Marine Market

MHD-Series Monoblock Class-D Marine Grade Amplifier, 750-Watts @ 1.5-4-Ohms This ultra-compact monoblock amplifier employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 750W of clean power into any impedance between 1.5 and 4Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion ultra-low and maximizes your bass performance. While targeted primarily to subwoofer applications, the MHD750/1 is a full-range amplifier and can also be used to drive high-performance mid and high frequency speaker systems. This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment. Specifications @ 4 Ω 750 W RMS x 1 @ 3 Ω 750 W RMS x 1 @ 2 Ω 750 W RMS x 1 @ 1.5 Ω 750 W RMS x 1 Frequency Response 6 Hz - 8 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >110 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W (Main Channels) >88 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >500 / 50 Hz Damping Factor @ 2 Ω >250 / 50 Hz THD+N @ Rated Power (Main Channels) <0.03% @ 4 Ω Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter 30 Hz, defeatable Bass Boost EQ (0 to +12 dB @ 45 Hz) No Output Polarity Switch Yes Remote Subwoofer Level Control Optional (HD-RLC) Pass-Through Preamp Output Buffered JL Audio MHD750/1 Manual

Read more less

XDM-Series Monoblock Class-D Marine-Grade Amplifier, 1000-Watts @ 2-Ohm or 600-Watts @ 4-Ohm This monoblock subwoofer powerhouse employs JL-Audio's high-speed NexD switching technology to achieve unprecedented efficiency and amazing power output from a very compact chassis. The XDM1000/1 generates up to 1000W of continuous power into a 2-ohm load (14.4V, 1% THD), making it a great choice to drive higher power subwoofer systems. Designed for car or boat installations, the XDM1000/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Intended specifically for subwoofer applications, the XDM1000/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500Hz and a defeatable infrasonic filter (30Hz, 24dB/oct.). With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 600 W RMS x 1 @ 14.4V @ 3 Ω 800 W RMS x 1 @ 14.4V @ 2 Ω 1000 W RMS x 1 @ 14.4V @ 1.5 Ω N/A @ 4 Ω 500 W RMS x 1 @ 12.5 V @ 3 Ω 650 W RMS x 1 @ 12.5 V @ 2 Ω 800 W RMS x 1 @ 12.5 V @ 1.5 Ω N/A Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >83 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >53 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter 30 Hz, defeatable Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Height (H) 2.05 in / 52 mm Width (W) 14.73 in / 374 mm Depth (D) 7.09 in / 180 mm JL Audio XDM1000/1v2 Manual

Read more less

XDM-Series Monoblock Class-D Marine-Grade Amplifier, 600-Watts @ 2-Ohm or 400-Watts @ 4-Ohm This potent monoblock amplifier employs JL-Audio's high-speed NexD switching design to achieve unprecedented efficiency and amazing power output from a very compact chassis. Don't let its small size fool you, though... the XDM/600/1 generates serious subwoofer power, delivering a full 600W of continuous power into a 2-ohm load (14.4V, 1% THD). Designed for car or boat installations, the XDM600/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Targeted specifically for subwoofer applications, the XDM600/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 400 W RMS x 1 @ 14.4V @ 3 Ω 500 W RMS x 1 @ 14.4V @ 2 Ω 600 W RMS x 1 @ 14.4V @ 1.5 Ω N/A @ 4 Ω 300 W RMS x 1 @ 12.5V @ 3 Ω 400 W RMS x 1 @ 12.5V @ 2 Ω 500 W RMS x 1 @ 12.5V @ 1.5 Ω N/A Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >87 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >67 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter 30 Hz, defeatable Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 6.3 lb / 2.86 kg JL Audio XDM600/1 Manual

Read more less

XDM-Series Monoblock Class-D Marine-Grade Amplifier, 300-Watts @ 2-Ohm or 200-Watts @ 4-Ohm This little monoblock powerhouse employs JL-Audio's high-speed NexD switching design to achieve unprecedented efficiency and amazing power output for its size. It is small enough to fit in most tight space applications, including small boats, pickups, motorcycles and UTV’s (in a weather-tight compartment). Designed for car or boat installations, the XDM300/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Targeted specifically for subwoofer applications, the XDM300/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Specifications @ 4 Ω 200 W RMS x 1 @ 14.4V @ 3 Ω 250 W RMS x 1 @ 14.4V @ 2 Ω 300 W RMS x 1 @ 14.4V @ 1.5 Ω N/A @ 4 Ω 160 W RMS x 1 @ 12.5V @ 3 Ω 210 W RMS x 1 @ 12.5V @ 2 Ω 270 W RMS x 1 @ 12.5V @ 1.5 Ω N/A Frequency Response 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >100 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >80 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >120 / 50 Hz Damping Factor @ 2 Ω >60 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter none Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Height (H) 2.05 in / 52 mm Width (W) 6.85 in / 174 mm Depth (D) 7.09 in / 180 mm Net Weight 3.8 lb / 1.72 kg JL Audio XDM300/1 Manual

Read more less

 MX-Series 500-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 300W @ 4-Ohm Engineered specifically for powersports applications, the MX500/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. With a robust 500W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX500/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch. Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 12 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >97 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >70 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >115 / 50 Hz Damping Factor @ 2 Ω >54 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) @ 4 Ω 300 W RMS x 1 @ 3 Ω 400 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A JL Audio MX500/1 Manual

Read more less

MX-Series 300-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 160-Watt @ 4-Ohm Engineered specifically for powersports applications, the MX300/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles. With a robust 300W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX300/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch. Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat. This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability. Specifications Frequency Response 20 Hz - 12 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω Input Voltage Range @ RCA Inputs Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) @ 4 Ω 160 W RMS x 1 @ 3 Ω 220 W RMS x 1 @ 2 Ω 300 W RMS x 1 @ 1.5 Ω N/A JL Audio MX300/1 Manual

Read more less