At this present time our store location is open by appointment only.

2ch

Automotive Amplifiers and Electronics with a Two-Channel Audio Output

Automotive Amplifiers and Electronics with a Two-Channel Audio Output

3 products

  • JL Audio XDM200/2 : 2ch Marine Amplifier, 100W/75W x 2ch @ 2Ω/4Ω. JL Audio XDM200/2 : 2ch Marine Amplifier, top side.

    JL Audio XDM200/2 : 2ch Marine Amplifier, 100W/75W x 2ch @ 2Ω/4Ω

    Pre-Order Today!

    XDM-Series 2-Channel Class-D Marine-Grade Amplifier, 100-Watts x 2-Channels @ 2-Ohm or 75-Watts x 2-Channels @ 4-Ohm The tiny XDM200/2 packs a serious full-range punch, delivering a staggering 100-watts per channel into 2-ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is JL's advanced high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM200/2 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM200/2 includes a 12dB / octave filter which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 75 W RMS x 2 @ 14.4V @ 2 Ω 100 W RMS x 2 @ 14.4V Bridged @ 4Ω 200 W RMS x 1 @ 14.4V @ 4 Ω 60 W RMS x 2 @ 12.5V @ 2 Ω 90 W RMS x 2 @ 12.5V Bridged @ 4Ω 180 W RMS x 1 @ 12.5V Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS  Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 20 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Security Cover for Controls Yes Pass-Through Preamp Output Buffered Height (H) 2.05 in / 52 mm Width (W) 6.85 in / 174 mm Depth (D) 7.09 in / 180 mm Net Weight 3.75 lb / 1.70 kg JL Audio XDM200/2 Manual

    Pre-Order Today!

    $499.99

  • 600W x 2ch Marine Amplifier @ 2Ω, or 300W x 2 @ 4Ω : Kicker 44KXMA12002 600W x 2ch Marine Amplifier @ 2Ω, or 300W x 2 @ 4Ω : Kicker 44KXMA12002, top side.

    Kicker 48KXMA12002 : 600W x 2ch Marine Amplifier @ 2Ω, or 300W x 2 @ 4Ω

    Pre-Order Today!

    2-Channel Marine Amplifier, 600-Watt x 2ch @ 2-Ohm, or 300-Watt x 2 @ 4-Ohm This KXM 2ch marine amplifier uses Class D power technology, KickEQ+™ for 18dB of amplified variable bass boost, and a powerful 24dB crossover and subsonic filter to give you onboard acoustic control to quickly tune your setup. A wireless remote controlled bass knob is also included for tuning your subs on the fly. This Kicker KXM 2 channel weatherproof amplifier can be used to power 600W into a 2Ω load or 300W into a 4Ω load. Specifications RMS Power [Watts] @ 14.4V, 4Ω stereo, ≤ 1% THD+N : 300 x 2@ 14.4V, 2Ω stereo, ≤ 1% THD+N : 600 x 2 Length [in, cm] 11 3∕16 , 28.4 Height [in, cm] 2 ⅛, 5.5 Width [in, cm] 8 5⁄16 , 21 Frequency Response ± 1dB 10Hz–20kHz Signal-to-Noise Ratio 95dB Input Sensitivity 250mV–10V Selectable Electronic Crossover OffVariable HP, 10-500HzVariable LP, 40-500Hz; 400Hz–5,000Hz with 10X Switch (BP capable)Slope: 24dB/octave KickEQ™ Bass Boost 0-18dB @ 40Hz CEA Power 300 x 2 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts) CEA Signal-to-Noise Ratio -75dB CEA-2006B (ref: 1W, A-weighted) Kicker KXMA Amplifier Manual

    Pre-Order Today!

    $649.99

  • Kicker 48KXMA4002 : 200W x 2ch Marine Amplifier @ 2Ω, or 100W x 2 @ 4Ω Kicker 48KXMA4002 : 200W x 2ch Marine Amplifier @ 2Ω, or 100W x 2 @ 4Ω

    Kicker 48KXMA4002 : 200W x 2ch Marine Amplifier @ 2Ω, or 100W x 2 @ 4Ω

    Pre-Order Today!

    2-Channel Marine Amplifier, 200-Watt x 2ch @ 2-Ohm, or 100-Watt x 2 @ 4-Ohm This KXM 2ch marine amplifier uses Class D power technology, KickEQ+™ for 18dB of amplified variable bass boost, and a powerful 24dB crossover and subsonic filter to give you onboard acoustic control to quickly tune your setup. A wireless remote controlled bass knob is also included for tuning your subs on the fly. This Kicker KXM 2 channel weatherproof amplifier can be used to power 200W into a 2Ω load or 100W into a 4Ω load. Specifications RMS Power [Watts] @ 14.4V, 4Ω stereo, ≤ 1% THD+N : 100 x 2@ 14.4V, 2Ω stereo, ≤ 1% THD+N : 200 x 2@ 14.4V, 4Ω bridged mono, ≤ 1% THD+N: 400 x 1 Length [in, cm] 9 9∕16 , 24.4 Height [in, cm] 2 ⅛, 5.5 Width [in, cm] 8 5⁄16 , 21 Frequency Response ± 1dB 10Hz–20kHz Signal-to-Noise Ratio [dB] 95 Input Sensitivity 250mV-10V Selectable Electronic Crossover OffVariable HP, 10-500HzVariable LP, 40-500Hz; 400Hz–5,000Hz with 10X Switch (BP capable)Slope: 24dB/octave KickEQ+™ Bass Boost 0-18dB @ 40Hz CEA Power 100 x 2 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts) CEA Signal-to-Noise Ratio -75dB CEA-2006B (ref: 1W, A-weighted) Kicker KXMA Amplifier Manual

    Pre-Order Today!

    $379.99

Login

Forgot your password?

Don't have an account yet?
Create account