At this present time our store location is open by appointment only.

50W x 4 @ 4Ω

Amplifiers with a Power Output Rating of 50-Watts x 4-Channels, 4-Ohm Final Impedance

Amplifiers with a Power Output Rating of 50-Watts x 4-Channels, 4-Ohm Final Impedance

RMS power: This rating of any amplifier is the continuous power rating that an amp is designed to output at a maximum continued volume rating. The RMS power specification is one of two numbers to go by when pairing your speakers with an amplifier, not the only 2 but a good starting point. As an example, a speaker driver with a 50-Watt, or 50W for short, RMS rating should be paired with a fifty-watt RMS amplifier. We usually recommend an amp to be over powered by 10% RMS so that the power-plant does not have to work at 100% capacity to get 100-percent efficiency from your speakers. This will keep your amplifier from overheating during long periods of continuous operation.

Ohms: Is the resistance rating of an amp and is the second most important when pairing drivers with amplifiers. A power-plant that is 50W @ 4-ohm might put out 100-Watts @ 2Ω. When purchasing an amplifier, the correct pairing of a speaker’s RMS wattage and Ohm ratings with an amp’s output power rating is absolutely essential.

2 products

  • Last One! JL Audio MX280/4 : 50W x 4ch Marine Amplifier @ 4Ω JL Audio MX280/4 : 50W x 4ch Marine Amplifier, side view.

    JL Audio MX280/4 : 50W x 4ch Marine Amplifier @ 4Ω

    1 Available for pickup

    MX-Series 4-Channel Class-D Marine-Grade Amplifier, 70-Watts x 4ch @ 2-Ohm or 50-Watts x 4ch @ 4-Ohm Engineered specifically for powersports applications, the 4-channel MX280/4 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. Generating a solid 50W x 4 into 4 ohms (14.4V, 1% THD), the MX280/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 140W x 2 into 4 ohms. Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 20 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >89.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >60 / 50 Hz Damping Factor @ 2 Ω >30 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 35 A (AFS, AGU or MaxiFuse™) @ 4 Ω 50 W RMS x 4 @ 2 Ω 70 W RMS x 4 Bridged @ 4Ω 140 W RMS x 2 JL Audio MX280/4 Manual

    1 Available for pickup


  • 50W x 4ch Amplifier with Built-In DSP : Kicker 47KEY200.4 50W x 4ch Amplifier with Built-In DSP : Kicker 47KEY200.4 top left side.

    Kicker 47KEY2004 : 50W x 4ch Amplifier with Built-In DSP

    Pre-Order Today!

    4-Channel Amplifier with Automatic DSP and Built-In EQ/Processor, 50-Watts RMS @ 4-Ohms x 4ch Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker. The KEY200.4 delivers 200 watts RMS of power to your speakers. Measuring less than eight inches long and only two inches high, the KEY200.4 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.  If the temperature reaches the threshold, the Kicker KEY200.4's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption! Specifications Power (watts/ch), 4 Ohm stereo 50 x 4 Microphone/Kicker EQ button included Standard dimensions(H x W x L) 1-11/16 x 2-3/4 x 7-3/8 Metric dimensions(H x W x L) 4.3 x 7 x18.7 Frequency Response (Hz): 20-20k, +0/-1dB Input Sensitivity: high level 250mV-10V Signal-to-Noise Ratio: >90dB, a-weighted, re: rated power Active Crossover: 24dB/octave, selective high pass or all pass @60,80, or 120Hz What's in the Box: 1 - 4 channel power amplifier1 - microphone1 - microphone cable with switch1 - fuse holder1 - manual and installation hardware Kicker 47KEY2004 Manual

    Pre-Order Today!



Forgot your password?

Don't have an account yet?
Create account