Mounting Depth

W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality. The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω/4Ω JL Audio 10W1v3 Manual

Read more less

MM-Series 420-Watt RMS 12-Inch Subwoofer Driver, 4-Ohm SVC Specifications Qty Included : 1 Driver Enclosure Type : Ultra-Marine Certified Driver Complement: (1) 12" (30.48 cm) d (Round) - Subwoofer Shape : Round Diameter : 11.1" (28.19 cm) Full-Range Mounting Depth - Top Mount : 4.65" (11.81 cm) Full-Range Mounting Depth - Bottom Mount : 5.2" (13.21 cm) Total Frequency Response : 26 Hz → 200 Hz Nominal Impedance : 4 ohms Sensitivity (1 watt @ 1 meter) : 87 dB Continuous Power Handling : 420W Peak Power Handling : 1260W Drivers Warranty : 1 years Polk Audio MM1 Subwoofer Manual

Read more less

W1-Series 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The 12" W1v3 automotive subwoofer driver by JL Audio is a lightweight 12-inch driver with excellent performance capabilities at a moderate 300-Watts. The design of the chassis allows an average mounting depth with no pole-vent on the back side of the magnet so the rear of the motor structure can be placed directly against an enclosure boundary. This 12" subwoofer can reproduce sub-bass with shocking extension and quality. The JL Audio 12W1v3-2 and 12W1v3-4 subwoofers are best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure.  General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω JL Audio 12W1v3 Manual

Read more less

10-Inch 300-Watt 2-Ohm or 4-Ohm Thin Subwoofer-Enclosure for Select 2018-2023 Jeep Wrangler-Unlimited, Passenger-Side Combining JL's advanced thin-line subwoofer technology with a form fitting enclosure design, these Stealthbox® systems deliver outstanding sub-bass performance in your 4-door Wrangler, without consuming excess cargo space. Constructed from 100% fiberglass, each Stealthbox® houses a 10TW1 thin-line subwoofer and mounts solidly above each rear wheel well. A matching trim panel and sturdy steel-mesh grille are included, so you can carry plenty of gear without worrying about damage. Separate driver and passenger side Stealthbox® models are available, each with 2 or 4 ohm drivers. The Hard Data: Contains one 10TW1 in a sealed enclosure with 300 watt power handling. Choose from 2 ohm or 4 ohm models, driver or passenger side. Each enclosure installs above one rear wheel well. Black steel mesh grille is included with each. If vehicle is factory-equipped with Premium Audio, passenger side Stealthbox® installation requires removal of OEM “subwoofer” and purchase of interior trim parts from Jeep®. Will not fit any "JK" Jeep® model or 2-Door "JL" models. Soft-top models: Stealthbox® installation does not interfere with normal top operation, except for the final position where the top mechanism is detached from the rails. Jeep Part #CFWLR-74-24 carpet needs to be ordered from jeep to remove the Factor Subwoofer. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-J-JL4DPAS/10TW1-2 Installation Manual

Read more less

W3-Series 13-Inch 600-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Single Voice Coil If you have the space, it makes a tremendous sense to maximize your subwoofer system's piston area to enhance efficiency (and output). It gets even better when the larger driver delivers additional power handling and excursion. For the preceding reasons, the 13W3v3 can be the best choice for those seeking high output with great sound quality at medium power levels. As with the smaller W3v3's, several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 13W3v3 to enhance linearity and reliability. The 13W3v3 2Ω or 4Ω model is best used with an amplifier powered in the 150W - 600W range and is optimized to operate in a moderate size 1.5 cu. ft. (42.5 l) sealed enclosure, or a 2.25 cu. ft. (63.7 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 600W Recommended Amplifier Power (RMS) 150 - 600W Nominal Impedance (Znom) 4Ω Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14.0 in / 356 mm Mounting Hole Diameter (B) 12.5625 in / 319 mm Bolt Hole Circle Diameter (C) 13.2 in / 335 mm Motor Outer Diameter (D) 5.79 in / 147 mm Mounting Depth (E) 7.63 in / 194 mm Driver Displacement 0.096 cu ft / 2.72 liters Net Weight 17.75 lb / 8.05 kg Free Air Resonance (Fs) 23.66 Hz Electrical “Q” (Qes) 0.465 Mechanical “Q” (Qms) 6.774 Total Speaker “Q” (Qts) 0.435 Equivalent Compliance (Vas) 4.793 cu ft / 135.74 L One-Way Linear Excursion (Xmax)* 0.610 in / 15.5 mm Reference Efficiency (no) 0.37% Efficiency (1 W / 1 m)** 87.90 dB SPL Effective Piston Area (Sd) 103.850 sq in / 0.0670 sq m DC Resistance (Re) 3.569 Ω JL Audio 13W3v3 Manual

Read more less

Single 13-Inch 600-Watt 4-Ohm Thin Subwoofer-Enclosure for Select 2007-2013 Toyota Tundra-CrewMax Pickups Toyota's largest truck offers amazing people space, but doesn't leave much for a traditional subwoofer enclosure. It's a good thing JL Didn't let conventional thinking get in the way of creating Stealthbox® solutions. Using the remarkable 13TW5v2 thin-line subwoofer, JL Audio have created a powerful Stealthbox® that can be installed behind the back seat of the big Tundra. One is enough for creating outstanding sub-bass with deep extension and solid impact, but for those looking for maximum performance, installing a pair of them will deliver up to 6dB more output. The Hard Data: Contains one 13TW5v2-4 subwoofer in a sealed enclosure. 600 watt power handling. Wired for 4 ohm mono. Installs behind the rear bench. One notch of seat travel is lost with installation and full-recline of the seat-back is only available when the seat is in its more forward positions. If the vehicle is equipped with the factory JBL® subwoofer, you must do one of the following to install the Stealthbox®: A) Permanently modify (cut) the factory trim panel.  B) Obtain a replacement “no-subwoofer” trim panel from Toyota Parts prior to installation. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-T-TUNDCMAX/13TW5v2 Installation Manual

Read more less

10-Inch 300-Watt 2-Ohm or 4-Ohm Subwoofer Enclosure for Select 2018-2023 Jeep Wrangler-Unlimited, Driver Side Combining JL's advanced thin-line subwoofer technology with a form fitting enclosure design, these Stealthbox® systems deliver outstanding sub-bass performance in your 4-door Wrangler, without consuming excess cargo space. Constructed from 100% fiberglass, each Stealthbox® houses a 10TW1 thin-line subwoofer and mounts solidly above each rear wheel well. A matching trim panel and sturdy steel-mesh grille are included, so you can carry plenty of gear without worrying about damage. Separate driver and passenger side Stealthbox® models are available, each with 2 or 4 ohm drivers. The Hard Data: Contains one 10TW1 in a sealed enclosure with 300 watt power handling. Choose from 2 ohm or 4 ohm models, driver or passenger side. Each enclosure installs above one rear wheel well. Black steel mesh grille is included with each. If vehicle is factory-equipped with Premium Audio, passenger side Stealthbox® installation requires removal of OEM “subwoofer” and purchase of interior trim parts from Jeep®. Will not fit any "JK" Jeep® model or 2-Door "JL" models. Soft-top models: Stealthbox® installation does not interfere with normal top operation, except for the final position where the top mechanism is detached from the rails. Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order. JL Audio SB-J-JL4DDRV/10TW1-2 Installation Manual

Read more less

8-Inch 200-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 8" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS84 and 44CWCD84 8-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 200W RMS of amplified power. Specifications Size (IN.,CM) 8, 20 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 200 Peak Power (watts, per ANSI/CTA-2031-A) 400 Sensitivity (dB 1w/1m) 85.6 Mounting Depth (in, cm) 3 7/8, 9.8 Mounting Diameter (in, cm) 7, 17.7 Min Sealed Box Vol (cu. ft, L) 0.5, 14.2 Max Sealed Box Vol (cu. ft, L) 1.2, 34 Min Vented Box Vol (cu. ft, L) 0.66, 18.7 Max Vented Box Vol (cu. ft, L) 1.2, 34 Kicker CompC Subwoofer Manual

Read more less

10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 10" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS104 and 44CWCD104 10-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 300W RMS of amplified power. Specifications Size (IN.,CM) 10, 25 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 500 Sensitivity (dB 1w/1m) 86.2 Frequency Response (Hz) 30-500 Mounting Depth (in, cm) 4 13/16, 12.2 Mounting Cutout (in, cm) 9 1/8, 23.1 Min Sealed Box Vol (cu. ft, L) 1.0, 28.3 Max Sealed Box Vol (cu. ft, L) 2.4, 68 Min Vented Box Vol (cu. ft, L) 1.25, 35.4 Max Vented Box Vol (cu. ft, L) 1.75, 49.6 Kicker CompC Subwoofer Manual

Read more less

15-Inch 600-Watt Subwoofer Driver, 4-Ohm SVC or 4-Ohm DVC This CompC 15" sub driver from Kicker has a thick stamped steel basket that holds an injection-molded polypropylene cone with stabilizing ribs in the surround. The 44CWCS154 and 44CWCD154 15-Inch subs are available in a 4Ω Single Voice or 4Ω Dual Voice coil design with spring loaded speaker terminals. These CompC drivers are rated for 600W RMS of amplified power. Specifications Size (IN.,CM) 15, 38 Impedance (OHMS) 4 SVC or 4 DVC Recommended Amplifier Power (watts RMS) 600 Peak Power (watts, per ANSI/CTA-2031-A) 1200 Sensitivity (dB 1w/1m) 90.3 Frequency Response (Hz) 25-500 Mounting Depth (in, cm) 7, 17.7 Mounting Cutout (in, cm) 13 3/4, 35 Min Sealed Box Vol (cu. ft, L) 2.25, 63.7 Max Sealed Box Vol (cu. ft, L) 5.0, 141.6 Min Vented Box Vol (cu. ft, L) 3.0, 85 Max Vented Box Vol (cu. ft, L) 4.0, 113.3 Kicker CompC Subwoofer Manual

Read more less

10-Inch 350-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The CompVT 10" subwoofer by Kicker is a thin slimline driver that pounds in a limited space. A special four-layer voice coil provides the ability to work with serious amounts of power without the bulk of a standard subwoofer. The Kicker 43CVT102 and 43CVT104 subs work best with a sealed or ported enclosure and 350 watts of recommended power. Specifications SIZE [in, cm]: 10, 25 IMPEDANCE [Ohms]: 2 or 4 SVC Recommended Amplifier Power (watts RMS) 350 Peak Power (watts, per ANSI/CTA-2031-A) 700 SENSITIVITY [dB 1w/1m]: 87.2 MOUNTING DEPTH [in, cm]: 4 1/4, 10.8 MOUNTING DIAMETER [in, cm]: 9 3/16, 23.3 MIN SEALED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX SEALED BOX VOL [cu. ft, L]: 3, 85 MIN VENTED BOX VOL [cu. ft, L]: 1.25, 35.4 MAX VENTED BOX VOL [cu. ft, L]: 1.75, 49.6 Kicker CompVT Subwoofer Manual

Read more less

Alpine 350-Watt Thin 10-Inch Subwoofer Driver, 2Ω or 4Ω Impedance The SWT 10” Truck Subwoofer has been engineered to offer more installation flexibility without sacrificing big output to build the ideal sound system for your truck. At 4-1/8” deep, these subs provide deep bass performance where it normally couldn’t fit in a truck. And the vented pole optimized for 4-1/8” deep box is the ideal enclosure size meaning great bass performance can fit just about anywhere in your truck. The FEA-Optimized Motor Structure together with Alpine's revolutionary High-Amplitude Multi Roll (HAMR) Suspension Design gives the new SWT Truck Subwoofers the highest X-max and SPL output in its category. The new SWT Truck Subwoofers deliver the best-in-class bass output, ultra-low distortion, and unparalleled sound quality. With a real world, measured 11mm of X-max, the SWT subwoofers perform like traditional models, yet fit in smaller spaces. 4 UNIQUE ALPINE TECHNOLOGIES Radial Vented VC Heat Sink & Airflow Management SystemActively manages voice coil temperatures by forcing air directly across the heat sink system. FEA Optimized Dual-Sided Machined CRC Motor StructureCreates a symmetrical magnetic field with evenly distributed flux density to greatly reduce distortion, while further improving power handling and output. FEA Optimized Injection Molded TPE Spider with Pass-Through Gap DesignProvides the mechanical clearance needed for over 50mm of peak-to-peak excursion, unleashing massive output potential from a small package FEA Optimized HAMR SurroundThe High-Amplitude Multi Roll Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene ®, the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions. Specifications 350W RMS, 1000W Peak Power Handling Frequency Response: 30Hz-200Hz Mounting Depth 4-3/16" 2Ω or 4Ω Voice Coil

Read more less

W0-Series 12-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The 12" W0v3 subwoofer driver by JL Audio delivers excellent efficiency, excursion capability and linearity. This 12" subwoofer comes with a price point under $150.00 while supporting a beefy 2 in. diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. The JL Audio 12W0v3-4 sub is best used with amplifier power in the 75W - 300W range and is optimized to operate in a moderately sized 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 4Ω JL Audio 12W0v3 Manual

Read more less

W0-Series 10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC The JL Audio 10" W0v3 subwoofer driver is a rugged performer with excellent excursion capability and linearity while sporting a 2 inch diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability. This 10 inch subwoofer is best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 0.65 cu. ft. (18.4 l) sealed enclosure, or a 1.125 cu. ft. (31.9 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 300W RMS Recommended Amplifier Power (RMS) 75W - 300W RMS Nominal Impedance (Znom) 4Ω JL Audio 10W0v3 Manual

Read more less

W1-Series 8-Inch 150-Watt Subwoofer Driver, 4-Ohm SVC The 8W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (3.86 in. / 98 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 8-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 8W1v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a compact 0.350 cu. ft. (9.90 l) sealed enclosure. General Specifications Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω JL Audio 8W1v3 Manual

Read more less

TW1-Series 12-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The 12" TW1 thin subwoofer driver by JL Audio has a shallow mounting depth while maintaining excellent excursion capability in a thin mounty chassis design to fit into an enclosure no bigger than (0.65 cu.ft. / 18.4 liters). This 12TW1 subwoofer is capable of operating in extremely tight spaces including under-seat installations in trucks and other automotive applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology utilizes a "concentric tube" structure built into the injection-molded cone body supporting the voice coil and spider. This patented design places the large motor structure further forward in the speaker than conventional thin subwoofer designs. The JL Audio 12TW1 sub also features a chassis design that minimizes the top clearance required for the linear excursion limits of the subwoofer driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. The 12TW1 requires only 0.87 inches (22 mm) of frontal clearance with or without the subwoofer grille installed. The JL Audio 12" 12TW1-2 and 12TW1-4 subwoofer drivers are optimized for an enclosure much smaller than any other JL Audio twelve-inch subwoofer driver, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling () 300W RMS Recommended Amplifier Power (RMS) 75W - 300W RMS Nominal Impedance (Znom) 2Ω JL Audio 12TW1 Manual

Read more less

10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10" TW1 automotive thin subwoofer driver chassis offers a shallow mounting depth and excellent linear excursion capability while requiring a small enclosure (0.35 cu.ft. / 10 liters). The cast alloy frame design on the JL 10TW1 is capable of operating in very tight spaces like under-seat installations in trucks. The 10TW1 design uses a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 thin subwoofer also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Although the JL Audio 10TW1-2  and 10TW1-4 thin subwoofer drivers are optimized for an enclosure much smaller than most other 10 inch subwoofer drivers, they never sound like a big woofer struggling in a tiny box...instead, the 10TW1's delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling 300W RMS Recommended Amplifier Power 75W - 300W RMS Nominal Impedance 2Ω/4Ω JL Audio 10TW1 Manual

Read more less

W3-Series 12-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm Single Voice Coil This 12-inch W3v3 subwoofer driver by JL Audio delivers world-class sound quality in a 500W RMS power package.  The JL Audio 12W3v3-2 and 12W3v3-4 automotive subs are best used with an amplifier in the 150-Watt - 500-Watt RMS range and are optimized to operate in a compact 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. General Specifications Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 2 Ω JL Audio 12W3v3 Manual

Read more less

W3-Series 10-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 10W3v3 subwoofer driver has excellent power handling, reasonable enclosure requirements, and a long excursion for its chassis to deliver excellent bass reproduction in 500W RMS power applications. JL Audio technologies and proprietary assembly designs in the 10W3v3-2 and 10W3v3-4 subwoofers enhance linearity and reliable performance results. The JL Audio 10W3v3 is best used with an amplifier in the 150W - 500W RMS range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure. General Specifications Continuous Power Handling 500W RMS Recommended Amplifier Power 150- 500W RMS Nominal Impedance 2Ω JL Audio 10W3v3 Manual

Read more less

W3-Series 8-Inch 250-Watt Subwoofer Driver, 4-Ohm SVC If you need an 8-inch subwoofer that can create outstanding bass in extremely small enclosures, the 8W3v3 will do the job and surprise you with its power and accuracy. It employs the same technologies as its larger diameter brethren to deliver a whopping 0.375 in. (10 mm) of controlled, one-way, linear excursion. The 8W3v3-4 is best used with amplifier power in the 75W - 250W range and is optimized to operate in a tiny 0.30 cu. ft. (8.5 l) sealed enclosure, or a 0.35 cu. ft. ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 250 W Recommended Amplifier Power (RMS) 75- 250 W Nominal Impedance (Znom) 4 Ω JL Audio 8W3v3 Manual

Read more less

W6-Series 6.5-Inch 150-Watt Subwoofer Driver, 4-Ohm If you need a small-format subwoofer that really delivers in extremely small enclosures, this is where your search ends. The 6W3v3 is a true subwoofer, through-and-through. It employs the same technologies as its larger diameter brethren to deliver a whopping 0.35 in. (8.9 mm) one-way linear excursion. The 6W3v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a tiny 0.15 cu. ft. (4.2 l) sealed enclosure, or a 0.25 cu. ft. ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω JL Audio 6W3v3 Manual

Read more less

TW5-Series 13.5-Inch 600-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 13.5" TW5v2 thin subwoofer driver uses a chassis with a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the subwoofer chassis than with conventional thin sub designs, while allowing excellent linear excursion capability and mechanical stability. The 13TW5v2 improves upon the original 13-Inch TW5 driver with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is available in single 2-ohm and single 4-ohm voice coil configurations. In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 12-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer. The JL Audio 13TW5v2-2 and the 13TW5v2-4 thin subwoofers are best used with amplifier power in the 250-Watt - 600-Watt range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure. Never has such high-quality subwoofers-bass been possible in the most challenging thin installation applications. General Specifications Continuous Power Handling 600W RMS Recommended Amplifier Power 250W - 600W RMS Nominal Impedance 2Ω JL Audio 13TW5v2 Manual

Read more less