies
24dB subsonic filter for protection from potentially damaging frequencies
FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
This Kicker 46CXA18001t amplifier delivers as much as 1,800W into one bass channel.
Specifications
MODEL
CXA1800.1
Power (watts/ch) 4 Ohm
900x1
Power (watts/ch) 2 Ohm
1800x1
Power (watts/ch) 1 Ohm
1800x1 +/-10%
CXRC Remote Bass Capable (sold sep.)
yes
Dimensions (in, cm)
(all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)14-3/8, 36.4
Frequency Response (Hz)
25-200Hz
Input Sensitivity
250mV-10V (Low Level)1V-40V (High Level)
Signal-to-Noise Ratio
95dB
Active Crossover
Variable Lo-pass 50Hz–200Hz, 12dB/octave
Subsonic Filter
25Hz @24dB/octave
KickEQ™ Boost
Variable 0-6dB @40Hz
Kicker CXA Mono Amplifier Manual
