Aftermarket Sound-Bar-Speaker Replacement Adapter-Plates for Select 2018-Up Jeep Wrangler and 2020-Up Gladiator JL & JT Vehicles
Don't limit your speaker upgrade to the size of the 4" factory speakers. Go bigger with the JP-1015, designed to fit a larger 6.5" aftermarket speaker and optional tweeter into the factory soundbar location.
Designed to adapt the factory 4” to 6.5” with a tweeter option
Speaker depth 3 5/8"
Mounting plate/cutting template included
Hardware included
Harness included
The sound bar must be removed for installation - add 1hr to install time. Dome light clips are stronger than the plastic they are attached to. Dome light clip mounts may break off during removal, JTAS does not carry liability associated with the dome light and customer accepts liability for dome light replacement should breakage occur.
Kit Includes:
(2) grille replacements
(2) cutting template/grille support
(8) speaker mounting screws
(12) grille replacement screws
(2) cutting template/grille support screws
(2) 7” speaker harnesses
(2) sound deadening padding
Metra JP-1015 Installation Manual
Aftermarket Dash-Speaker Replacement Enclosure Pods for Select 2018-Up Jeep Wrangler and 2020-Up Gladiator JL & JT Vehicles
Each pair of pods has an ABS housing that utilizes the factory mounting locations for a secure fit that will heighten the listening experience. The pods use the factory grommet and wiring and a Metra speaker adapter harness is included.
Driver and passenger specific dash replacement sealed speaker pods to install 6in to 6.75in speaker
Mounting positions for Chrysler three hole mount used by specific speaker manufacturers such as Alpine
Sealed enclosure (1) with a hole for the factory wiring grommet
4-inch speaker depth
Includes 12" speaker harness
Significant disassembly of the Dash is required to access these speaker pod locations. Add 2-hours to installation time.
Applications
JEEP
Gladiator
2020-2023
Wrangler
AKA "JL" for 2018
2018-2023
Metra JP-1014 Installation Manual
Fuse-Holder Mounting Bracket for Under-The-Hood Locations in Select 2018-UP Jeep Wrangler-JL and Gladiator-JL Vehicles
The SBA-J-JL-FHB Fuse Holder Bracket is designed to securely mount up to two JL Audio XB-MFBU-ANL Master ANL Fuse Blocks (sold separately). Engineered and Built in USA, the SBA-J-JL-FHB Fuse Holder Bracket requires no drilled holes and installs using factory hardware.
The Hard Data: Attaches to the vehicle's firewall using factory hardware. Fits 2-Door or 4-Door models. Will not fit Rubicon 392 or models equipped with the EcoDiesel engine.
Will not fit any 2018 "JK" Jeep® models.
JL Audio SBA-J-JL-FHB Installation Manual
Omega Add-on Customizable Remote Start System for Select Key-Turn-Start Vehicles, Operated with Factory Remote
Activates from almost any existing keyless entry or security system
Includes status light and override switch
Remote start compatible with gas or diesel engines!
Selectable engine run times!
Low voltage & low temp auto starting
Rear defrost activation output
Turbo timer - 1, 2, or 3 minute run time!
Enhanced audible remote start diagnostics
VIRTUAL ALARM
Flashing light output.
Optional anti-grind feature to protect your starter.
Silent pit-stop operation
2 data ports -- auto-detects protocol!
RK-Kit upgrade compatible
Linkr-LT compatible
Limited Lifetime warranty on all components.
Lifetime Warranty with our add-on Professional Remote Start installation.
Lifetime warranty on our un-altered installation
Lifetime warranty on the remote start and bypass system
Aftermarket DDIN-Size Radio-Replacement Kit for Select GM Full-Size Trucks and SUVs 1999-2002 - Matte Black
This replacement dashboard panel is engineered to help you install an aftermarket 4" tall (Double-DIN) radio so that you can upgrade the stereo much easier. Since the original dashboard on these older models cannot fit a larger radio, this replacement panel allows you to upgrade to a bigger, modern radio without complex or labor-intensive custom fabrication. It is painted scratch-resistant matte black to match the original look and feel of the vehicle's dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn't offer but requires this dash panel to make it fit.
Large panel replaces the factory dash panel
Provides the space for any standard 4" tall aftermarket radio
Painted scratch-resistant matte black. Also available: textured black (*DP-3002TB*), gray (*DP-3002GY*), shale (*DP-3002SHL*), and pewter (*DP-3002PWT*)
No custom fabrication work is required
Made from the highest quality ABS plastic for an original factory-like fit and finish
Wiring Harness
70-1858 (non-amplified models)(sold separately)
70-1859 (amplified models)(sold separately)
Antenna Adapter
40-GM10 (sold separately)
Applications
Chevy (models with message center in the factory instrument cluster)
Avalanche - 2002-2002
Silverado 1500 - 1999-2002
Silverado 2500 - 1999-2002
Silverado 3500 - 2001-2002
Silverado 3500 (commercial) - 2002-2002
Suburban - 2000-2002
Tahoe - 2000-2002
GMC (models with message center in the factory instrument cluster)
Sierra 1500 - 1999-2002
Sierra 2500 - 2000-2002
Sierra 3500 - 2001-2002
Yukon / Yukon XL (less Denali 01-02) - 2000-2002
Aftermarket Head-Unit Replacement Maestro-Module T-Harness for Select 2007-UP Chrysler, Dodge and Jeep Vehicles
Greatly simplifies the installation of the Maestro RR module. For back-up camera and rear seat entertainment the AVCH1 is also required.
Click Here to View Vehicle Compatibility - confirmed through 2020
Universal Head-Unit Replacement Interface for Select 2003-UP Vehicles
Maestro RR connects to iDatalink-compatible Alpine, JVC, Kenwood, Pioneer and SONY radios to enhance your multimedia experience with exclusive Gauges, Vehicle Info, Parking Assistance, Climate Control and Radar Detection screens while reataining all the factory infotainment features you love such as steering wheel controls, voice commands and more. Basic radio retention features are also available with non-iDatalink-compatible radios. Some accessories and aftermarket radio are required and sold separately.
Drone-Mobile Cellphone Remote-Start Add-on Remote-Control for Select Compustar Auto-Start Systems
Add DroneMobile smartphone control and GPS tracking to any Compustar remote start and security system. Built-in backup battery for added security. Powered by AT&T LTE for industry-leading coverage and reliability. For U.S. customers only. Free 30-Day Premium Trial included.
The DroneMobile X1 MAX adds LTE and GPS connectivity to any Compustar remote starter or alarm, enabling unlimited range control and tracking from your smartphone. Watch the DroneMobile Video to see how DroneMobile keeps you, your vehicles, and your family connected!
The Drone X1-MAX not only adds unlimited range smartphone control and GPS tracking to your vehicle, but it also protects your vehicle's security and health.
The X1-MAX Module has a built-in backup battery and security sensors to detect intrusion or battery tampering. In addition, the Drone X1-MAX includes an additional data harness for connecting your Drone X1-MAX
Compustar Firstech X1MAX-LTE Manual
DIN or DDIN-Size Aftermarket Stereo-Replacement Dash-Kit for Select 2016-2023 Toyota Tacoma Vehicles, (High Gloss Finish)
This stereo installation kit has been engineered to help you install either a 2” tall (Single-DIN) or a 4” tall (Double-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2” radio to fill the extra space in the radio opening, which can be used for storage. The pocket is not needed when installing a 4” tall radio. The dash kit is painted scratch-resistant matte black to match the original look and feel of the vehicle’s dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn’t offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2” or 4” tall aftermarket radio
Painted scratch-resistant matte black
Multiple trim plates are included to support all trim levels
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
TOYOTA
Tacoma
2016-2023
Metra 99-8251 Installation Manual
Head-Unit Replacement USB-Retention Adapter-Cable for Select 2006-UP Chrysler, GM and Ford Vehicles
Converts the factory USB port cable into standard full size male USB so it can be plugged into an aftermarket radio.
Click Here to View Vehicle Compatibility
300-Watt Door-Speaker and Add-On Subwoofer Kit for Select 2018-2023 Jeep Wrangler, Gladiator Vehicles
Complete Sound System Upgrade Package for the four-door, non-amplified 2018-23 Jeep® Wrangler and non-amplified 2020-23 Jeep® Gladiator. Also compatible with two-door, non-scissor front seats in 2019-23 Jeep® Wrangler
Go beyond your wildest expectations for sound with this complete sound upgrade package. The PSS-24WRA has 5-channels of powered sound that replaces your factory system. The package includes two sets of 6.5” weather-resistant mid-bas drivers and 1” weather-resist tweeters that replace the front and rear soundbar factory speakers, an 8” powered, compact subwoofer and a 4-channel power pack amplifier.
Specifications
Complete, five-channel powered sound system upgrade package
Compatible with four-door, non-amplified 2018-23 Jeep® Wrangler and non-amplified 2020-23 Jeep® Gladiator (not compatible with OEM Alpine amplified system)
Compatible with two-door, non-scissor front seats in 2019-23 Jeep® Wrangler
Includes Alpine’s SPV-65X-WRA, SPV-65-JLT, PWE-S8, and KTP-445U
180W, 4-channel Power Pack amplifier
120W, 8” powered subwoofer
(2x) 6.5” weather-resistant mid-bass drivers
(2x) 1” weather-resistant teteron dome tweeters with vehicle-specific connectors and crossovers
Vehicle-specific front speaker pods with vehicle-specific connectors
Tweeter adapter plates allow for the use of the original factory tweeter locations
SPV-65-JLT weather-resistant rear soundbar speaker system
Rugged, premium grills designed to emulate the factory look and appeal
Vehicle-specific connectors for plug-and-play speaker installation
Utilizes factory bolt locations
Durable stamped, steel frame speaker basket design
Includes template for mounting
Vehicle-specific T-harness for installation with OEM radio into compatible 2018-23 Jeep® Wrangler and 2020-23 Jeep® Gladiator vehicles
Vehicle-specific mounting brackets allow for the powered sub and amp to be secured under the passenger seat without drilling
What's in the Box:
KTP-445U Universal 4-Channel Power Amplifier
PWE-S8 8" Compact Powered Subwoofer
SPV-65X-WRA Front Component Speakers
SPV-65-JLT Rear Sound Bar Speakers
ALP-POD-JLT Front Speaker Pod
PSU-BKT-JL-R PWE Right Bracket JL
PSU-BKT-JL-L PWE Left Bracket JL
ALP-HRN-PSU300 PSU Power Harness
ALP-THRN-CH2 Chrysler T-Harness
CT6 6" Cable Ties
PHPSM412 Pan Head Phillips Screw M4x12
SLWM4 M4 Split Lock Washers
PHSCR832 8-32 Pan Head Phillips screws
PSS-WRA-IM Installation Manual
Specifications
Front (SPV-65X-WRA)
Power handling: 75 watts RMS (225 watts peak)
Frequency response: 65kHz – 22kHz
Nominal impedance: 4 ohms
Weather-resistant: IP55
Rear (SPV-65-JLT)
Power handling: 90 watts RMS (270 watts peak)
Frequency response: 50kHz – 22kHz
Nominal impedance: 4 ohms
Weather-resistant: IP55
Powered Subwoofer (PWE-S8)
120 watts RMS (240 watts peak)
Frequency response: 32 - 150Hz
Variable low-pass crossover (80-200 Hz)
Variable phase control (0-180 degrees)
preamp- and speaker-level inputs
Four Channel Power Pack Amplifier (KTP-445U)
45 watts RMS x 4 at 4 or 2 ohms
90 watts RMS x 2 bridged at 4 ohms
Selectable high-pass filters (60, 80, or 120 Hz at 12 dB/octave)
Switchable RCA or speaker-level inputs|
Dimensions:
27” L x 18.5” W x 19.5” H
40lbs
Direct fit for non-amplified 2018–Up 4-door Jeep Wrangler JL Unlimited
Direct fit for non-amplified 2019–Up 2-door Jeep Wrangler
Direct fit for non-amplified 2020–Up Jeep Gladiator JT
Alpine PSS-24WRA Installation Manual
Add-on RV and Camper Cell-Phone Booster with 5G Connectivity
Drive Reach RV is weBoost's powerful multi-user, in-vehicle cell signal booster for all RV classes. It’s designed to reach cell towers at distances up to 74% farther than the Drive RX RV
With its all-new omni-directional antenna, Drive Reach RV stops dropped calls while improving voice quality, data speeds, video streaming, and more whether at a campsite or on the road.
Drive Reach RV works on all U.S. carrier networks and is compatible with all phones and cellular devices as it simultaneously supports multiple users.
5G Compatible - weBoost is committed to the 5G movement, ensuring all their products work with 5G and support the latest in 5G technology.
weBoost Drive Reach RV BrochureweBoost Drive Reach RV Installation Guide
DIN or DDIN-Size Head-Unit Replacement Dash-Kit for Select 2009-2014 Ford F-150 Vehicles
This stereo installation kit has been engineered to help you install a 2" tall (Single-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2" radio to fill the extra space in the radio opening, which can be used for storage. The dash kit is painted scratch-resistant matte black to match the original look and feel of the vehicle's dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn't offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2" tall aftermarket radio
Painted scratch-resistant matte black
For vehicles without factory navigation
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
FORD
F-150
w/ CD, w/o color screen
2013-2014
F-150
FX, STX, XLT
2011-2012
F-150
SVT Raptor
2009-2012
F-150
FX, STX, XLT
2009-2010
F-150
XL w/ CD
2009-2014
Metra 99-5820B Installation Manual
DIN or DDIN-Size Head-Unit Replacement DIN or DDIN-Size Head-Unit Replacement Dash-Kit for Select 2005-2011 Toyota-Tacoma Vehicles, textured black
This stereo installation kit has been engineered to help you install either a 2” tall (Single-DIN) or a 4” tall (Double-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2” radio to fill the extra space in the opening, which can be used for storage. The pocket is not needed when installing a 4” tall radio. The dash kit is painted black and “golf ball” textured to match the original look and feel of the vehicle’s dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn’t offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2” or 4” (with an ISO-mount provision) tall aftermarket radio utilizing our patented quick-release, snap-in ISO mount system with custom trim ring
Painted black and “golf ball” textured (also available in gray: 99-8214TG)
Factory climate controls are retained in their current location
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
TOYOTA
Tacoma
w/ black color dash
2005-2011
Metra 99-8214TB Installation Manual
Forty-Eight-Inch-Long Motorola-Style AM/FM Antenna Extension-Cable
Easily extend your FM Antenna wire to reach a new mounting location or add-on to your existing connection to provide more length to install your new head-unit.
DIN or DDIN-Size Head-Unit Replacement Dash-Kit for Select 2005-2015 Nissan and Suzuki Vehicles
This stereo installation kit has been engineered to help you install either a 2” tall (Single-DIN) or a 4” tall (Double-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2” radio to fill the extra space in the radio opening, which can be used for storage. The pocket is not needed when installing a 4” tall radio. The dash kit is designed to match the original look and feel of the vehicle’s dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn’t offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2” or 4” tall aftermarket radio
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
NISSAN
Frontier
radio delete option
2016-2017
Frontier
S trim with King Cab(w/ or w/o radio delete option)
2013-2015
Frontier
S trim
2012-2012
Frontier
S, SE-4 cyl., XE
2009-2011
Frontier
all except Base model
2008-2008
Frontier
Base model
2008-2008
Frontier
2005-2007
Pathfinder
S
2008-2012
Pathfinder
2005-2007
Xterra
w/o 4.3-inch screen
2013-2013
Xterra
X trim, 4WD
2009-2012
Xterra
late production (w/ factory amp)
2008.5-2008.5
Xterra
late production (w/o factory amp)
2008.5-2008.5
Xterra
early production
2008-2008
Xterra
2005-2007
SUZUKI
Equator
extended cab
2009-2011
Metra 99-7635 Installation Manual
Universal 18-Inch Motorola Style FM-Antenna Extension-Cable
Easily extend your FM Antenna wire to reach a new mounting location or add-on to your existing connection to provide more length to install your new head-unit.
Remote-Start Add-On Wiring Harness for Select 2013-UP Honda and Acura Vehicles
Factory fit installation T-harness for select Honda and Acura poush-to-start models 2013 and up. Plugs directly into vehicle factory connectors with little-to-no analog connections required. Compatible with select iDatastart, Firstech, Flashlogic, Omegalink and Orbit branded remote start systems. Replaces ADS-THR-HA6.
Click Here to View Vehicle Coverage Information
Amplified Head-Unit Replacement Wiring-Harness Interface for Select 2005-2011 Mercedes-Benz E-Class, SLK, ML and GL Vehicles
*There are two different radio possibilities for this year range of vehicle, please see below for ways to distinguish between which interface kit you will need.
*Vehicles equipped with Command NTG1 will use the AXDIS-MB132. NTG1 radios will be built by Harman/Becker and have the 6-Disc Changer separate from the radio, if equipped with a SINGLE-disc player, it will be built in to the radio. They will typically have buttons on the sides of, and below the radio screen, also the optical light will come from the fiber cable when removed.
*Vehicles equipped with Command NTG2.5 will use the AXDIS-MB82. NTG2.5 radios will be built by Alpine, and have the 6-Disc changer built in to the radio. They will not have buttons directly below the radio screen, and the optical light will come from the radio when the fiber cable is removed.
Applications
MERCEDES
E-Class
2009
GL-Class
2007-2012
ML-Class
2006-2011
SLK-Class
2005-2011
Axxess Interface AXDIS-MB82 Manual
Replacement Tip-Sleeve Microphone for Select Alpine Head-Units
Replacement Microphone for Bluetooth enabled Alpine stereos with a tip and sleeve connector.
C2-Series 0.75-Inch 60-Watt Silk Dome Tweeters
The silk dome tweeter is prized by audiophiles for delivering realistic, non-fatiguing, high-frequency performance.
The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs.
Inline 12 dB / octave high-pass filters with tweeter protectors are included with this kit. The C2-075ct is designed to operate above 4 kHz with a minimum high-pass slope of 12 dB / octave.
Sonic character: Clean and Powerful
Sold as a pair.
General Specifications
Continuous Power Handling (RMS)
60 W
Peak Music Power*
150 W
Recommended Amplifier Power (RMS)
25 - 100 W / Ch.
System Efficiency
91.0 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
4 kHz - 22 KHz ± 3 dB
JL Audio C2-075ct Manual
Add-on Remote Start Wiring Harness for Select 2008-UP Audi, Bentley and Porsche Vehicles
Factory fit installation ‘T’-harness for select Audi, Bentley and Porsche models 2008-UP. Includes custom keybox for vehicles requiring a key for immobilizer bypass. Plugs directly into vehicle factory connectors with little-to-no analog connections required. Compatible with select iDatastart, Firstech, Flashlogic, Omegalink and Orbit branded remote start systems.
Click Here to View Vehicle Coverage
Punch-Series Stereo-Amplifier Bass-Knob
For use with select 2007 and newer PUNCH & POWER amplifiers.
Remote wired bass/treble boost
0dB to +18dB bass boost @ 45 Hz
0dB to +12dB treble boost @ 12.5 kHz
Bass/Treble filtering based upon in-board amplifier crossover setting (HP-LP-AP)
Controls bass on rear outputs of 4-channel amplifiers
Conveniently mount under dash, inside center console or glovebox
Includes bass knob, cable, mounting clip, mounting screws
1 Year Warranty
Cable and mounting hardware included.
Double-DIN Size Head-Unit Replacement Dash-Kit for Select BMW 3-Series Vehicles, without factory navigation
This stereo installation kit is engineered to help you install a 4" tall (Double-DIN) aftermarket radio into the original vehicle dashboard. This dash kit helps make radio replacement simple and is painted scratch-resistant matte black to match the original look and feel of the vehicle's dashboard. Minor modifications to the climate control panel are required for this installation and instructions are included. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn't offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 4" tall aftermarket radio
Painted scratch-resistant matte black
Designed for models without factory navigation
Minimal modifications to the climate control panel are necessary
To retain the factory heated seat switches, also use 98-9306
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instruction
Applications
BMW
3 Series
coupe, convertible, wagon
2012-2013
3 Series
2007-2011
3 Series
sedan, wagon
2006-2006
M3
2007-2013
Add-On Hard-Wired Power Cable For Portable Radar Detectors
The Direct Wire SmartCord is able to power your radar-detector without use of your cigarette lighter power outlet, creating a clean, simple aesthetic in your interior. Works with all current generation ESCORT windshield mounted detectors.
DIN or DDIN-Size Head-Unit Replacement Dash-Kit for Select 2006-2012 Mercedes-Benz GL and ML Vehicles
This stereo installation kit has been engineered to help you install either a 2” tall (Single-DIN) or a 4” tall (Double-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2” radio to fill the extra space in the radio opening, which can be used for storage. The pocket is not needed when installing a 4” tall radio. The dash kit is painted scratch-resistant matte black to match the original look and feel of the vehicle’s dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn’t offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2” or 4” tall aftermarket radio
Painted scratch-resistant matte black
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
MERCEDES
GL-Class
2007-2012
ML-Class
2006-2011
Metra 99-8723B Installation Manual
DIN-Size Head-Unit Replacement Dash-Kit for Select 2001-2006 Ford, Lincoln and Mercury Vehicles
This stereo installation kit has been engineered to help you install a 2” tall (Single-DIN or ISO Single-DIN) aftermarket radio into the original vehicle dashboard. This dash kit makes radio replacement simple and comes with a pocket that is installed below the 2” radio to fill the extra space in the radio opening, which can be used for storage. The dash kit is designed to match the original look and feel of the vehicle’s dashboard. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn’t offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 2” tall aftermarket radio
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes brackets and hardware parts needed with detailed installation instructions
Applications
FORD
Expedition
2003-2006
Explorer
2002-2005
Mustang
2001-2004
LINCOLN
Aviator
2003-2005
Navigator
2003-2006
MERCURY
Mountaineer
2002-2005
Metra 99-5026 Installation Manual
Amplified Head-Unit Replacement Wiring Harness Adapter for Select 1998-2003 Ford, Lincoln and Mercury Vehicles
Ford premium with RCAs and power antenna
Applications
FORD
Crown Victoria
1998-2001
Escape
2001-2003
Explorer
1998-2003
Explorer Sport Trac
2001-2003
Expedition
(Early 2003 Production Models)
1999-2003
Mustang
(Mach 460 or Mach 1000 Sound systems)
2001-2003
Thunderbird
2002-2003
Ranger
2004-2005
LINCOLN
Aviator
2003
Continental
1998-2003
LS Series
2000-2003
Navigator
1999-2003
Town Car
1998-2001
MERCURY
Grand Marquis
1998-2003
Mountaineer
1998-2003
Double-DIN Size Stereo Replacement Dash-Kit for Select 1997-2000 Dodge-Durango and Dakota Vehicles
This stereo installation kit is engineered to help you install an aftermarket 4" tall (Double-DIN) radio into the original vehicle dashboard. This dash kit helps make radio replacement simple and is textured to match the original look and feel of the vehicle's dashboard. Modifications to the factory radio bezel and sub-dash are required for this installation. A cutting template and instructions are included. Installing an aftermarket radio can upgrade the sound quality and provide additional features the original factory radio couldn't offer but requires this dash kit to make it fit.
Stereo installation kit designed to fit any standard 4" tall aftermarket radio with an ISO-mount provision
Textured to match factory dash
Modifications to the factory radio bezel and sub-dash are necessary
Unique design allows for a Double-DIN installation in a location with limited space
Made from the highest quality ABS plastic for an original factory-like fit and finish
Includes cutting template, brackets, and hardware parts needed with detailed installation instructions
Applications
DODGE
Dakota
1997-2000
Durango
1998-2000
Metra 95-6542 Installation Manual
HDMI and USB-Port With Splash-Resistant Cover and Optional Mounting-Bracket
Single piece design mounts both an HDMI and USB extension cable to your vehicle for use with your aftermarket head unit. Extension cables are each 3 feet long. The Splash-resistant cover is perfect for boats, or recreational vehicles. The optional dash-bracket provides an additional mounting surface if needed.
Head-Unit Replacement USB Adapter-Cable for Select 2012-2019 Honda, Scion, Subaru and Toyota Vehicles
Connects the factory USB port and cable to a full-size USB male connector in select Toyota vehicles.
Click Here to View Vehicle Coverage
Single 10-Inch Sealed Carpeted Subwoofer-Enclosure for Select 2010-2015 Toyota-Tacoma Access-Cab Pickups
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Fits: 2010-2015 Toyota Tacoma Access Cab Trucks
Installs between rear center seats
Mounting Depth: 8.5"
Volume: .96 cu.ft
Installation Note: Removal of the rear armrest is required along with Temporary removal of the front console which helps during installation. Does not affect rear seating.
Single 10-Inch Sealed Carpeted Subwoofer-Enclosure for Select 2009-2018 Ford F-150 & 2017-2018 F-250, F-350 and F-450 SuperCrew and Super-Cab Pickups
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Designed specifically for 2009-2018 Ford F150 Super Crew/Super Cab
Will also work in 2017 - 2018 F250/350/450 Super Crew / Super Cab
Premium Carpeted Finish
3/4" Hardwood MDF
Glued and Braced construction
CNC Grooved custom finish
Rounded edges
Silver spring loaded terminal cups
Subwoofer mounting depth: 4.5"
Box volume: 0.8 cubic feet (per chamber)
Sub Cut Out: 9.125”, Width:26”, Height: 9”, Depth: 13.25”
Specifications
Configuration: Single Sealed
Finish: Charcoal Carpeted
Width:26.00"
Height:4.63"
Depth:13.25"
Max Mounting Depth:4.50"
Gross VolumePer Sub:1.37
Net Volume Per Sub:0.92
Single 12-Inch Sealed Carpeted Subwoofer-Enclosure for Select 2002-2018 Ram Quad-Cab Pickups
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Accu-Tuned 11” single sealed subwoofer enclosure designed for optimum bass response and low-frequency reproduction which is ideal for lower profile sound quality subwoofers.
Premium Carpet Finish
OEM-Fit is designed and engineered specifically for the 2002-2018 Dodge Ram Quad Cab *2019 Legacy trucks to ensure an OEM fit without impeding the operation of the back seat.
Soft Woven Polyfill Damping Material helps create a flatter frequency response, low bass extension, and simulates a larger net volume air space.
Specially Formulated Aliphatic Wood Glue to ensure an airtight seal between all MDF parts with the second application of glue around all internal joints after final assembly.
Dimensions Sub cut out: 9.125”, mounting depth:6”, height: 7.25”, width: 32.7”, depth: 13.25”
May work with Legacy 2019 Vehicle Models
Specifications
Configuration: Single Sealed
Finish: Charcoal Carpeted
Width:32.75"
Height:7.25"
Depth:13.25"
Max Mounting Depth:6.00"
Gross VolumePer Sub:0.63
Net Volume Per Sub:0.63
Single 10-Inch Sealed Carpeted Subwoofer-Enclosure for Select 2002-2018 Ram Quad-Cab Pickups
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Accu-Tuned 10” single sealed subwoofer enclosure designed for optimum bass response and low-frequency reproduction which is ideal for lower profile sound quality subwoofers.
Premium Carpet Finish
OEM-Fit is designed and engineered specifically for the 2002-2018 Dodge Ram Quad Cab *2019 Legacy trucks to ensure an OEM fit without impeding the operation of the back seat.
Soft Woven Polyfill Damping Material helps create a flatter frequency response, low bass extension, and simulates a larger net volume air space.
Specially Formulated Aliphatic Wood Glue to ensure an airtight seal between all MDF parts with the second application of glue around all internal joints after final assembly.
Dimensions Sub cut out: 9.125”, mounting depth: 6”, height: 7.25”, width: 32.7”, depth: 13.25”
May work with Legacy 2019 Vehicle Models
Specifications
Configuration: Single Sealed
Finish: Charcoal Carpeted
Width: 32.75"
Height: 7.25"
Depth:13.25"
Max Mounting Depth: 6.00"
Gross VolumePer Sub: 0.63
Net Volume Per Sub: 0.63
Web-Programmable Remote Start Solution for Select Chrysler, Dodge, Jeep, RAM and VW Vehicles
Qty 1- Omegalink OL-RS-CH4 Chrysler/Dodge/Jeep/RAM/VW RF Style Remote Start
The OL-RS-CH4 is a web-programmable, standalone remote start solution for Chrysler ‘Tipstart’ models 2008 and up. Supports remote start from factory transmitter by pressing 3 X LOCK. Includes custom t-harness for ‘plug & play’ installation. Can be paired with compatible range-extender kit sold separately.
NOTE: This system does not have firmware loaded when new. It must be flashed by an authorized Omega Dealer before installation is possible.
Click Here to View Vehicle Coverage Information
Note: Features may vary depending on vehicle year, make, and model. Please consult your installer for more information.
Downloadable Software
Feature Selection
Advanced Feature Programming V2
Door Lock
Priority Unlock
Door Unlock
Trunk/Hatch Release
Arm OEM Alarm
Disarm OEM Alarm
Aftermarket Alarm Ctrl from OEM remotes
Horn Ctrl (wire)
Door Stat Output
Trunk Stat Output
Data Immobilizer Bypass
Parking Light Ctrl
Tachometer Output
Brake Pedal Stat Output
E-Brake Output
RAP Shutdown Ctrl
Data/MUX Keysense Ctrl
Data/MUX Accessory Ctrl
Data/MUX Ignition Ctrl
Data/MUX Starter Ctrl
3XLOCK start w/ standalone module
Qty 1 - Your choice of Extended Range Remote Control
None - 1-Way Operation with factory key fab by pressing the Lock Button 3 times. - Limited to Factory Fab Operating Range
OL-RF-15-SST - 2-Way 1-Button Add-on RF Style Remote Start Remote Control - 3000' Range
OL-RF-42-SST - 2-Way 5-Button Add-on RF Style Remote Start Remote Control - 3000' Range
CarLink - Add-on RF Style Cellular Remote Start Remote Control - 1.5 Mile Range
LINKR-LT2 - Add-on Cellular Remote Start Controller, data plan required - Cell Tower Range
Lifetime Warranty with our add-on Professional Remote Start installation.
Lifetime warranty on our un-altered installation
Lifetime warranty on the remote start and bypass system
Smartphone Controlled Remote Start System for Select Key-Turn-Start Vehicles
Qty 1 - Extreme Range CarLink 2-Way Remote From Voxx Electronics
No monthly fees
Connects via Bluetooth directly to the antenna and/or the long range remote
True 2-way communication powered by LoRa™ technology
Real-time Bluetooth® communication interaction with your smartphone with rapid response
2-way LED remote with over 1.5 miles of operating range
Micro USB rechargeable Li-On battery (cable not included)
Compatible with most digital remote start and security systems
Compatible with android & iOS Smartphones
Qty 1 - Omega Excalibur RS-170-B - Add-on Customizable Remote Start System
Activates from almost any existing keyless entry or security system
Includes status light and override switch
Remote start compatible with gas or diesel engines!
Selectable engine run times!
Low voltage & low temp auto starting
Rear defrost activation output
Turbo timer - 1, 2, or 3 minute run time!
Enhanced audible remote start diagnostics
VIRTUAL ALARM
Flashing light output.
Optional anti-grind feature to protect your starter.
Silent pit-stop operation
2 data ports -- auto-detects protocol!
RK-Kit upgrade compatible
Linkr-LT compatible
Limited Lifetime warranty on all components.
Qty 1 - Omegalink Blade Style Remote Start Bypass Module
Lifetime Warranty with our add-on Professional Remote Start installation.
Lifetime warranty on our un-altered installation
Lifetime warranty on the remote start and bypass system
Single 12-Inch Sealed Carpeted Subwoofer-Enclosure for Select 1999-2007 Chevrolet-Silverado or GMC-Sierra Extended-Cab Pickups
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Custom down fire fit under rear driver side seat. No modification required. Doesn't affect rear seat latching.
Single 12" Carpeted Finish Subwoofer Enclosure
Designed specifically for 1999-2007 Chevy Silverado and GMC Sierra Extended Cab Trucks
Premium Carpeted Finish
3/4" Mounting Baffle
Hardwood MDF construction
Rounded edges
Glued and Braced construction
Subwoofer mounting depth: 7.25"
Box volume: 0.93 cubic feet (per chamber)
Specifications
Width
24
Height
9.125
Depth
14.75
Mounting Depth
7.25
Gross Cubic Feet Per Side
0.93
Net Cubic Feet Per Side
0.93
Excursion
1.625
Dual 10-Inch Sealed Carpeted Subwoofer-Enclosure for Select 2007-2014 Chevrolet-Silverado or GMC-Sierra Extended-Cab Trucks
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Custom downfire fit under rear seat. Fits bench style, 60/40 style seats
Designed specifically for 2007-2014 Chevy Silverado and GMC Sierra Extended Cab Trucks
Dual 10" Subwoofer Enclosure
Premium Carpet Finish
3/4" Mounting Baffle
Hardwood MDF construction
Rounded edges
Glued and Braced construction
Subwoofer mounting depth: 6.25"
Box volume: 0.8 cubic feet (per chamber)
Specifications
Width
52.75
Height
6.875
Depth
11.875
Mounting Depth
6.25
Gross Cubic Feet Per Side
0.8
Net Cubic Feet Per Side
0.8
Excursion
3.625
Single 10-Inch Vented Carpeted Subwoofer-Enclosure for Select 1999-2007 Chevrolet-Silverado or GMC-Sierra Extended-Cab Trucks
CLICK HERE TO VIEW SUBWOOFERS THAT FIT THIS BOX!
Accu-Tuned 10” Single vented subwoofer enclosure designed for optimum bass response and low-frequency reproduction which is ideal for lower profile sound quality subwoofers.
OEM-Fit is designed and engineered specifically for the 1999-2007 Chevrolet / GMC trucks to ensure an OEM fit without impeding the operation of the back seat.
Specially Formulated Aliphatic Wood Glue to ensure an airtight seal between all MDF parts with a second application of glue around all internal joints after final assembly.
Pneumatic Applied Brad Nails to pull tight and hold the MDF parts during the glue drying process and help assure a no-leak, no-rattle air chamber.
Dimensions Sub Cut Out: 9.125”, Mounting Depth: 7.25”, Width: 24”, Height: 9.125”, Depth: 24”
Specifications
Width
24
Height
9.125
Depth
24
Vent Width
1.25
Vent Height
5
Vent Depth
9
Mounting Depth
7.25
Gross Cubic Feet Per Side
1
Net Cubic Feet Per Side
0.93
HZ
41
Excursion
1.625
Remote Start System for Select 2007-2018 Dodge, Frieghtliner, and Mercedes Sprinter Vehicles
Enables remote start using factory remote (Lock 3X)
Drone smart phone control can be added
Sprinter 2007-2018
Will interface with Compustar alarm/remote start (CM7000)
Please note: remote start run time for Sprinter is 1-hour unless using alarm – if a shorter run time is desired, please contact us for custom programming
Plug-and-play remote start system for Mercedes-Benz, Dodge and Freightliner Sprinter Vans.
Compatible with all variants from 2007-2018
Works with factory key fob out of the box (3X Lock)
Interfaces with Compustar alarm/remote start (CM7000), RF remotes (for extended range), as well as Compustar Drone smart phone control interface*
Seamless solution that does not disrupt integrity of the vehicle, keeping all warranties intact.
