Alpine 350-Watt Loaded 10-Inch Subwoofer-Enclosure for 2007-2018 Jeep-Wrangler JK-Unlimited, 2Ω Final Impedance
When you have a Wrangler, you don’t have extra space to spare. Alpine engineered the SBV-10-WRA to conveniently fit under the front passenger’s seat making efficient use of space. The SBV-10-WRA is a custom-shaped enclosure that fits snugly under the seat frame, so no mounting hardware is required. (NOTE: designed for fitment in Jeeps with the factory carpet. Fitment is not guaranteed with aftermarket or removed carpet)
Enjoy impactful bass, with your Wrangler’s top on or off. The SBV-10-WRA loads the lower frequency sound into the passenger’s foot well to deliver quality sound and maximized bass extension at all times, so your music continues even when the asphalt ends.
Specifications
10” Pre-loaded Sealed Custom-fit Enclosure
Weather Resistant (IP66 rating)
Power Handling: 350WRMS/1050W Peak
Nominal Impedance 2Ω
Frequency Response: 45-200Hz
OEM-grade Molex 2-pin connector w/pigtail wire harness
Alpine SBV-10-WRA Manual
Alpine 350-Watt Thin 10-Inch Subwoofer Driver, 2Ω or 4Ω Impedance
The SWT 10” Truck Subwoofer has been engineered to offer more installation flexibility without sacrificing big output to build the ideal sound system for your truck. At 4-1/8” deep, these subs provide deep bass performance where it normally couldn’t fit in a truck. And the vented pole optimized for 4-1/8” deep box is the ideal enclosure size meaning great bass performance can fit just about anywhere in your truck.
The FEA-Optimized Motor Structure together with Alpine's revolutionary High-Amplitude Multi Roll (HAMR) Suspension Design gives the new SWT Truck Subwoofers the highest X-max and SPL output in its category.
The new SWT Truck Subwoofers deliver the best-in-class bass output, ultra-low distortion, and unparalleled sound quality. With a real world, measured 11mm of X-max, the SWT subwoofers perform like traditional models, yet fit in smaller spaces.
4 UNIQUE ALPINE TECHNOLOGIES
Radial Vented VC Heat Sink & Airflow Management SystemActively manages voice coil temperatures by forcing air directly across the heat sink system.
FEA Optimized Dual-Sided Machined CRC Motor StructureCreates a symmetrical magnetic field with evenly distributed flux density to greatly reduce distortion, while further improving power handling and output.
FEA Optimized Injection Molded TPE Spider with Pass-Through Gap DesignProvides the mechanical clearance needed for over 50mm of peak-to-peak excursion, unleashing massive output potential from a small package
FEA Optimized HAMR SurroundThe High-Amplitude Multi Roll Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene ®, the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions.
Specifications
350W RMS, 1000W Peak Power Handling
Frequency Response: 30Hz-200Hz
Mounting Depth 4-3/16"
2Ω or 4Ω Voice Coil
10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC
The JL Audio 10" TW1 automotive thin subwoofer driver chassis offers a shallow mounting depth and excellent linear excursion capability while requiring a small enclosure (0.35 cu.ft. / 10 liters). The cast alloy frame design on the JL 10TW1 is capable of operating in very tight spaces like under-seat installations in trucks.
The 10TW1 design uses a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs.
The 10TW1 thin subwoofer also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth.
Although the JL Audio 10TW1-2 and 10TW1-4 thin subwoofer drivers are optimized for an enclosure much smaller than most other 10 inch subwoofer drivers, they never sound like a big woofer struggling in a tiny box...instead, the 10TW1's delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system.
Very shallow mounting depth (4.36 in / 111 mm)
No pole vent: permits mounting close to rear wall of enclosure
Extremely small sealed enclosure volume requirements
Long linear excursion capability (0.40 in / 10 mm, one-way)
DMA-optimized motor design
Patented "concentric tube" architecture
Patented "floating cone attach method" technology
Cast alloy frame with flat edges for tight driver grouping
Injection molded, mica-filled polypropylene cone
Rubber surround
Steel mesh grille included with each driver
Precision-built in USA at JL Audio’s Miramar, Florida factory with global components
General Specifications
Continuous Power Handling
300W RMS
Recommended Amplifier Power
75W - 300W RMS
Nominal Impedance
2Ω/4Ω
JL Audio 10TW1 Manual
TW3-Series 10-Inch 400-Watt Automotive Subwoofer Driver, 4Ω or 8Ω DVC
The 10" TW3 thin subwoofer driver by JL Audio delivers a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of greater excursion than JL's W3v3 subwoofers!
JL Audio’s patented thin-line woofer technology compresses the architecture of the 10TW3 using a “concentric tube” structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of the large motor structure further forward in the speaker than with conventional 10-Inch thin subwoofer designs.
The 10TW3-D4 and 10TW3-D8 subwoofers are optimized for small enclosures and offer JL's tab-ear mounting design to maximize cone area within their mounting footprints.
Very shallow mounting depth (3.25 / 3.50 Inches)
No pole vent: permits mounting close to rear wall of enclosure.
Very small sealed enclosure volume requirements
Very long linear excursion capability (0.60 In / 15.2 mm, one-way)
DMA-optimized motor designs
“concentric tube” architecture
Patented “floating cone attach method” technology
Cast alloy frame
Injection molded, mica-filled polypropylene cone
Rubber surround
Aluminum-alloy dust cap and rear cap with JL Audio logo
Precision-built in USA at JL Audio’s Miramar, Florida factory with global components
General Specifications
Continuous Power Handling
400W RMS
Recommended Amplifier Power
200W - 400W RMS
Nominal Impedance
Dual 4Ω/8Ω
JL Audio 10TW3 Manual
W0-Series 10-Inch 300-Watt Subwoofer Driver, 4-Ohm SVC
The JL Audio 10" W0v3 subwoofer driver is a rugged performer with excellent excursion capability and linearity while sporting a 2 inch diameter voice coil and JL's patented Elevated Frame Cooling design for enhanced power handling and reliability.
This 10 inch subwoofer is best used with an amplifier in the 75W - 300W range and is optimized to operate in a compact 0.65 cu. ft. (18.4 l) sealed enclosure, or a 1.125 cu. ft. (31.9 l) ported enclosure.
General Specifications
Continuous Power Handling (RMS)
300W RMS
Recommended Amplifier Power (RMS)
75W - 300W RMS
Nominal Impedance (Znom)
4Ω
JL Audio 10W0v3 Manual
W1-Series 10-Inch 300-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC
The JL Audio 10" W1v3 subwoofer driver is a very suitable option when space is limited with smaller amplifiers. It features a low mounting depth of 4.6 inches and a compact motor structure that allows it to comfortably fit in tight mounting locations. There is no pole vent on the rear of the subwoofer which allows the motor structure to be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow the 10W1v3 to reproduce sub-bass with shocking extension and quality.
The JL Audio 10W1v3 is best used with an amplifier in the 75W - 300W RMS range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure.
General Specifications
Continuous Power Handling
300W RMS
Recommended Amplifier Power
75W - 300W RMS
Nominal Impedance
2Ω/4Ω
JL Audio 10W1v3 Manual
W3-Series 10-Inch 500-Watt Subwoofer Driver, 2-Ohm or 4-Ohm SVC
The JL Audio 10W3v3 subwoofer driver has excellent power handling, reasonable enclosure requirements, and a long excursion for its chassis to deliver excellent bass reproduction in 500W RMS power applications. JL Audio technologies and proprietary assembly designs in the 10W3v3-2 and 10W3v3-4 subwoofers enhance linearity and reliable performance results.
The JL Audio 10W3v3 is best used with an amplifier in the 150W - 500W RMS range and is optimized to operate in a compact 0.625 cu. ft. (17.7 l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.
General Specifications
Continuous Power Handling
500W RMS
Recommended Amplifier Power
150- 500W RMS
Nominal Impedance
2Ω
JL Audio 10W3v3 Manual
W6-Series 10-Inch 600-Watt Subwoofer Driver, 4-Ohm DVC
The 10W6v3 subwoofer driver offers several technologies similar to JL Audio's W7AE top line of subwoofers to provide powerful advantages in motor linearity and suspension behavior. This 10" automotive sub has a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance.
This 10" W6v3 driver is best used with an amplifier in the 200W - 600W RMS range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure.
The JL Audio 10W6V3-D4 subwoofer driver comes with Dual 4Ω voice coils that allow the 10W6v3 to be installed in a 2Ω or 8Ω configuration.
General Specifications
Continuous Power Handling
600W RMS
Recommended Amplifier Power
200 - 600W RMS
Nominal Impedance
Dual 4Ω
JL Audio 10W6v3 Manual
W7-Series 10-Inch 750-Watt Subwoofer Driver, 3-Ohm SVC
The audiophile 10W7AE subwoofer driver delivers amazing excursion capability while maintaining undeniable tracking accuracy under power in the low end sound spectrum.
This 10" W7AE sub is best used with an amplifier in the 300W - 750W RMS range and is optimized to operate in a 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.5 cu. ft. (42.5 l) ported enclosure.
The JL Audio 10W7AE-3 Anniversary Edition subwoofer driver is the 10th Anniversary of the launch of the JL W7 subwoofers. They are identical to the original W7's drivers but they are distinguished by the following cosmetic differences:
Satin-Black Powdercoated Baskets
Bright Anodized Surround Clamp Ring
Anniversary Edition Cone Badge
Anniversary Edition Terminal Label
General Specifications
Continuous Power Handling
750W RMS
Recommended Amplifier Power
300W - 750W RMS
Nominal Impedance
3Ω
JL Audio 10W7AE Manual
TW1-Series 400-Watt Amplified 10-Inch Ported Subwoofer System
With MicroSub+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this incredible subwoofer system utilizes JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency.
Key to the enclosure’s performance is its efficient slot-ported design and precise tuning of its 10TW1 subwoofer driver. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port.
Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space. As with all MicroSub™ systems, these amplified versions produce the kind of output and extension normally associated with much larger systems.
Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage.
Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω
General Specifications
Continuous Power Handling (RMS)
Built-in amplifier 400 W @ 0.25 Ω
System Nominal Impedance
0.25 Ω
Input Voltage Range @ RCA Inputs
70 mV - 1.40 V RMS
Input Voltage Range @ High-Level Inputs
280 mV - 5.4 V RMS
Recommended Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (ATO or ATC)
Enclosure Type
Slot-ported, Low-profile
Finish
Black carpet
Grille Included
Black Steel Mesh
JL Audio MicroSub+/PowerWedge+ Manual
TW1-Series 400-Watt Amplified 10-Inch Subwoofer System
In PowerWedge+™ systems, the power is built right into the subwoofer system. Housing a proprietary Class D amplifier, this subwoofer system employs JL's exclusive DCD™ amplifier technology to extract maximum output from its specially engineered, ultra low-impedance TW1 driver. By combining direct power conversion with an ultra-high current output section, DCD™ amplifiers are free of conventional switching power supplies, enabling them to generate remarkable power with unprecedented efficiency.
Harnessing the performance and insanely small box requirements of the TW1 subwoofer driver, this subwoofer system is designed to deliver amazing sub-bass from an enclosure that is only 5 inches (127 mm) deep. Its low-profile enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW1 driver and has been fine-tuned through extensive real-world listening.
Integration to OEM and aftermarket head units is a snap thanks to a variety of input options and automatic turn-on capability (via signal sensing or DC offset sensing). Also included is a variable frequency low-pass filter (50-200 Hz), along with output polarity control switch. Adding an optional RBC-1 remote level control (sold separately) lets you control subwoofer levels directly from the driver’s seat. A quick-disconnect power connector makes it easy to remove the subwoofer when you need the extra space.
Note: DCD™ amplified systems use very specific components. Never use a DCD™ amplifier or its companion subwoofer(s) with incompatible, non-DCD™ products. Doing so will void the warranty and may cause severe damage.
Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Amplifier power: Built-in DCD™ Class D amplifier (400 W @ 0.25 Ω)Nominal Impedance: 0.25 Ω
Enclosure and Subwoofer Built in USA with global components
General Specifications
Continuous Power Handling (RMS)
Built-in amplifier 400 W @ 0.25 Ω
System Nominal Impedance
0.25 Ω
Input Voltage Range @ RCA Inputs
70 mV - 1.40 V RMS
Input Voltage Range @ High-Level Inputs
280 mV - 5.4 V RMS
Recommended Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (ATO or ATC)
Enclosure Type
Sealed
Finish
Black carpet
Grille Included
Black Steel Mesh
JL Audio MicroSub+/PowerWedge+ Manual
ProWedge-Series 10-Inch 750-Watt Enclosed Subwoofer System, 3Ω Sealed Enclosure
For those who seek the ultimate in compact-enclosure sub-bass fidelity, we offer this sealed ProWedge™ system, in which the superb performance capabilities of the W7AE subwoofer driver are harnessed within a compact, sealed enclosure. This system has it all: extension, impact, detail and smooth response... at any listening level.
This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10W7AE-3 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
The angled-back design saves precious cargo space by allowing the enclosure to fit tightly against the back of a vehicle's rear seat.
Finish: Black, high-grade automotive carpet, with gloss-black laminated decorative front baffle trim. Three solid aluminum bars provide stylish and rugged woofer protection.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 300 - 750WNominal Impedance: 3 Ω
General Specifications
Continuous Power Handling (RMS)
750 W
System Nominal Impedance
3 Ω
Enclosure Type
Sealed, rear-firing design
Finish
Black carpet / laminate
Grille Included
Aluminum Bar Grille
Physical Specifications
External Width (W)
17.75 in / 451 mm
External Height (H)
14.625 in / 371 mm
External Depth (D1)
16.625 in / 422 mm
External Top Surface Depth (D2)
11.50 in / 292 mm
Net Weight
61.2 lb / 27.77 kg
JL Audio CLS110RG-W7AE Brochure
BassWedge-Series 10-Inch 300-Watt Enclosed Subwoofer System, 4Ω Ported Enclosure
This powerful slot-ported BassWedge™ subwoofer system delivers awesome output at an unsurpassed value.
The slot-port runs along the bottom of the enclosure and fires on the same plane as the woofer to produce excellent extension and response smoothness. The port mouth is flared to minimize air-flow noises.
The ultra-versatile BassWedge™ shape has extended sides so that it can be placed with the woofer firing out or straight down, off the floor of the vehicle. The shape works equally well in forward or rear-firing installations. This gives you plenty of options for tweaking the loading of the enclosure into your vehicle.
This subwoofer system is shipped wired, loaded and ready to connect via a push-button terminal.
Finish: Dark gray, high-grade automotive carpet with "JL AUDIO" embroidery on the top edge and "Slot-Ported BassWedge™" embroidered on the port mouth.
Construction: MDF
Recommended amplifier power: 75 - 300WNominal Impedance: 4 Ω
General Specifications
Continuous Power Handling (RMS)
300 W
System Nominal Impedance
4 Ω
Enclosure Type
Slot-ported
Finish
Gray carpet
Grille Included
No
Physical Specifications
External Width (W)
15.51 in / 394 mm
External Height (H)
13.77 in / 350 mm
External Depth (D1)
17.38 in / 441 mm
External Top Surface Depth (D2)
14 in / 356 mm
Net Weight
29 lb / 13.15 kg
JL Audio CP110-W0v3 Brochure
MicroSub-Series 10-Inch 300-Watt Enclosed Subwoofer System, 2Ω Ported Enclosure
This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 10TW1 subwoofer driver into an efficient slot-ported design.
Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 75 - 300WNominal Impedance: 2 Ω
General Specifications
Continuous Power Handling (RMS)
300 W
System Nominal Impedance
2 Ω
Enclosure Type
Slot-ported, Low-profile
Finish
Black carpet
Grille Included
Black Steel Mesh
Physical Specifications
External Width (W)
20.875 in / 530 mm
External Height (H)
13.25 in / 337 mm
External Depth (D1)
6.375 in / 162 mm
Net Weight
25.70 lb / 11.66 kg
JL Audio CP110LG-TW1-2 Brochure
BassWedge-Series Dual 10-Inch 600-Watt Enclosed Subwoofer System, 2Ω Ported Enclosure
This powerful slot-ported BassWedge™ subwoofer system delivers awesome output at an unsurpassed value.
The slot-port runs along the bottom of the enclosure and fires on the same plane as the woofers to produce excellent extension and response smoothness. The port mouth is flared to minimize air-flow noises.
The ultra-versatile BassWedge™ shape has extended sides so that it can be placed with the woofers firing out or straight down, off the floor of the vehicle. The shape works equally well in forward or rear-firing installations. This gives you plenty of options for tweaking the loading of the enclosure into your vehicle.
This subwoofer system is shipped wired, loaded and ready to connect via a push-button terminal.
Finish: Dark gray, high-grade automotive carpet with "JL AUDIO" embroidery on the top edge and "Slot-Ported BassWedge™" embroidered on the port mouth.
Construction: MDF
Recommended amplifier power: 150 - 600WNominal Impedance: 2 Ω
General Specifications
Continuous Power Handling (RMS)
600 W
System Nominal Impedance
2 Ω
Enclosure Type
Slot-ported
Finish
Gray carpet
Grille Included
No
Physical Specifications
External Width (W)
29.61 in / 752 mm
External Height (H)
13.77 in / 350 mm
External Depth (D1)
17.38 in / 441 mm
External Top Surface Depth (D2)
14 in / 356 mm
Net Weight
50.7 lb / 23 kg
JL Audio CP210-W0v3 Brochure
PowerWedge-Series 10-Inch 400-Watt Enclosed Subwoofer System, 2Ω Sealed Enclosure
In this low-profile PowerWedge™ subwoofer system, JL harnesses the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 4.5 in. (114 mm) deep.
This low-profile enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3-D4 and has been fine-tuned through extensive real-world listening.
The PowerWedge™ subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω
General Specifications
Continuous Power Handling (RMS)
400 W
System Nominal Impedance
2 Ω
Enclosure Type
Sealed
Finish
Black carpet
Grille Included
Black Steel Mesh
Physical Specifications
External Width (W)
20.75 in / 527 mm
External Height (H)
14 in / 357 mm
External Depth (D1)
4.5 in / 114 mm
Net Weight
21.2 lb / 9.6 kg
JL Audio CS110LG-TW3 Brochure
PowerWedge-Series 10-Inch 400-Watt Enclosed Subwoofer System, 2Ω Sealed Enclosure
In this sealed Truck PowerWedge™ subwoofer system, JL harnesses the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top.
This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω
General Specifications
Continuous Power Handling (RMS)
400 W
System Nominal Impedance
2 Ω
Enclosure Type
Sealed, truck enclosure
Finish
Black carpet
Grille Included
Black Steel Mesh
Physical Specifications
External Width (W)
19 in / 483 mm
External Height (H)
12.375 in / 314 mm
External Depth (D1)
6.25 in / 159 mm
External Top Surface Depth (D2)
4.1 in / 104 mm
Net Weight
21.2 lb / 9.6 kg
JL Audio CS110TG-TW3 Brochure
High Output Series 10-Inch 600-Watt Enclosed Subwoofer System, 2Ω Ported Enclosure
JL Audio's patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output. In the HO110-W6v3, the high power handling of the 10W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification.
JL Audio's patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer's direct output. This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 10W6v3, and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer. A steel mesh woofer grille insert can be purchased separately (Model: SGR-10W6v2/v3), if additional woofer protection is desired.
Finish: Dark gray, high-grade automotive carpet, with black carpet on woofer baffle. "JL AUDIO" is embroidered in silver on the side surface of the enclosure.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 200 - 600WNominal Impedance: 2Ω
General Specifications
Continuous Power Handling (RMS)
600 W
System Nominal Impedance
2 Ω
Enclosure Type
Chamber-coupled, slot-ported, rear-firing design
Finish
Dark gray carpet with black insert
Grille Included
No
Physical Specifications
External Width (W)
12.125 in / 308 mm
External Height (H)
14 in / 356 mm
External Depth (D1)
21.75 in / 552 mm
Net Weight
47.8 lb / 21.7 kg
JL Audio HO110-W6v3 Brochure
High Output Series 10-Inch 500-Watt Enclosed Subwoofer System, 2Ω Ported Enclosure
JL Audio's patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output.
JL Audio's patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates on one side of the woofer, coupling the port output to the woofer's direct output. This also provides the necessary surface area and port length to maximize the performance of the W3v3 driver.
This enclosure design has been carefully engineered to the optimum ported alignment for the 10W3v3, and has been fine-tuned through extensive real-world listening. This efficient system will produce superb output with as little as 150W of amplifier power, but performs best with 300 - 500W of power.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Three solid aluminum bars provide stylish and rugged woofer protection.
The angled-back design saves precious cargo space by allowing the enclosure to fit tightly against the back of a vehicle's rear seat.
Finish: Dark gray, high-grade automotive carpet, with black carpet on woofer baffle. "JL AUDIO" is embroidered in silver on the top surface of the enclosure.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 150 - 500WNominal Impedance: 2Ω
General Specifications
Continuous Power Handling (RMS)
500 W
System Nominal Impedance
2 Ω
Enclosure Type
Chamber-coupled, slot-ported, rear-firing design
Finish
Dark gray carpet with black insert
Grille Included
Aluminum Bar Grille
Physical Specifications
External Width (W)
29.5 in / 749 mm
External Height (H)
13.5 in / 343 mm
External Depth (D1)
12.0 in / 305 mm
External Top Surface Depth (D2)
7.5 in / 190.5 mm
Net Weight
34.7 lb / 15.74 kg
JL Audio HO110RG-W3v3 Brochure
Dual 10-Inch 2-Ohm 800-Watt Subwoofer-Enclosure for Select 2019-UP RAM-1500 Crew-Cab Trucks, with Reclining Rear-Seat
This generation of RAM’s big hauler combines a bold new design with major advancements in aerodynamics, technology and towing capabilities. Sadly, the spacious interior leaves little room for a high-performance subwoofer enclosure.
Fortunately, JL's engineers welcomed this challenge head on and developed a subwoofer solution that fills your Crew Cab with loads of deep bass output. Featuring an all-fiberglass, sealed enclosure design, this Stealthbox® houses two of JL Audio's revolutionary 10TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort. Rear seat folding and recline are unaffected, and we even left a spot on the enclosure that’s perfect for a clean, hidden amplifier installation!
Specifications
Contains two 10TW3-D8 Subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installation requires removal of under-seat storage divider panel, if equipped. Fits 1500 Crew Cab with reclining rear seat. Will not fit 2500 or 3500 models.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-5GRAMCCR/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Subwoofer-Enclosure for Select 2020-UP RAM 1500 Quad-Cab Vehicles
This generation of RAM’s big hauler combines a bold new design with major advancements in aerodynamics, technology and towing capabilities. Disappointingly, the original equipment audio systems lack the low-frequency output and performance you might expect.
Luckily, JL-Audio engineers are experts in maximizing bass from minimal space and developed a subwoofer solution that fills your Quad Cab with loads of powerful bass output. Featuring a 100% fiberglass, sealed enclosure design, this Stealthbox houses two of JL-Audio's innovative 10TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort or folding. Theyeven left space on the enclosure that’s perfect for a small, hidden amplifier installation!
The Hard Data: Contains two 10TW3-D8 Subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installation requires removal of rear underseat storage tray, if equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-5GRAMQC/10TW3 Manual
Single 10-Inch 500-Watt 2-Ohm Carpeted Fiberglass Subwoofer-Enclosure for Select 2002-2018 Dodge Ram 1500 Quad Cab, 2003-Up 2500 & 3500 Quad Cab & 2009-2018 1500 Crew Cab & 2009-Up 2500 & 3500 Crew Cab Trucks
Dodge's big hauler combines large sedan passenger comfort with tough pickup truck capabilities.
JL's Stealthbox® for the Quad Cab tucks under the rear seat on the passenger side and encloses a 10-inch driver for impressive sub-bass performance. Seat folding is unaffected and plenty of room is left on the driver side for amplifier installation or storage. Best of all, the Stealthbox® is essentially invisible once installed.
The Hard Data: Contains one 10W3v3-2 in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Installs under passenger side rear-bench seat. The seat folding function remains unaffected. Cup holders are not affected. Some models require removal of the passenger side metal floor extension located under the rear seat. Some models may require cutting and removal of the underseat carpet and/or carpet padding. Will not fit Mega Cab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-QDRAM/10W3v3 Installation Manual
Dual 10-Inch 600-Watt 2-Ohm Carpeted Fiberglass Subwoofer-Enclosure for Select 2002-2018 Dodge Ram 1500 Quad Cab, 2003-Up 2500 & 3500 Quad Cab & 2009-2018 1500 Crew Cab & 2009-Up 2500 & 3500 Crew Cab Trucks
Dodge’s big hauler combines large sedan passenger comfort with tough pickup truck capabilities, but does not have a lot of extra interior space for a bulky subwoofer enclosure.
JL's Stealthbox® for the Quad Cab® neatly negotiates these challenges and tucks under the rear seat, enclosing dual 10-inch thin line subwoofer drivers for impressive sub-bass performance. Seat folding and comfort are unaffected, and plenty of room is left in the center for amplifier installation or storage. Best of all, this Stealthbox® is essentially invisible once installed, but certainly noticeable when you fire up your favorite music and experience world-class sub-bass.
The Hard Data:Contains two 10TW1-4 subwoofer drivers in a sealed enclosure. 600 watt power handling. Wired for 2 ohm mono. Some models may require cutting and removal of the underseat carpet and/or carpet padding. Will not fit Standard Cab, '02-'08 Crew Cab, or Mega Cab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-QDRAMD/10TW1 Installation Manual
Single 300-Watt 2-Ohm Thin 10-Inch Stealthbox Subwoofer-Enclosure for Select 2018-Up Ford Expedition Vehicles, with OEM Subwoofer
Ford's full-sized SUV delivers first-rate comfort with outstanding gear-hauling capability and towing capacity. This is why JL's Stealthbox solution is designed to retain 100% of your cargo space, while delivering first-class bass performance.
This model replaces the stock subwoofer and installs discreetly behind the factory cargo area trim to protect and hide its 10-inch subwoofer.
The Hard Data: Contains one 10TW1-2 subwoofer in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs behind driver side panel in the cargo area. Requires removal of the OEM "subwoofer".
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-EXPED4G/10TW1 Installation Manual
Single 400-Watt 2-Ohm 10-Inch Stealthbox Subwoofer Enclosure for Select 2015-UP Ford F-150 SuperCab and 2017-UP SuperDuty SuperCab Trucks
Benefitting from JL's revolutionary thin-woofer technology, this Stealthbox® for F-150 SuperCab and SuperDuty SuperCab trucks is designed to install neatly under the rear seat with no intrusion on cab space.
Featuring an all-fiberglass, sealed enclosure design, JL's Stealthbox® houses a 10-inch TW3 thin-line subwoofer and fills your truck with loads of deep bass output. Seat folding and reclining are unaffected, and JL even incorporated a recess on the Stealthbox’s top for mounting an amplifier, if desired.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under rear bench seat and requires removal of the storage divider panel. Stealthbox® includes a steel-mesh grille to protect the driver. Does not affect folding or reclining of seat.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-F150SPRCB/10TW3 Installation Manual
Single 10-Inch 2-Ohm 300-Watt Subwoofer-Enclosure for Select 2019-UP Ford-Ranger SuperCrew Vehicles
Ford's mid-sized pickup promises practical utility and performance for everyday commutes or rugged terrains. To make every drive even more enjoyable, JL-Audio's Stealthbox solution tucks under the rear seat on the passenger side and encloses a 10-inch driver for impressive sub-bass performance. Seat folding is unaffected with plenty of room remaining on the driver side for storage. Best of all, the Stealthbox virtually disappears once installed.
The Hard Data: Contains one 10TW1-2 subwoofer in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs under passenger side rear seat in place of storage compartment. Will not fit SuperCab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-RNGSCG4/10TW1 Manual
Single 500-Watt 2-Ohm 10-Inch Subwoofer-Enclosure for Select 1998-2007 Ford-Excursion and F-Series SuperDuty Trucks with Front Bucket-Seats
If you drive Ford's biggest SUV or if your SuperDuty truck is equipped with bucket seats and a center console, this Stealthbox® model is right up your alley. Without infringing on people space and without being visible, it will fill your interior with rich, deep bass.
This compact unit installs inside the factory center console. The cup holders remain unaffected and some console storage is retained. A powerful JL Audio 10-inch subwoofer driver fires down into the floor for intense up-front bass presence.
The Hard Data: Contains one 10W3v3-2 in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside factory center console and fires down on the floor. Cupholders are not affected. For installation into front console only. Console storage is reduced. The factory console is not supplied with the Stealthbox®. After installation, the factory console is raised approximately 1.5 inches above the floor. Will not fit in SuperDuty trucks with bench seats. Will not fit consoles with rear cup holders and rear audio controls.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-SUPRCNSL/10W3v3 Installation Manual
Single 10-Inch 2-Ohm Thin 300-Watt Subwoofer-Enclosure for Select 2014-2018 Chevrolet-Silverado and GMC-Sierra Pickups, with Front Bucket-Seats and Factory-Console
GM’s third generation Silverado/Sierra gets a full redesign with a variety of enhancements including engine and technology upgrades. Regrettably, the factory audio systems still come up short when it comes to bass reproduction.
Designed to invisibly install in the factory console, this Stealthbox® adds impressive, high-quality bass, with zero loss of passenger space, storage space, or utility. The only thing you lose is that weak factory bass performance.
Featuring 100% fiberglass construction, this Stealthbox® is equipped with a down-firing 10-inch TW1 thin-line subwoofer in a sealed enclosure design.
The Hard Data: Contains one 10TW1-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside forward-most portion of front center console, without affecting storage space or cup holders. Replaces the OEM “subwoofer” system, if vehicle is so equipped. Will not fit trucks equipped with eAssist powertrain.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-3GSLVCNSL/10TW1 Installation Manual
Single 10-Inch Thin 300-Watt Subwoofer-Enclosure for Select 2015-2020 Cadillac-Escalade, Chevy-Suburban, Chevy-Tahoe and GMC-Yukon Vehicles, with front bucket-seats and factory center-console
The fourth generation full-size SUV from GM gets all-new, luxurious interiors, along with major enhancements in performance and technology. Unfortunately, the stock audio systems continue a track record of weak bass reproduction. There also isn’t much room for a conventional subwoofer design, without compromising people and cargo space.
To neatly solve this problem, JL's engineers have designed a subwoofer solution that installs invisibly, inside the factory console, with zero loss of console storage space.
Featuring 100% fiberglass construction, this Stealthbox® is equipped with a down-firing 10-inch TW1 thin-line subwoofer in a sealed enclosure design.
The Hard Data: Contains one 10TW1-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside forward-most portion of front center console, without affecting storage space or cup holders. Replaces the OEM “subwoofer” system, if vehicle is so equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-4GSUVCNSL/10TW1 Installation Manual
Single 10-Inch 2-Ohm 400-Watt Subwoofer-Enclosure for Select 2021-UP Large Chevrolet and GMC SUV Vehicles
GM's fifth-generation full-size SUV gets all-new, luxurious interiors, along with major enhancements in performance and technology. Unfortunately, the factory audio systems still lack quality bass reproduction. There also isn’t much room for a conventional subwoofer design, without compromising people and cargo space.
To overcome this challenge, JL-Audio engineers developed a subwoofer solution that installs invisibly, behind the driver's side cargo panel, with no loss of storage space. Featuring 100% fiberglass construction, this Stealthbox is equipped with one of JL's innovative, 10-inch TW3 thin-line subwoofers in a custom-formed, sealed enclosure.
The Hard Data: Contains one 10TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Stealthbox® installs behind the driver side cargo trim panel. Replaces the OEM “subwoofer” system, if equipped.
Applications
Escalade
Escalade ESV
Suburban
Tahoe
Yukon
Yukon XL
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-5GSUV/10TW3 Installation Manual
Single 10-Inch 2-Ohm 400-Watt Thin Subwoofer-Enclosure for Select 2014-Up Corvette C7 Stingray Vehicles
The seventh-generation Corvette establishes a new benchmark for performance and style, but like most sports cars, presents a challenge when it comes to achieving excellent bass performance.
This Stealthbox® solution is engineered for those wanting to keep most of the cargo space in the hatch. It is also designed to install without any screws or bolts and can be removed in seconds for track day and reinstalled just as fast. The factory targa-top stowage is not affected in any way by the Stealthbox®, so you can enjoy great bass with or without the top installed.
Inside this Stealthbox® is a potent JL Audio 10-inch thinline subwoofer driver in a sealed enclosure that is expertly matched to the Corvette's acoustics. Also available with dual 10TW3 drivers model.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2-ohm mono. Installs into driver side hatch storage compartment. Steel mesh grille is included to protect the subwoofer driver. Installation does not affect storage of targa-top. No holes need to be drilled for installation. Easy to remove and replace. Use of driver's side, rear storage compartment is lost with installation. Storage compartment lid must be removed for installation, but can be replaced if Stealthbox® is removed. Will not fit convertible model.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-C7CP1/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2014-Up Corvette C7 Stingray Dual-Driver Vehicles
The C7 Corvette offers an aggressive exterior and a jetfighter-like cockpit, along with major increases in horsepower, torque and technology. Still missing, however, is a real subwoofer system… even with the premium audio option.
To solve this problem, the JL Audio engineers developed a potent Stealthbox® design housing twin 10TW3 subwoofers in a sealed enclosure that mounts ahead of the rear axle, so as to preserve precious cargo space and maintain the C7’s excellent weight distribution. With up to 800W of power handling, this Stealthbox® delivers amazing sub-bass output matching your Corvette’s powerful engine, adding even more enjoyment to every minute you spend on the road. Also available with single 10TW3 driver model.
The Hard Data: Contains two 10TW3-D8 subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installs behind front seats in the forward section of the cargo area. Installation does not affect storage of targa-tops. Steel mesh grilles are included to protect the subwoofer drivers. Will not fit convertible model.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-C7CP2/10TW3 Installation Manual
10-Inch 2-Ohm 400-Watt Thin Subwoofer-Enclosure for Select 2015-2022 Chevrolet-Colorado and GMC-Canyon Crew-Cab Vehicles
GM’s mid-size truck returns with major enhancements in power and technology, all packaged in a larger body and upscale interior with all the trimmings. Unfortunately, the factory audio systems are still lacking in the bass delivery department.
JL's Stealthbox® features an all-fiberglass, sealed enclosure design that installs under the rear seat and requires no holes to be drilled for installation. Equipped with their revolutionary 10TW3 thin-line subwoofer, this Stealthbox® fills your truck with powerful, deep JL Audio bass, with no intrusion on cab space.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under the rear bench seat. Does not affect folding or reclining of seat. Requires removal of under seat storage tray.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-COCREW2G/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2014-2018 (Gen 3) Chevrolet-Silverado and GMC-Sierra Crew-Cab Trucks
This generation of Chevrolet/GMC trucks is bringing new levels of interior refinement and technology to the full-size truck segment. JL's Stealthbox® enhances all this by adding impressive, high-quality bass without losing any of your precious people space or interior functionality.
The Stealthbox® slips under the truck's rear seat and features two of JL Audio's revolutionary 10TW3 thin-line subwoofers, giving you absolutely stellar sub-bass impact and quality. They even left a perfect spot in the middle of the enclosure for a clean, hidden amplifier installation!
The Hard Data: Contains two 10TW3-D8 subwoofers in a down-firing sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs under rear seat. Will not affect the folding of the rear seat or rear leg room.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCC3/10TW3/BK2 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 1999-2006 Chevrolet-Silverado, GMC-Sierra Crew-Cab Trucks and 2007 Crew-Cab-Classic Trucks
The massive GM Crew Cab trucks offer limousine-like rear seat room and comfort, accomplished by effectively utilizing almost every cubic inch of interior space. JL Audio's Stealthbox® for these big trucks slips behind the rear seat and features twin 10TW3 subwoofers for absolutely stellar sub-bass impact and quality. Nobody will ever know it's there, until you turn it up.
The Hard Data: Contains two 10TW3-D8 subwoofers in a sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs behind the rear seat. Will not affect the folding of the rear seat or rear leg room.
Applications
CHEVROLET
Silverado 1500, 2500, 3500
1999-2006
Silverado Classic
2007
GMC
Sierra 1500, 2500, 3500
1999-2006
Sierra 1500 Classic
2007
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCRW/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 600-Watt Thin Subwoofer-Enclosure for Select 2014-2018 Chevrolet-Silverado and GMC-Sierra Extended-Cab Trucks with Jet-Black or Dark-Ash Interior
Whether your GM truck is used to work hard or play even harder, it brings a whole lot to the table, including great towing and hauling capabilities, a spacious interior and a smooth ride.
JL's Stealthbox® enhances your GM truck by adding quality JL Audio bass without losing much of your precious space or interior functionality.
Inside this Stealthbox®, two of JL Audio's revolutionary 10TW1 thin-line subwoofer drivers deliver absolutely stellar sub-bass impact and quality.
The Hard Data: Contains two 10TW1-4 subwoofers in a sealed enclosure. 600 watt power handling. Wired for a 2 ohm load. Installs under rear seat. Will not affect the folding of the rear seat or rear leg room. Installation requires removal of plastic storage tray under rear seat (if equipped). Will not fit Crew Cab or Standard Cab trucks.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVD/10TW1/BK Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2019-UP Chevrolet-Silverado and GMC-Sierra Double-Cab Trucks
The fourth generation of GM’s full-size truck boasts major enhancements in technology and power, all packed in a larger body with a refined interior. Sadly, the factory audio options are still deficient in the bass delivery department.
JL Audio's Stealthbox® for the Double Cab version features an all-fiberglass, sealed enclosure design that mounts under the rear seat and requires no holes to be drilled for installation. Outfitted with a pair of JL's revolutionary 10TW3 thin-line subwoofers, this Stealthbox® fills your truck with stunning amounts of JL Audio bass, with no intrusion on cab space. They even left a recess on the Stealthbox's top for amplifier installation, if desired.
The Hard Data: Contains two 10TW3-D8 subwoofers in a down-firing sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs under rear bench seat. Will not affect the folding of the rear seat or rear leg room. Requires removal of under-seat storage tray, if so equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVD4/10TW3 Installation Manual
10-Inch 2-Ohm 300-Watt Subwoofer-Enclosure for Select 2007-2013 Chevrolet and GMC Full-Size SUV’s or Trucks with Front-Bucket-Seats
This generation of GM's big trucks and SUV's sets new standards for interior quality and luxury. There also isn't much wasted space in which to install a conventional subwoofer design without giving up cargo and people space.
JL's Stealthbox® solution installs inside the forward section of the factory center console for complete invisibility. Intense, up-front bass is produced by a down-firing 10-inch subwoofer in a sealed enclosure. The console's functionality and storage space is unaffected by the Stealthbox®.
The Hard Data: Contains one 10W1v3-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside forward-most portion of front center console and replaces the OEM “subwoofer” system, if vehicle is so equipped. Will not fit Trucks with AC vents on the back of the center console or vehicles with deep storage area in front of cup holders. Will not fit Full-Size “Classic” Trucks, Chevrolet SSR, Cadillac Escalade, Cadillac Escalade ESV, Cadillac Escalade EXT, Hummer H2, Hummer H2 SUT.
Applications
CHEVROLET
Avalanche
2007-2013
Silverado 1500, 2500 HD, 3500 HD
2007-2013
Suburban
2007-2013
Tahoe
2007-2013
Yukon
2007-2013
Yukon XL
2007-2013
GMC
Sierra 1500, 2500 HD, 3500 HD
2007-2013
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-TAHOCNSL/10W1v3 Installation Manual
10-Inch 2-Ohm 300-Watt Subwoofer-Enclosure for Select 2005-2013 Chevrolet C6-Corvette
The sixth-generation Corvette is an amazing performance car but it can definitely benefit from a major upgrade in the low-frequency department. This Stealthbox® tucks neatly into the rear corner of the hatch and uses the storage pocket space to gain volume without taking up much hatch space and without interfering with targa top stowage.
The Hard Data: Contains one 10W1v3-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs in driver-side corner of the hatch. A steel mesh grille is included to protect the subwoofer driver. Does not affect storage of Targa Top or access to fuel door and emergency door release. Will not fit convertible or ZR-1 models.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-VETC6/10W1v3 Installation Manual
10-Inch 2-Ohm 500-Watt Subwoofer Enclosure for Select 2011-2021 Jeep Grand-Cherokee with Black or Light-Frost Interior
The Grand Cherokee's pedigree for off-road prowess, comfort and everyday utility is well-represented by this generation of the venerable nameplate. We know that Jeep owners value the “go-anywhere, do-anything” capabilities of their vehicles. A bulky subwoofer enclosure that takes up valuable cargo space is not part of that experience, so JL Audio was pleased to present this beautiful Stealthbox® solution for the Jeep Grand Cherokee owner seeking great audio performance.
The Stealthbox® replaces the OEM “subwoofer” with a sealed enclosure housing a potent 10-inch JL Audio subwoofer driver. The enclosure installs in the passenger side rear corner of the cargo area without interfering with under-floor storage or cargo tie-down fixtures, while the included steel mesh grille keeps the driver safe from cargo-related mishaps.
The Hard Data: Contains one 10W3v3-2 subwoofer in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Black steel mesh woofer grille is included. Installs into passenger-side rear cargo panel and requires removal of factory “subwoofer”, if so equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-GCHWK2/10W3v3 Installation Manual
10-Inch 2-Ohm 300-Watt Subwoofer Enclosure for Select 2007-2017 Jeep Wrangler (JK) 2-Door with Black-Interior
The original American off-road machine is made for getting dirty and finding places that nothing else with four wheels and four seats can reach, but it's not really made for great bass. Let's see what we can do about that.
This low-profile Stealthbox® system sits inconspicuously on the cargo-area floor and features a rigid, carpet-covered, removable panel that conceals a powerful 10-inch subwoofer driver and a secure mounting place for a JL Audio amplifier (sold separately). The subwoofer driver is housed in a sealed, carpet-covered fiberglass enclosure. The entire structure is designed to be easily installed and removed when the tailgate is opened, so you can choose to remove it if you plan to get your Jeep really filthy or need the extra space.
The Hard Data: Contains one 10W1v3-2 subwoofer in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs on floor of the rear cargo area. Floor of cargo area is raised approximately 5 inches with installation. Will not affect rear seat-folding functionality. Cannot be used without the factory tailgate in place.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-JK2DR/10W1v3 Installation Manual
10-Inch 300-Watt 2-Ohm or 4-Ohm Subwoofer Enclosure for Select 2018-2023 Jeep Wrangler-Unlimited, Driver Side
Combining JL's advanced thin-line subwoofer technology with a form fitting enclosure design, these Stealthbox® systems deliver outstanding sub-bass performance in your 4-door Wrangler, without consuming excess cargo space.
Constructed from 100% fiberglass, each Stealthbox® houses a 10TW1 thin-line subwoofer and mounts solidly above each rear wheel well. A matching trim panel and sturdy steel-mesh grille are included, so you can carry plenty of gear without worrying about damage. Separate driver and passenger side Stealthbox® models are available, each with 2 or 4 ohm drivers.
The Hard Data: Contains one 10TW1 in a sealed enclosure with 300 watt power handling. Choose from 2 ohm or 4 ohm models, driver or passenger side. Each enclosure installs above one rear wheel well. Black steel mesh grille is included with each.
If vehicle is factory-equipped with Premium Audio, passenger side Stealthbox® installation requires removal of OEM “subwoofer” and purchase of interior trim parts from Jeep®.
Will not fit any "JK" Jeep® model or 2-Door "JL" models.
Soft-top models: Stealthbox® installation does not interfere with normal top operation, except for the final position where the top mechanism is detached from the rails.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-JL4DDRV/10TW1-2 Installation Manual
10-Inch 300-Watt 2-Ohm or 4-Ohm Thin Subwoofer-Enclosure for Select 2018-2023 Jeep Wrangler-Unlimited, Passenger-Side
Combining JL's advanced thin-line subwoofer technology with a form fitting enclosure design, these Stealthbox® systems deliver outstanding sub-bass performance in your 4-door Wrangler, without consuming excess cargo space.
Constructed from 100% fiberglass, each Stealthbox® houses a 10TW1 thin-line subwoofer and mounts solidly above each rear wheel well. A matching trim panel and sturdy steel-mesh grille are included, so you can carry plenty of gear without worrying about damage. Separate driver and passenger side Stealthbox® models are available, each with 2 or 4 ohm drivers.
The Hard Data: Contains one 10TW1 in a sealed enclosure with 300 watt power handling. Choose from 2 ohm or 4 ohm models, driver or passenger side. Each enclosure installs above one rear wheel well. Black steel mesh grille is included with each.
If vehicle is factory-equipped with Premium Audio, passenger side Stealthbox® installation requires removal of OEM “subwoofer” and purchase of interior trim parts from Jeep®.
Will not fit any "JK" Jeep® model or 2-Door "JL" models.
Soft-top models: Stealthbox® installation does not interfere with normal top operation, except for the final position where the top mechanism is detached from the rails.
Jeep Part #CFWLR-74-24 carpet needs to be ordered from jeep to remove the Factor Subwoofer.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-JL4DPAS/10TW1-2 Installation Manual
Dual 10-Inch 600-Watt 2-Ohm Thin Subwoofer-Enclosure for Select 2020-UP Jeep Gladiator-JL Vehicles
More than just a Jeep pickup, the Gladiator is an accomplished off-road vehicle with dramatic styling and advanced technology features. JL Audio's Stealthbox® enhances all this by adding impressive, high-quality bass without losing any of your precious people space or interior functionality.
Featuring an all-fiberglass, sealed enclosure design, this Stealthbox® houses two of JL's innovative 10TW1 thin-line subwoofers and mounts neatly under the rear seat, without compromising rear passenger comfort. Rear seat folding is unaffected, and they even left space on the enclosure that’s perfect for a clean, hidden amplifier installation!
The Hard Data: Contains two 10TW1-4 Subwoofers in a sealed enclosure. 600 watt power handling. Wired for 2 ohm mono. Installation requires removal of under seat storage compartment, if equipped. Retains hardtop hardware storage box and jack stowage.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-JTGLAD/10TW1 Installation Manual
Single 10-Inch 300-Watt 2-Ohm or 4-Ohm Thin Subwoofer-Enclosure for Select 2007-2017 Jeep-Wrangler JK-Unlimited with Black-Trunk, Driver Side
Whether your adventures are urban, suburban or on the roughest trails... these Stealthbox® systems for the 4-door Wrangler Unlimited will make them all more exciting.
These systems are designed to provide powerful, audiophile bass quality without significantly compromising precious cargo space. JL Audios patented, low-profile thinline subwoofer technology extracts amazing bass from very thin enclosures that bolt solidly above each rear wheel well. Rugged, 100% fiberglass construction is as tough as your Jeep® and sturdy steel-mesh grilles mean you can still toss all your gear in the back without worrying about damage.
Because Jeep® owners customize their vehicles in all kinds of creative ways, the driver side and passenger side Stealthbox® systems are sold individually. A single one is enough for most people to be very happy, but you can go for two if maximum performance is your goal.
The Hard Data: Each system contains one 10TW1 in a sealed enclosure with 300 watt power handling. Each enclosure is wired for 2 or 4 ohms. A steel mesh grille is included with each to protect the subwoofer driver. Each enclosure installs above one rear wheel well, with specific models for passenger and driver side. Does not affect hard top installation.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-WRUD/10TW1-2 Installation Manual
Single 10-Inch 300-Watt 2-Ohm or 4-Ohm Thin Subwoofer-Enclosure for Select 2007-2017 Jeep-Wrangler Unlimited, Passenger Side
Whether your adventures are urban, suburban or on the roughest trails... these Stealthbox® systems for the 4-door Wrangler Unlimited will make them all more exciting.
These systems are designed to provide powerful, audiophile bass quality without significantly compromising precious cargo space. JL's patented, low-profile thin line subwoofer technology extracts amazing bass from very thin enclosures that bolt solidly above each rear wheel well. Rugged, 100% fiberglass construction is as tough as your Jeep® and sturdy steel-mesh grilles mean you can still toss all your gear in the back without worrying about damage.
Because Jeep® owners customize their vehicles in all kinds of creative ways, the driver side and passenger side Stealthbox® systems are sold individually. A single one is enough for most people to be very happy, but you can go for two if maximum performance is your goal.
The Hard Data: Each system contains one 10TW1 in a sealed enclosure with 300 watt power handling. Each enclosure is wired for 2 or 4-ohms. A steel mesh grille is included with each to protect the Subwoofer. Each enclosure installs above one rear wheel well, with specific models for passenger and driver side. Does not affect hard top installation.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-J-WRUP/10TW1-2 Installation Manual
Single 10-Inch 600-Watt 2-Ohm Subwoofer-Enclosure for Select 2013-Up Subaru BRZ, 2013-2016 Scion FR-S, and 2016-UP Toyota 86 Vehicles
Somebody finally paid attention and designed a no-nonsense, back-to-basics sports car that puts the emphasis on driving enjoyment. Now all you need to do is add a healthy dose of JL Audio to ratchet up the listening enjoyment and make every drive even more memorable.
JL's patented 10TW3 thin-line driver is the engine inside this Stealthbox® system, and it produces spectacular results from its perch in the passenger side rear corner of the trunk. Your trunk remains completely useful and your installation is neat and secure. A grille is also included to protect your investment.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in the passenger side of trunk compartment. Black steel mesh woofer grille is included.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-S-BRZFRS/10TW3 Installation Manual
Single 10-Inch 2-Ohm 400-Watt Subwoofer-Enclosure for Select 2010-UP Toyota 4Runner Vehicles
The 5th Generation 4Runner has been long-overdue for a Stealthbox solution. When JL finally approached the challenge, thy knew 4Runner owners cared about the vehicle's cargo space and JL-Audio didn't want to interfere with OEM cargo slides or aftermarket cargo drawer systems. The result is the addition of a spectacular 400 watt, 10-inch subwoofer solution tucked nicely behind the factory cargo panel.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs behind factory panel in the passenger side rear cargo area. Subwoofer is protected by the included black steel mesh grille and concealed by a fabric grille. Installation requires permanent modification to the factory panel. Installation in models equipped with an "OEM" subwoofer require purchase of a standard factory panel from Toyota Parts. Will not fit models with third row seating.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-T-4RNRG5/10TW3 Installation Manual
