At this present time our store location is open by appointment only.

Amplifiers

Automotive and Marine Audio Amplifiers.

Automotive, Power-Sport and Marine Grade Amplifiers

Amplifiers are the power plant of your car stereo system. They may be built to exist in the head unit and they are included on active speakers. Amplifiers are usually found externally as stand alone units between your head-unit and your speaker driver in the signal flow process. They come in various power output levels called watts. The amp essentially takes your media output from your receiver and boosts that signal to power a speaker driver. If your vehicle has an upgraded factory sound system like a Bose, Alpine or JBL then you most likely have a factory amplifier. Real Time Analyzation, or RTA tuning and time correction can make a dramatic difference in the final sound quality of your car stereo system and should be taken into consideration when updating the amplifier in your car.

Some amplifiers like the JL Audio VXi Series have built in time correction and tuning capabilities like a 9 band parametric equalizer per output channel. Amplifiers like the VXi amps have in depth tuning capability and are especially great for today’s newer cars with infotainment systems that are difficult to replace. RTA tuning is a process of time measuring the distance between the listening position and each speaker, and then measuring the frequency response of your speakers and your vehicles acoustic properties. After analyzing this information we can then begin to make real time adjustments with crossovers, parametric EQ’s and level balancing. When finished, the optimum tuned system will have the sound from each individual driver reach the listening position at the same time. Each speaker would be optimally level balanced to be the same volume and to reproduce all frequencies as flat as possible with adjustments to fight the acoustical imbalances of your vehicle.

Adding or replacing your amplifier?

Did your car stereo’s amplifier finally bite the dust? Do you want to level up on your car stereo game? Do you just require an upgrade in sound quality or do you just want some low end funk in your trunk? Whatever your reason may be Jackson Tint and Sound can help you pick out the right amplifier and provide you with simply the best professional installation within your budget.

Location: Finding a home for your car stereo amplifier can be a challenge. A great go to first spot is under a seat but, will the amplifier’s height allow clearance to be mounted there? Will you be able to raise it up off the floor a bit to keep it away from moister? Will all the wires be safe from moving parts? Will the rear passenger’s feet hit the amplifier? Finding a location to mount your car or truck amp is not always easy and is not something you want moving around or near water. A good amplifier location should be dry, secured, vented and protected.

RMS power: The RMS power rating of any car-amp is the continuous power rating that the amplifier is designed to output at a maximum volume rating. The RMS rating is one of two numbers to go by when pairing your speakers with a power-plant. As an example a speaker with a 100-Watt, or 100W for short, RMS rating should be paired with a 100W RMS amplifier. We usually recommend an amplifier to be over powered by 10 – 20% RMS so that the amplifier does not have to work at 100% capacity to get 100% efficiency from your speakers. This will keep your amp from overheating during long periods of continuous operation.

Ohms: The Ohm rating, or resistance rating, of an amplifier is the second most important when pairing drivers with power-plants. An amp that is 750W @ 2-ohms might only generally be 500W or less @ 4-ohms. When purchasing a car stereo amp, the correct pairing of a speaker’s RMS wattage and Ohm ratings with the correct power-plant output rating is absolutely essential.

Signal to Noise Ratio or S/N: The measurement of volume in any sound system is noted by the Decibel, or dB for short. 6dB is perceived by the human ear to be double the volume. 96dB is essentially twice as loud as 90dB. With that said, the S/N ratio of your car stereo amplifier is the measurement of dB’s between the inherent noise produced by the electronics within the amplifier and the level of amplified source volume. The S/N rating is by all means a measurement of how quiet that piece of audio gear is. It is a measurement of separation.

Every piece of audio electronics will have an induction of noise and should have a S/N ratio measurement in the specifications. Noise is usually introduced during the analog to digital, or A/D for short, and digital to analog, or D/A for short, conversions. Every time a piece of your car car stereo gear has to make this conversion noise is introduced into your sound system. Analog amplifiers can be noisy due to the analog electronics amplifying the input signal. Digital amplifiers eliminate this noise but still have some noise in the A/D and D/A converters.

A car stereo amplifier with a S/N ratio of 90db will hiss twice as loud than an amplifier with a 96db S/N ratio when silent. Essentially this rating transmits to unwanted hum and hiss from your speakers and degradation in the quality of your car stereo speaker system's performance. Some amplifiers like the JL Audio VXi Series have Toslink optical inputs for connecting digitally to other Toslink devices. This keeps the incoming audio signal clean and reduces numerous analog to digital conversions. When comparing differences between multiple amplifiers of equal wattage, the S/N ratio should be taken into consideration when budgeting for an amplifier.

So Many Choices, Where Do I Begin?

Budget: With more affordable and moderately priced amplifier options from Kicker and Alpine to the high end audiophile quality of JL Audio’s VXi series amplifiers, the cost of installation is the same. Even if you are one of the do-it-your-self type, the effort required is still the same. Spending an extra $100 to $200 for an amp could very well last longer, will usually sound better, and will generally keep you satisfied with your car stereo purchase for years to come.

How many channels do you need? Are you going to amplify your door speakers or just your subwoofer? Maybe both? If so you need a 5ch amp. Maybe a 5ch amp won’t give you the power rating you desire for your subwoofer. If so you need a 4ch amplifier for your door speakers and a monoblock, single channel power plant for your sub.

RMS and Ohms: Is the power rating and resistance rating going to match the ratings of your door speakers and subwoofer? Will your amplifier produce at least the RMS level of your drivers? Balancing your amplifier power and resistance ratings with your speakers is critical to the design and budgeting of your car stereo for correct operation.

Functions and Capabilities: Why are you replacing or adding an amp and what kind of functionality do you want from it? Will it be exposed to water, dust or salt? Marine grade amplifiers for these applications one might find in a boat, convertible or an ATV are specially designed to be water resistant and host corrosive resistant components and added protection from salt water, dust and debris.

Essentially no matter what speakers, amplifiers or subwoofers you have in your car these devices only sound as good as the quality of the source media and the dedication to building them. Pairing a full set of JL Audio speakers and subwoofers for instance with a Pioneer amplifier is a waste of your JL Audio speaker system's potential. With that said, your amplifier will only sound as good as your media type. Compressed audio from an MP3 streaming over BT will never sound as good as a 16bit 48kHz audio file, like what you would find on a CD, or a 32bit 96kHz high quality audiophile format, like what you would generally find on a Blu-Ray disc or now FLAC files. Now you can even put everything onto a USB thumb drive as a media option.

10 products

  • JL Audio VX700/5i : 5ch Digital Amplifier with DSP, 700W or 480W @ 2Ω or 4Ω JL Audio VX700/5i : 5ch Digital Amplifier with DSP, top.

    JL Audio VX700/5i : 5ch Digital Amplifier with DSP, 700W or 480W @ 2Ω or 4Ω

    Pre-Order Today!

    5-Channel Class-D System Amplifier with Integrated DSP, 75-Watt x 4 @ 4-Ohm + 300-Watt x 1 @ 2-Ohm Designed to simplify great audio, every VXi amplifier combines JL's advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. Employing JL's second generation NexD2™ amplifier technology, the VX700/5i efficiently powers a complete audio system. It can drive four main speakers with 75 W x 4 @ 4 ohms while also powering a subwoofer with up to 300W @ 2 ohms. Bridging the main channels converts it into a very powerful, 3-channel system amplifier with up to 200W x 2 @ 4 ohms on the main channels and 300W @ 2 ohms on the subwoofer channel. The NexD2™ full-range technology in the main channels of this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The subwoofer channel features an optimized low-frequency variant of the NexD2™ technology. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. Amplifier includes: Power Connector (for 4 AWG wire), Analog Input/Pre-Out Harness, Speaker Output Harness, Subwoofer Output Harness, 6 ft A/B USB Cable TüN™ Software Applications Intuitive setup and tuning, all at your fingertips. Automatically recognizes connected amplifier and displays appropriate interface. TüN™ is available for download for free in a variety of applications, for computers and most handheld devices.= Unprecedented, Onboard DSP Tuning Power Premium, triple-core AKM® DSP with an optimized configuration, developed in collaboration with AKM® Hi-Res audio processing at 24 bit/96 kHz High-performance AKM® A/D and D/A converters 10 Bands of fully parametric EQ, per output channel, including pre-outs Shelving EQ option for Band 1 and Band 10 High-Pass & Low-Pass Filters for each output channel, with selectable alignments and slopes: Linkwitz-Riley: 12, 24, 48 dB/octaveButterworth: 6, 12, 18, 24, 36, 48 dB/octave Signal Delay in 0.01 millisecond steps (equivalent to 1/8-inch, 3 mm) All-Pass Filter (Phase EQ), with variable "Q" and corner frequency Polarity Reversal (0 or 180 deg.) Output Level Trim in 0.1 dB steps NexD2™ Switching Amplifier Technology JL's latest generation of high-speed switching technology delivers superb low frequency power and efficiency. Specially optimized for subwoofer applications Ultra-Versatile Analog and Digital Inputs High-performance, differential-balanced analog inputs for outstanding noise rejection Accepts speaker level signals from 200 mV, up to 16V RMS, including those from many factory systems Optical Digital (Toslink) input permits direct connection of S/PDIF digital sources, bypassing A/D converter. Accepts up to 24 bit/192 kHz input. Independently configurable RCA analog and digital pre-outs (24 bit/96 kHz) Automatic turn-on options via Signal-Sensing or DC-Offset sensing Functional Compact Chassis Design Solid cast alloy main unibody and bottom plate deliver superb EMI performance and shielding All connections utilize compact mating connectors for maximum integrity and fitment into tight spaces. Configurable LED logo ring displays status and can display audio preset color code or user-defined color Logo badge can be oriented in 90 degree increments Corner caps engineered to conceal mounting holes and hardware JLid™ System Command and Control with Networking Capabilities JL Audio's digital protocol provides control interface and communication between VXi amplifiers and optional JLid™ accessories, including: DRC-100/DRC-200/DRC-205 Digital Remote Controllers: Offers convenient level and DSP preset control from the driver's seat. VXi-BTC Bluetooth® Communicator: Permits wireless configuration of VXi amplifiers using your compatible Apple® or Android® device. VXi-HUB Optical Network Hub: Provides network connectivity for up to five slave VXi amplifiers, allowing synchronization of DRC controllers and DSP presets. Up to two VXi-HUBs can be daisy-chained to network up to ten VXi amplifiers. Specifications Frequency Response (Main Channels) 12 Hz - 24 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 12 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Analog Inputs - Main Channels) 99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to highest rated power (Analog Inputs - Subwoofer Channel) 99 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W (Analog Inputs - Main Channels) 80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W (Analog Inputs - Subwoofer Channel) 72 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to highest rated power (Digital Inputs - Main Channels) 101 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to highest rated power (Digital Inputs - Subwoofer Channel) 102 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W (Digital Inputs - Main Channels) 82 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W (Digital Inputs - Subwoofer Channel) 80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >50 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 16 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™) Main Channels @ 4 Ω 75 W RMS x 4 Main Channels @ 2 Ω 100 W RMS x 4 Main Channels - Bridged @ 4Ω 200 W RMS x 2 Subwoofer Channel @ 4 Ω 180 W RMS x 1 Subwoofer Channel @ 3 Ω 240 W RMS x 1 Subwoofer Channel @ 2 Ω 300 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A JL Audio VX700/5i Manual

    Pre-Order Today!

    $1,399.99

  • JL Audio XDM700/5 : 5ch Marine Amplifier, 75W x 4ch + 300W @ 2Ω JL Audio XDM700/5 : 5ch Marine Amplifier, top side.

    JL Audio XDM700/5 : 5ch Marine Amplifier, 75W x 4ch + 300W @ 2Ω

    Pre-Order Today!

    XDM-Series Five-Channel Class-D Marine-Grade Amplifier, 75-Watts x Four-Channels @ 4-Ohm and 300-Watt Mono @ 2-Ohm The XDM700/5 is ideal for a complete audiophile-grade, subwoofer + four satellite system, and fits comfortably in just about any vehicle or vessel. With this incredible little amplifier, you can drive two pairs of quality component speaker systems with plenty of clean power (75W x 4 @ 4Ω), while also generating a solid 300W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's high-speed NexD switching amplifier design. Suitable for car or boat installations, the XDM700/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM700/5 includes a 12dB / octave high-pass filter for one main channel pair, a 12dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500Hz or 500-5000Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications Main Channels @ 4 Ω 75 W RMS x 4 @ 14.4V Main Channels @ 2 Ω 100 W RMS x 4 @ 14.4V Main Channels - Bridged @ 4Ω 200 W RMS x 2 @ 14.4V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 14.4V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 14.4V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 14.4V Subwoofer Channel @ 1.5 Ω N/A Main Channels @ 4 Ω 60 W RMS x 4 @ 12.5V Main Channels @ 2 Ω 90 W RMS x 4 @ 12.5V Main Channels - Bridged @ 4Ω 180 W RMS x 2 @ 12.5V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 12.5V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 12.5V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 12.5V Subwoofer Channel @ 1.5 Ω N/A Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™) Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 5 kHz Filter Mode(s): Channels 3 & 4 (rear) High-Pass or Bandpass Filter Slope(s): Channels 3 & 4 (rear) 12 dB/octave Filter Frequency Range: Channels 3 & 4 50 Hz - 500 Hz Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 6.15 lb / 2.79 kg JL Audio XDM700/5 Manual

    Pre-Order Today!

    $899.99

  • JL Audio XDM500/3 : 3ch Marine Amplifier, 75W x 2ch + 300W @ 2Ω. JL Audio XDM500/3 : 3ch Marine Amplifier, top side.

    JL Audio XDM500/3 : 3ch Marine Amplifier, 75W x 2ch + 300W @ 2Ω

    Pre-Order Today!

    XDM-Series Three-Channel Class-D Marine-Grade Amplifier, 75-Watts x Two-Channels @ 4-Ohm and 300-Watt Mono @ 2-Ohm Small enough to fit in just about any tight space application, the XDM500/3 is the perfect amplifier for a simple audiophile-grade, subwoofer / satellite system. With its three channels of versatile output, you can drive a pair of quality component speaker systems with plenty of clean power, while also delivering a stout 300W to your subwoofer system. The technology that makes this much power possible in such a small chassis is JL-Audio's advanced NexD switching amplifier design. Suitable for car or boat installations, the XDM500/3 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM500/3 includes a 12dB / octave high-pass filter for its main channels, plus a variable slope low-pass filter for its subwoofer channel. Both filters offer continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications Main Channels @ 4 Ω 75 W RMS x 2 @ 14.4V Main Channels @ 2 Ω 100 W RMS x 2 @ 14.4V Main Channels - Bridged @ 4Ω 200 W RMS x 1 @ 14.4V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 14.4V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 14.4V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 14.4V Subwoofer Channel @ 1.5 Ω N/A Main Channels @ 4 Ω 60 W RMS x 2 @ 12.5V Main Channels @ 2 Ω 90 W RMS x 2 @ 12.5V Main Channels - Bridged @ 4Ω 180 W RMS x 1 @ 12.5V Subwoofer Channel @ 4 Ω 180 W RMS x 1 @ 12.5V Subwoofer Channel @ 3 Ω 240 W RMS x 1 @ 12.5V Subwoofer Channel @ 2 Ω 300 W RMS x 1 @ 12.5V Subwoofer Channel @ 1.5 Ω N/A Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >120 / 50 Hz Damping Factor @ 2 Ω >60 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 500 Hz Filter Mode(s): Channels 3 & 4 (rear) N/A Filter Slope(s): Channels 3 & 4 (rear) N/A Filter Frequency Range: Channels 3 & 4 N/A Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes (1&2/Sum/Sub) Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 4.8 lb / 2.18 kg JL Audio XDM500/3v2 Manual

    Pre-Order Today!

    $649.99

  • JL Audio XDM300/1 : Mono Marine Amplifier, 300W/200W @ 2Ω/4Ω. JL Audio XDM300/1 : Mono Marine Amplifier, top side.

    JL Audio XDM300/1 : Mono Marine Amplifier, 300W/200W @ 2Ω/4Ω

    Pre-Order Today!

    XDM-Series Monoblock Class-D Marine-Grade Amplifier, 300-Watts @ 2-Ohm or 200-Watts @ 4-Ohm This little monoblock powerhouse employs JL-Audio's high-speed NexD switching design to achieve unprecedented efficiency and amazing power output for its size. It is small enough to fit in most tight space applications, including small boats, pickups, motorcycles and UTV’s (in a weather-tight compartment). Designed for car or boat installations, the XDM300/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Targeted specifically for subwoofer applications, the XDM300/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 200 W RMS x 1 @ 14.4V @ 3 Ω 250 W RMS x 1 @ 14.4V @ 2 Ω 300 W RMS x 1 @ 14.4V @ 1.5 Ω N/A @ 4 Ω 160 W RMS x 1 @ 12.5V @ 3 Ω 210 W RMS x 1 @ 12.5V @ 2 Ω 270 W RMS x 1 @ 12.5V @ 1.5 Ω N/A Frequency Response 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >100 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >120 / 50 Hz Damping Factor @ 2 Ω >60 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter none Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Height (H) 2.05 in / 52 mm Width (W) 6.85 in / 174 mm Depth (D) 7.09 in / 180 mm Net Weight 3.8 lb / 1.72 kg JL Audio XDM300/1 Manual

    Pre-Order Today!

    $499.99

  • Kicker 46CXA6605t : Five-Channel Amplifier, 65-Watts x 4ch +, 300-Watts x 1ch at 2-Ohm or 150W @ 4-Ohm 5ch Amplifier - 65W x 4 + 300W @ 2Ω, or + 150W @ 4Ω : Kicker 46CXA6605t top side view.

    Kicker 46CXA6605t : 5ch Amplifier - 65W x 4 + 300W @ 2Ω, or + 150W @ 4Ω

    Pre-Order Today!

    Five-Channel Amplifier, 65-Watts x 4ch +, 300-Watts x 1ch at 2-Ohm or 150W @ 4-Ohm This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash. Efficient Class-D amplifier Three-second turn-on/off delay to eliminate unwanted interference Variable 12dB crossovers provides control to dial in perfect sound KickEQ™ 6dB variable bass boost for those additional low frequencies 24dB subsonic filter for protection from potentially damaging frequencies FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio Accepts up to 40-volt input signal Small footprint for easier installation Vertical mounting hardware included for another unique look This Kicker 46CXA6605t amplifier delivers as much as 300W into one bass channel. Specifications MODEL CXA660.5 Power (watts/ch) 4 Ohm Stereo 65x4 Power (watts/ch) 2 Ohm Stereo 90x4 Power (watts/ch) 4 Ohm Mono 180x2 Power (watts/ch) 4 Ohm Mono Sub Ch 150x1 Power (watts/ch) 2 Ohm Mono Sub Ch 300x1 CXRC Remote Bass Capable (sold sep.) yes Dimensions (in, cm) (all models 2-3/8, 5.9H x 6-3/4, 17 W x ...L)14-1/8, 35.7 Frequency Response (Hz): 10Hz-20kHz Frequency Response (Hz – Sub Ch.): 25Hz-200Hz Input Sensitivity: 250mV-10V (Low Level)1V-40V (High Level) Signal-to-Noise Ratio: 90dB Active Crossover: Amp 1-2: High Pass 10-200Hz @ 12dB/OctaveSub Channel: Low Pass 50-200Hz @ 12dB/Octave Subsonic Filter: 25Hz @24dB/Octave KickEQ™ Boost Variable 0-6dB @40Hz Kicker 46CXA6605t Manual

    Pre-Order Today!

    $449.99

  • Alpine S-A55V : 460W Amplifier, 40W x 4ch + 300W Sub @ 2Ω

    Alpine S-A55V : 460W Amplifier, 40W x 4ch + 300W Sub @ 2Ω

    Pre-Order Today!

    Alpine S-Series 40-Watt x 4-Channel Power Amplifier with 300-Watt Sub Channel @ 2Ω The S-Series amplifiers are designed to fit anywhere. The S-A55V 5-Channel model measures at 11.25” W x 8” H x 2.25” D and can be mounted under seats or behind panels. It proves to be the all-in-one solution for a multi-amp system, so you can enjoy big power output in a limited installation space. The S-Series amplifiers contain technology that was previously only available in our premium line up of amplifiers, the R- and X-Series models. The S-Series models are based on Alpine’s intelligent amplifier platform that ensures superior sound reproduction and precision imaging. With an improved heat sink, and protection circuit design that eliminates thermal shut-down, your music will keep playing no matter where your drive takes you. Specifications Alpine's Class D amplifier circuit 40W RMS x 4 +200W RMS x 1(4Ω, 14.4V, ≤ 1% THD+N) 60W RMS x 4 +300W RMS x 1(2Ω, 14.4V, ≤ 1% THD+N) Bridged: 120W RMS x 2 (4Ω, 14.4V, ≤  1% THD+N) S/N >83dB (ref. 1W into 4Ω) THD+N ≤ 0.03% (ref. 1W into 4Ω) Frequency response =10Hz to 30kHz (+/-3dB) Damping Factor: CH 1/2/3/4 >100, CH 5 >750 Alpine S-A55V Manual

    Pre-Order Today!

    $429.99

  • Alpine KTA-30MW : Mono 300W RMS @ 2Ω Marine Amplifier Alpine KTA-30MW : Mono 300W RMS @ 2Ω Marine Amplifier, top view.

    Alpine KTA-30MW : Mono 300W RMS @ 2Ω Marine Amplifier

    Pre-Order Today!

    Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycles saddlebags. The KTA-30MW is ready for your adventures. It is weather resistant, rated at IP66 for protection again dust ingress and high-pressure water spray.  Its rugged chassis and high-quality waterproof connector can be used in installations where it will be exposed to the outdoor elements. Specifications Alpine's Class D amplifier circuit with Dynamic Peak Power (DPP) 300W RMS x 1@ 2Ω, 14.4V, ≤  1% THD+N 600W DPP x 1@ 2Ω, 14.4V, ≤1% THD+N >83dB S/N (ref. 1W into 4Ω) 0.1% THD (ref 1W into 4Ω) 20-400Hz Frequency response (+/-1dB) Cast Aluminum chassis Weather resistant (IP66 rating) OEM-grade connector wire harness Speaker/RCA inputs (selectable, High range=0.5-10V, Low range=0.2-4V) Sound control:LP filter – Off/LP, Fc=50-400Hz @ -24dB/Oct. (variable); Subsonic filter: Fc=5-40Hz (variable); Input gain settings (variable); Bass EQ: 0 to +12dB, Fc=50Hz (variable) No Manual Available

    Pre-Order Today!

    $419.99

  • Last One! JL Audio MX300/1 : 300W Mono Marine Amplifier @ 2Ω JL Audio MX300/1 : 300W Mono Marine Amplifier, side view.

    JL Audio MX300/1 : 300W Mono Marine Amplifier @ 2Ω

    1 Available for pickup

    MX-Series 300-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 160-Watt @ 4-Ohm Engineered specifically for powersports applications, the MX300/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. With a robust 300W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX300/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch. Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 12 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) @ 4 Ω 160 W RMS x 1 @ 3 Ω 220 W RMS x 1 @ 2 Ω 300 W RMS x 1 @ 1.5 Ω N/A JL Audio MX300/1 Manual

    1 Available for pickup

    $329.99

  • Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm, left side.

    Kicker 47KEY5001 : Mono Amplifier with Built-In DSP, 300W @ 2Ω

    Pre-Order Today!

    Kicker KEY-Series Mono Amplifier with Automatic EQ/DSP Processor, 300-Watts @ 2-Ohm Kicker KEY series amplifiers use a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker. The KEY500.1 delivers 300 watts RMS of power to your speakers at 2-ohms. Measuring less than eight inches long and only two inches high, the KEY500.1 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.  If the temperature reaches the threshold, the Kicker KEY500.1's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption! Specifications Power (watts/ch), 1 Ohm mono 500 Power (watts/ch), 2 Ohm mono 300 Power (watts/ch), 4 Ohm mono 150 Standard dimensions in.(H x W x L) 1-11/16 x 4-1/8 x 8-1/8 Metric dimensions cm(H x W x L) 4.3 x 9.2 x 20.7 Frequency Response (Hz): 10-160 Input Sensitivity: high level: 1V-40V / low level: 125mV-5V Signal-to-Noise Ratio: >90dB, a-weighted, re: rated power Selectable Electronic Crossover: Variable Low Pass 40-160 Hz, Variable High Pass 10-40 Hz What's in the Box: 1 - fuse holder1 - manual and installation hardware Kicker 47KEY5001 Manual

    Pre-Order Today!

    $279.99

  • Last One! Kicker 46CXA4001t : Mono 300W Amplifier @ 2Ω, or 150W @ 4Ω Kicker 46CXA4001t : Mono 300W Amplifier input section.

    Kicker 46CXA4001t : Mono 300W Amplifier @ 2Ω, or 150W @ 4Ω

    1 Available for pickup

    Mono Amplifier, 300-Watts at 2-Ohm, 150-Watts at 4-Ohm This CX-Series 1-channel amplifier by Kicker has an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash. Efficient Class-D amplifier Three-second turn-on/off delay to eliminate unwanted interference Variable 12dB crossovers provides control to dial in perfect sound KickEQ™ 6dB variable bass boost for those additional low frequencies 24dB subsonic filter for protection from potentially damaging frequencies FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio Accepts up to 40-volt input signal Small footprint for easier installation Vertical mounting hardware included for another unique look This Kicker 46CXA4001t amplifier delivers as much as 400W into one bass channel at 1-Ohm. Specifications MODEL CXA400.1 Power (watts/ch) 4 Ohm 150x1 Power (watts/ch) 2 Ohm 300x1 Power (watts/ch) 1 Ohm 400x1 CXRC Remote Bass Capable (sold sep.) yes Dimensions (in, cm): (all models 2 3/8, 5.9H x 6 3/4, 17W x ...L) 8 1/8, 20.6 Frequency Response (Hz): 25-200, +0/-1dB Input Sensitivity: 250mV-10V (Low Level)1V-40V (High Level) Signal-to-Noise Ratio: >95dB, a-weighted, re: rated power Active Crossover: Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter: 25Hz @24dB/octave KickEQ™ Boost Variable 0-6dB @40Hz Kicker CXA Mono Amplifier Manual

    1 Available for pickup

    $199.99

Login

Forgot your password?

Don't have an account yet?
Create account