JD-Series Monoblock Amplifier, 500-Watt @ 2-Ohm or 250-Watt @ 4-Ohm
Designed to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the JD500/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. JL Audio's proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD500/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD500/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
General Specifications
@ 4 Ω
250 W RMS x 1
@ 3 Ω
350 W RMS x 1
@ 2 Ω
500 W RMS x 1
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass only
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
No
Filter Defeat Function
No
Infrasonic Filter
No
Bass Boost EQ
Yes
Output Polarity Switch
No
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Bass EQ Boost Control
No
Pass-Through Preamp Output
Buffered
JL Audio JD500/1 Manual
Fully Active 2-Channel Speaker Level to Line Output Converter
Designed by JL Audio Sr. Engineer Bruce Macmillan, the LoC-22 is an active two-channel processor engineered for applications requiring the attenuation of factory audio signals for use with aftermarket amplifiers and signal processors.
The LoC-22 utilizes a fully regulated, switching MOSFET power supply and an all-analog circuit design to deliver flat frequency response, at any signal level (3 Hz – 32 kHz, +0, -1dB), without altering bass response at high levels, like many passive line output converters do.
Engineered to combat induced cable noise, the LoC-22 features a differential-balanced input architecture making it compatible with virtually any analog audio signal. Capable of accepting up to 40V RMS per channel (equivalent to 400W @ 4 ohms), the LoC-22 easily handles the most powerful factory amplifier outputs. An onboard dual-range input load switch allows compatibility with most factory amplifiers that employ impedance sensing to mute channels.
Ideal for full-range or low-frequency applications, the LoC-22 is equipped with a pair of analog RCA-type, line-level output jacks (up to 8V RMS) to feed audio signals to your aftermarket system. Analog outputs are compatible with most types of aftermarket signal processors or amplifiers. Setting output levels is super simple and easy, thanks to a specially calibrated, onboard clipping indicator that works with test tones or music. The LoC-22 offers two automatic turn-on methods (DC-Offset Sensing or Signal Sensing) and provides a positive 12V turn-on output to activate aftermarket amplifiers or other downstream electronics.
The LoC-22 includes the following features:
Fully active, all analog circuit design by Bruce Macmillan, handles powerful factory amplifier outputs, up to 40 volts per channel
Differential-balanced input architecture offers noise rejection and compatibility with most analog outputs from OEM source units and amplifiers
Dual range input load switch (20 kΩ/Normal, 60 Ω/Low Z, thermally protected) for maximum compatibility with OEM amplifiers
One stereo pair of crystal-clear, line-level RCA output jacks (up to 8V RMS)
Automatic turn-on via DC-Offset or Signal-Sensing
A dedicated 12V remote turn-on output (maximum 100 mA) to activate aftermarket signal processors or amplifiers
Onboard LED clipping indicator makes output level setting quick & easy
Ultra-compact chassis design fits into just about any installation location!
Specifications
Power Supply Type
Switching, MOSFET PWM, Regulated
Operating Voltage
9 - 16 V DC
Standby Current Draw
<1.6 mA
Operating Current Draw
0.13 A at 13.8V
Frequency Response
3 Hz - 32 kHz (+0 dB, -1dB)
S/N Ratio @ 2V RMS
Gain at Min: 118 dB Gain at Max: 103 dB (20 kHz Bandwidth)
Remote Output Capacity
100 mA (maximum)
Recommended Fuse Value
1 A
Recommended Fuse Type
Fast-Acting, ATO/ATC or similar
Input Channels
Two
Input Type
Differential-Balanced
Input Voltage
40V RMS per channel (maximum)
Input Impedance
Normal: 20kΩLow Z: 60Ω
Turn-On Threshold
Signal-Sensing: 5 mV On/3.5 mV Off at1 kHz (Left Input) DC-Offset: 4.5 V
Output Channels
Two
Analog Output
Unbalanced, stereo RCA jacks
Max. Unclipped Output
8V RMS
Output Impedance
450 Ω
Gain Range
-27.3 dB (full CCW) to +3.2 dB (full CW)
THD+N
0.01% at 2V RMS (1kHz)
JL Audio LoC-22 Manual
M-Series 4-Channel Class-D Full-Range Marine-Grade Amplifier, 75-Watts x 4-Channel @ 4-Ohm
This tiny amplifier packs a serious full-range punch, delivering a staggering 100W to each of its four channels into 2Ω (14.4V, 1% THD). The breakthrough that makes this much power possible in such a small chassis is JL's NexD™ ultra-high-speed switching design, which allows for full bandwidth Class D operation with extremely low distortion and outstanding efficiency.
Use the M400/4 in combination with JL's M600/1 monoblock to build a 1000W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat. Or, use the M400/4 by itself to power two satellites, plus a subwoofer. With M-Series amplifier, the possibilities are endless.
The M400/4 includes a 12dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500Hz. With the addition of an HD-RLC remote level control (sold separately), the amplifier's Ch. 1 & 2 level or overall level can be directly controlled from a remote location.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
Specifications
@ 4 Ω
75 W RMS x 4
@ 2 Ω
100 W RMS x 4
Bridged @ 4Ω
200 W RMS x 2
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
100 mV - 4 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional (HD-RLC)
Remote Level Modes
2 or All channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes
JL Audio M400/4 Manual
Hideaway Style Weatherproof Bluetooth Receiver with Panel Mount Controller
Engineered for marine, motorsports and outdoor applications, the MBT-CRXv3 wireless receiver is designed to deliver top-quality streaming audio to almost any sound system over land or water.
Housed in a compact and water-resistant chassis (IP67-rated), this premium audio receiver is well suited for small watercraft, motorcycles, golf carts and utility vehicles. Needing just a single hole for installation, the MBT-CRXv3 wireless receiver can function as a stand-alone, wireless audio source unit or as an add-on, wireless audio controller and receiver. Large backlit controls permit easy operation day or night, and an adaptor plate is included for front-mount applications or where rear access is limited.
Outfitted with BLUETOOTH wireless technology and the Qualcomm® aptX™ HD audio codec, MBT-CRXv3 delivers dynamic, CD-like sound from your compatible streaming device from up to 35’ (11 meters) away. Two sets of stereo preamp outputs (4-volt RMS) are on hand to feed two main audio zones plus a dedicated subwoofer output. Independent audio zone level controls with LED color indicators ensure effortless command of your sound system while your streaming device is tucked away.
The receiver includes +12-volt (1 amp) remote turn-on output for amplifier control.
Specifications
Bluetooth® Core Specification
Version 5.0 with Qualcomm® aptX™-HD audio
Current Draw
83 mA (at idle) / 108 mA (at full output)
Input Operating Voltage
8 - 16 VDC
Fuse Rating
2A Mini ATC
Output Voltage
4V RMS
Frequency Response
20 Hz - 20 kHz (±1dB)
Connection Range*
Up to 35 ft / 11 m
S/N Ratio
101 dB (20 Hz - 20 kHz)
Remote Turn-on Output Capacity
350 mA (max)
Bluetooth® Profile
A2DP (High-Quality, Stereo Audio)
Outputs
Two Stereo Pairs Per Zone, Plus One Mono Subwoofer (RCA Plugs)
JL Audio MBT-CRXv2 Manual
Hideaway Style Weatherproof Bluetooth Receiver
The MBT-RXv2 wireless receiver is designed to easily add high-quality streaming audio capability to virtually any sound system.
Equipped with BLUETOOTH wireless technology and the Qualcomm® aptX™ HD audio codec, the MBT-RXv2 wireless receiver sends top-quality sound directly to any amplifier or source unit with line-level inputs via a pair of crystal-clear preamp outputs (4-volt RMS).
Housed in a sealed and water-resistant (IPX7-rated) chassis, this premium audio receiver is ideally suited for challenging outdoor applications, plus its tiny design can easily fit in almost any installation location. A simple procedure is all it takes to pair MBT-RXv2 to your device, with automatic reconnection afterward. All playback, including volume and media selection, is controlled by using your compatible streaming device from up to 35’ (11 meters) away.
The receiver includes +12-volt (1 amp) remote turn-on output for amplifier control.
Specifications
Bluetooth® Profile
A2DP (High-Quality, Stereo Audio)
Bluetooth® Core Specification
Version 5.0 with Qualcomm® aptX™-HD audio
Frequency Response
20 Hz - 20 kHz (±1dB)
Outputs
One Stereo Pair, Low-Level RCA Plugs
Output Voltage
4V RMS
S/N Ratio
100 dB (20 Hz - 20 kHz)
Input Operating Voltage
10 - 16 VDC
Current Draw
40 mA
Fuse Rating
2 A Mini ATC
Connection Range*
Up to 35' / 11 m
JL Audio MBT-RX Manual
Water-Resistant Remote Bass-Knob for Select JL Audio Amplifiers
The MHD-RLC remotely controls the Bass Level of the following JL Audio amplifiers:
HD-Series: All models
XD-Series: All models
MHD-Series: All models
M-Series: All models
When the MHD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.
The MHD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 16.4 ft. (5 m) cable.
A satin-finish aluminum knob can be purchased separately.
MHD-Series 4-Channel Class-D Marine Grade Amplifier, 150-Watts x 4ch @ 1.5-4-Ohms
This compact, multi-channel powerhouse employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 150W x 4ch or 300W x 2ch. Tight power supply regulation keeps distortion down and maximizes sound quality.
When using the MHD750/1 to drive a subwoofer system, the MHD600/4 is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. It can also be deployed, on its own, as a very capable 3-channel system amplifier with 150W x 2 to the satellites and 300W x 1 to a subwoofer system.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
Specifications
@ 4 Ω
150 W RMS x 4
@ 3 Ω
150 W RMS x 4
@ 2 Ω
150 W RMS x 4
@ 1.5 Ω
150 W RMS x 4
Bridged @ 8 Ω
300 W RMS x 2
Bridged @ 4 Ω
300 W RMS x 2
Frequency Response
6 Hz - 30 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>110 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>88.2 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>300 / 50 Hz
Damping Factor @ 2 Ω
>150 / 50 Hz
THD+N @ Rated Power
<0.03% @ 4 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS to 800 mV - 8 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional (HD-RLC)
Remote Level Modes
2 or All Channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes
JL Audio MHD600/4 Manual
MHD-Series 4-Channel Class-D 24-Volt Marine Grade Amplifier, 150-Watts x 4ch @ 1.5-4-Ohms
This compact, multi-channel powerhouse employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 150W x 4ch or 300W x 2ch's. Tight power supply regulation keeps distortion down and maximizes sound quality.
The MHD600/4-24V is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. It can also be deployed, on its own, as a very capable 3-channel system amplifier with 150W x 2ch to the satellites and 300W x 1 to a subwoofer system.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24 V may result in damage to the product and will void the warranty.
Specifications
@ 4 Ω
150 W RMS x 4
@ 3 Ω
150 W RMS x 4
@ 2 Ω
150 W RMS x 4
@ 1.5 Ω
150 W RMS x 4
Bridged @ 8 Ω
300 W RMS x 2
Bridged @ 4 Ω
300 W RMS x 2
Frequency Response
6 Hz - 30 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>110 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>88.2 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>300 / 50 Hz
Damping Factor @ 2 Ω
>150 / 50 Hz
THD+N @ Rated Power
<0.03% @ 4 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS to 800 mV - 8 V RMS
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
25 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Remote Level Control
Optional (HD-RLC)
Remote Level Modes
2 or All Channels
Channel Input Mode Switch
Yes (2/4 ch.)
Pass-Through Preamp Output
Buffered
Source Channel Selection for PreOuts
Yes
JL Audio MHD600/4-24V Manual
MHD-Series Monoblock Class-D Marine Grade Amplifier, 750-Watts @ 1.5-4-Ohms
This ultra-compact monoblock amplifier employs JL's Single-Cycle Control switching design and R.I.P.S. technology to deliver 750W of clean power into any impedance between 1.5 and 4Ω, giving you the highest degree of flexibility in designing your subwoofer system.
Tight power supply regulation keeps distortion ultra-low and maximizes your bass performance. While targeted primarily to subwoofer applications, the MHD750/1 is a full-range amplifier and can also be used to drive high-performance mid and high frequency speaker systems.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
Specifications
@ 4 Ω
750 W RMS x 1
@ 3 Ω
750 W RMS x 1
@ 2 Ω
750 W RMS x 1
@ 1.5 Ω
750 W RMS x 1
Frequency Response
6 Hz - 8 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>110 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Main Channels)
>88 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>500 / 50 Hz
Damping Factor @ 2 Ω
>250 / 50 Hz
THD+N @ Rated Power (Main Channels)
<0.03% @ 4 Ω
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Filter Mode(s)
Low-Pass or High-Pass
Filter Slope(s)
12/24 dB/octave
Filter Frequency Range
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Infrasonic Filter
30 Hz, defeatable
Bass Boost EQ (0 to +12 dB @ 45 Hz)
No
Output Polarity Switch
Yes
Remote Subwoofer Level Control
Optional (HD-RLC)
Pass-Through Preamp Output
Buffered
JL Audio MHD750/1 Manual
MHD-Series 5-Channel Class-D Marine Grade Amplifier, 100-Watts x 4ch + 500-Watt Mono @ 1.5-4Ω
Thanks to its ability to act as a "one-box solution", the MHD900/5 is ideal for installations where space is at a premium and sound quality is the paramount goal.
While extremely compact, this amazing amplifier will comfortably drive a complete high-performance marine audio system: that is, four satellite speaker systems and a subwoofer system... with a very serious 900 watts of power!
Using JL Audio's Single Cycle Control switching design and R.I.P.S technology, the MHD900/5 delivers 100W x 4ch, plus a very meaty 500W to its subwoofer channel. Thanks to R.I.P.S., high power can be delivered over a wide range of load impedances, while the tight power supply regulation keeps distortion down, maximizing sound quality.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
Specifications
Main Channels @ 4 Ω
100 W RMS x 4
Main Channels @ 3 Ω
75 W RMS x 4
Main Channels @ 2 Ω
75 W RMS x 4
Main Channels @ 1.5 Ω
75 W RMS x 4
Main Channels - Bridged @ 8 Ω
200 W RMS x 2
Main Channels - Bridged @ 4 Ω
150 W RMS x 2
Subwoofer Channel @ 4 Ω
500 W RMS x 1
Subwoofer Channel @ 3 Ω
500 W RMS x 1
Subwoofer Channel @ 2 Ω
500 W RMS x 1
Subwoofer Channel @ 1.5 Ω
500 W RMS x 1
Frequency Response (Main Channels)
12 Hz - 28 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
12 Hz - 10 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>108.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Main Channels)
>88.2 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>400 / 50 Hz
Damping Factor @ 2 Ω
>200 / 50 Hz
THD+N @ Rated Power (Main Channels)
<0.03% @ 4 Ω
THD+N @ Rated Power (Subwoofer Channel)
<0.05% @ 4 Ω
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
Accepts up to 4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Filter Mode(s): Channels 1 & 2 (front)
High-Pass only
Filter Slope(s): Channels 1 & 2 (front)
12/24 dB/octave
Filter Frequency Range: Channels 1 & 2 (front)
50 Hz - 500 Hz
Filter Mode(s): Channels 3 & 4 (rear)
High-Pass only
Filter Slope(s): Channels 3 & 4 (rear)
12/24 dB/octave
Filter Frequency Range: Channels 3 & 4
50 Hz - 500 Hz
Filter Mode(s): Subwoofer Channel
Low-Pass only
Filter Slope(s): Subwoofer Channel
12/24 dB/octave
Filter Frequency Range: Subwoofer Channel
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Infrasonic Filter: Subwoofer Channel
30 Hz, Defeatable
Remote Level Control
Optional (HD-RLC)
Remote Level Modes
Sub Ch. only
Channel Input Mode Switch
Yes (2/4/6 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
JL Audio MHD900/5 Manual
MHD-Series 5-Channel Class-D 24-Volt Marine Grade Amplifier, 100-Watts x 4ch + 500-Watt Mono @ 1.5-4Ω
Thanks to its ability to act as a "one-box solution", the MHD900/5-24V is ideal for installations where space is at a premium and sound quality is the paramount goal.
While extremely compact, this amazing amplifier will comfortably drive a complete high-performance marine audio system: that is, four satellite speaker systems and a subwoofer system... with a very serious 900 watts of power!
Using JL Audio's Single Cycle Control switching design and R.I.P.S technology, the MHD900/5-24V delivers 100W x 4ch to its four main channels, plus a very meaty 500W to its subwoofer channel. Thanks to R.I.P.S., high power can be delivered over a wide range of load impedances, while the tight power supply regulation keeps distortion down, maximizing sound quality.
This marine amplifier features white and gray powder-coat finishes, a gasketed cover for the controls and stainless steel hardware for durability in the marine environment.
This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24V may result in damage to the product and will void the warranty.
Specifications
Main Channels @ 4 Ω
100 W RMS x 4
Main Channels @ 3 Ω
75 W RMS x 4
Main Channels @ 2 Ω
75 W RMS x 4
Main Channels @ 1.5 Ω
75 W RMS x 4
Main Channels - Bridged @ 8 Ω
200 W RMS x 2
Main Channels - Bridged @ 4 Ω
150 W RMS x 2
Subwoofer Channel @ 4 Ω
500 W RMS x 1
Subwoofer Channel @ 3 Ω
500 W RMS x 1
Subwoofer Channel @ 2 Ω
500 W RMS x 1
Subwoofer Channel @ 1.5 Ω
500 W RMS x 1
Frequency Response (Main Channels)
12 Hz - 28 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
12 Hz - 10 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>108.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W (Main Channels)
>88.2 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>400 / 50 Hz
Damping Factor @ 2 Ω
>200 / 50 Hz
THD+N @ Rated Power (Main Channels)
<0.03% @ 4 Ω
THD+N @ Rated Power (Subwoofer Channel)
<0.05% @ 4 Ω
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
Accepts up to 4 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
Filter Mode(s): Channels 1 & 2 (front)
High-Pass only
Filter Slope(s): Channels 1 & 2 (front)
12/24 dB/octave
Filter Frequency Range: Channels 1 & 2 (front)
50 Hz - 500 Hz
Filter Mode(s): Channels 3 & 4 (rear)
High-Pass only
Filter Slope(s): Channels 3 & 4 (rear)
12/24 dB/octave
Filter Frequency Range: Channels 3 & 4
50 Hz - 500 Hz
Filter Mode(s): Subwoofer Channel
Low-Pass only
Filter Slope(s): Subwoofer Channel
12/24 dB/octave
Filter Frequency Range: Subwoofer Channel
50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometers
Yes
Filter Defeat Function
Yes
Infrasonic Filter: Subwoofer Channel
30 Hz, Defeatable
Remote Level Control
Optional (HD-RLC)
Remote Level Modes
Sub Ch. only
Channel Input Mode Switch
Yes (2/4/6 ch.)
Pass-Through Preamp Output
None
Source Channel Selection for PreOuts
N/A
JL Audio MHD900/5-24V Manual
MediaMaster-Series Add-on Marine 2.3-Inch Remote Controller
The MMR-20-BE is a wired remote controller engineered to add auxiliary control functionality to MediaMaster® source units.
Built for marine and off-road applications, its weatherproof (IP67 rated) design places frequently used functions of your MediaMaster® source unit in a simple, intuitive design that’s easy-to-use. Its large, backlit controls and LED source indicators are easily identifiable, day or night, with brightness settings that can be adjusted using your MediaMaster® source unit.
A small footprint and simple, one-hole design means the MMR-20-BE can be installed in even the tightest of spaces. Depending on your system layout, you may add up to three MMR-20-BE remote controllers to a single MediaMaster® source unit. Each MMR-20 can be connected up to 75 ft. (22.8 m) away from its source unit.
MediaMaster® remote control capabilities include:
Power On/Off
Source Select
Volume Up/Down
Track Up/Down (USB & BT)
Track Fast-Forward/Fast-Rewind (USB)
Favorite Up/Down (Radio)
Play/Pause (USB & BT)
Mute/Unmute (Radio & Aux)
The MMR-20-BE is compatible with these MediaMaster® source units:
MM100s-BE
MM100s
MM50
Note: Requires MMC Connection Cables (sold separately). Connection cables are available in several lengths to fit your specific application. Y-splitters are also available to connect up to three remotes to a MediaMaster® source unit.
JL Audio MMR-20-BE Manual
MediaMaster-Series Add-on Marine Network Zone Controller with 2.8-Inch Screen
The MMR-40 is a NMEA 2000® Network Controller engineered to add full-function, auxiliary control to MediaMaster® source units.
Outfitted with a NMEA 2000® Micro-C connector, the MMR-40 connects to a host MediaMaster® source unit in two ways:
Direct interface with a vessel's NMEA 2000® network using applicable NMEA 2000® cables and connectors (not included)
Direct connection of one MMR-40 with one host MediaMaster® source unit using MMC-PN2K powered network cables (sold separately) to simulate an isolated, stand-alone NMEA 2000® network
Once connected, the MMR-40 automatically recognizes the host MediaMaster® source unit and will then mirror all host source unit controls and screen info onto the MMR-40's full-color, 2.8-inch LCD display, resulting in a complete MediaMaster® user experience.
The MMR-40 is equipped with independent display theme and lighting controls for maximum mounting location flexibility, regardless of the settings on the host source unit. Engineered for real-world marine (and many outdoor) applications, its weatherproof (IP66 rated) chassis is built to withstand the harshest environments.
The MMR-40 includes the following features:
NMEA 2000® Certified (LEN 4)
Easy-to-read, high-brightness, 2.8-inch full-color LCD display with large backlit controls
Independent day/night display themes and lighting controls
IP66 rated for real marine duty
Protective Sun Cover included
Note: The MMR-40 is not a stand-alone receiver and does not function without a connected MediaMaster® source unit. All remote control functionality of the MMR-40 is solely derived from the host source unit. Functionality of the MMR-40 requires connection to a NMEA 2000® network or use of MMC-PN2K powered network cables (sold separately).
JL Audio MMR-40 Manual
MX-Series 4-Channel Class-D Marine-Grade Amplifier, 70-Watts x 4ch @ 2-Ohm or 50-Watts x 4ch @ 4-Ohm
Engineered specifically for powersports applications, the 4-channel MX280/4 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 50W x 4 into 4 ohms (14.4V, 1% THD), the MX280/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 140W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>89.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>60 / 50 Hz
Damping Factor @ 2 Ω
>30 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
35 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
50 W RMS x 4
@ 2 Ω
70 W RMS x 4
Bridged @ 4Ω
140 W RMS x 2
JL Audio MX280/4 Manual
MX-Series 300-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 160-Watt @ 4-Ohm
Engineered specifically for powersports applications, the MX300/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 300W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX300/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 12 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
8 AWG wire
Fuse Rating
30 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
160 W RMS x 1
@ 3 Ω
220 W RMS x 1
@ 2 Ω
300 W RMS x 1
@ 1.5 Ω
N/A
JL Audio MX300/1 Manual
MX-Series 500-Watt Monoblock Marine-Grade Amplifier @ 2-Ohm or 300W @ 4-Ohm
Engineered specifically for powersports applications, the MX500/1 monoblock amplifier employs JL's high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 500W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX500/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 12 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>97 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>70 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>115 / 50 Hz
Damping Factor @ 2 Ω
>54 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
300 W RMS x 1
@ 3 Ω
400 W RMS x 1
@ 2 Ω
500 W RMS x 1
@ 1.5 Ω
N/A
JL Audio MX500/1 Manual
MX-Series 4-Channel Marine-Grade Amplifier, 125-Watts x 4ch @ 2-Ohm or 70-Watts x 4ch @ 4-Ohm
Engineered specifically for powersports applications, the 4-channel MX500/4 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 70W x 4 into 4 ohms (14.4V, 1% THD), the MX500/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 250W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>70.5 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>92 / 50 Hz
Damping Factor @ 2 Ω
>43 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
70 W RMS x 4
@ 2 Ω
125 W RMS x 4
Bridged @ 4Ω
250 W RMS x 2
JL Audio MX500/4 Manual
MX-Series 75-Watts x 2-Channel Class-D Marine-Grade Amplifier + 400-Watt Subwoofer Out @ 2-Ohm
Engineered specifically for powersports applications, the 3-channel MX600/3 amplifier employs JL's high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 75W x 2 into 4 ohms (14.4V, 1% THD), the MX600/3 is the perfect solution for driving a pair of speakers and a subwoofer.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
This amplifier features a black powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.
Specifications
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>92 / 50 Hz
Damping Factor @ 2 Ω
>43 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 580 mV - 14 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Main Channels @ 4 Ω
75 W RMS x 2
Main Channels @ 2 Ω
100 W RMS x 2
Main Channels - Bridged @ 4Ω
200 W RMS x 1
Subwoofer Channel @ 4 Ω
250 W RMS x 1
Subwoofer Channel @ 3 Ω
300 W RMS x 1
Subwoofer Channel @ 2 Ω
400 W RMS x 1
Subwoofer Channel @ 1.5 Ω
N/A
JL Audio MX600/3 Manual
RBC-Series Remote Bass Control Knob for Select JL Amplifiers
The RBC-1 remotely controls the Bass Level of the following JL Audio amplifiers:
JD-Series: JD250/1, JD500/1, JD1000/1
JX-Series: JX250/1, JX250/1D, JX500/1, JX500/1D, JX1000/1D
HX-Series: HX300/1 in Low Pass Mode (Note: M-RBC-1 is also available)
MHX-Series: MHX300/1 in Low Pass Mode (Note: M-RBC-1 is also available)
MX-Series: MX300/1, MX500/1 in Low Pass Mode (Note: M-RBC-1 is also available)
RD-Series: RD500/1, RD1000/1, RD1500/1, RD900/5
When the RBC-1 is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.
The RBC-1 remotely controls the Bass Level of the following JL Audio subwoofer systems:
PowerWedge+: All ModelsMicroSub+: All Models
When the RBC-1 is connected to the above subwoofer systems, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.
The RBC-1 remotely controls the Bass EQ boost feature of the following JL Audio amplifiers:
Slash v3 Series: 600/1v3, 1200/1v3
Slash v2 Series: 250/1v2, 500/1v2, 1000/1v2, 450/4v2
Original Slash Series: 500/1, 1000/1, 450/4, 500/5
G-Series: All Models
A-Series: All Models
e-Series: All Models (including marine versions)
M-Series: M1400, M1700, M2150, M2250, M4300, M4500, M6450, M6600
When the RBC-1 is connected to the above amplifiers, the on-board "Boost" control of the amplifier is defeated and the RBC-1 becomes the active controller.
The RBC-1 kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable.
JL Audio RBC-1 Manual
RD-Series 1000-Watt Monoblock Subwoofer Amplifier @ 2-Ohms
Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion.
For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The RD1000/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).
Specifications
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
600 W RMS x 1
@ 3 Ω
800 W RMS x 1
@ 2 Ω
1000 W RMS x 1
@ 1.5 Ω
N/A
JL Audio RD1000/1 Manual
RD-Series 1500-Watt Monoblock Class-D Subwoofer Amplifier @ 2-Ohms
Engineered for high-power, subwoofer applications, the RD1500/1 monoblock amplifier is built to deliver staggering amounts of world-class bass output. Equipped with a special low impedance circuit, the RD1500/1 is capable of generating a whopping 1500 watts of output power, at either 1 or 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion.
For your convenience, all of the RD1500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The RD1500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).
Specifications
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>82 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1100 / 50 Hz
Damping Factor @ 2 Ω
>550 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
2 AWG wire
Fuse Rating
150A (AFS or AGU)
@ 4 Ω
750 W RMS x 1
@ 3 Ω
1000 W RMS x 1
@ 2 Ω
1500 W RMS x 1
@ 1 Ω
1500 W RMS x 1
JL Audio RD1500/1 Manual
RD-Series 75-Watts x 4-Channel Automotive Amplifier @ 4-Ohms
Utilizing JL Audio's exclusive NexD™ high-speed switching technologies, the ultra-compact RD400/4 amplifier is engineered to deliver loads of audio output power, with incredible efficiency and low distortion. Don’t let its modern styling and small size fool you though, this little powerhouse churns out 100 watts of crystal-clear audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms.
For your convenience, the RD400/4’s controls can be found on top of the amplifier, beneath a protective cover, with all connections located along one side of its chassis. Studio-grade signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment, along with all-new input type switches for bridging of stereo output channels without needing to use Y-adaptors.
Onboard LED-clipping indicators are also included with your RD400/4. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. You’ll also find a set of preamp outputs on-hand, so you can pass signals to another amplifier, almost effortlessly. The RD400/4 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition.
Specifications
Frequency Response
12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
40 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
75 W RMS x 4
@ 2 Ω
100 W RMS x 4
Bridged @ 4Ω
200 W RMS x 2
JL Audio RD400/4 Manual
RD-Series 500-Watt Monoblock Subwoofer Amplifier @ 2-Ohms
Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is JL's proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion.
For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat.
Specifications
Frequency Response
7 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power
>80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>1000 / 50 Hz
Damping Factor @ 2 Ω
>500 / 50 Hz
THD+N @ Rated Power
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
50 A (AFS, AGU or MaxiFuse™)
@ 4 Ω
250 W RMS x 1
@ 3 Ω
350 W RMS x 1
@ 2 Ω
500 W RMS x 1
@ 1.5 Ω
N/A
JL Audio RD500/1 Manual
RD-Series 5-Channel Automotive Amplifier, 70-Watts x 4ch + 500-Watt Mono @ 2-Ohm
Crafted as an all-in-one, total system solution, the RD900/5 is engineered to power a complete audio system consisting of a subwoofer + four satellite system with 900 watts of high-performance sound. Equipped with JL's exclusive NexD™ switching technology, this complete power package efficiently generates a potent 70 watts of crystal-clear audio into 4 ohms, plus a robust 500 watts for a subwoofer system, all from a single compact chassis. Each pair of main channels is also fully bridgeable, stoutly producing 200 watts of full-range audio bliss (into 4 ohms), creating an ultra-powerful 3-channel amplifier.
Conveniently located on top of the RD900/5, you’ll find a complement of studio-grade signal processing features, all hidden beneath a removable protective cover. Each pair of main channels is equipped with a 12 dB / octave high-pass filter, with a dedicated low-pass filter for its subwoofer channel. All three crossovers offer continuously variable frequency selection from 50-500 Hz, for precise filtering. Dual-range, differential-balanced inputs are also onboard, capable of accepting most input voltage levels, plus automatic turn-on capability (via signal sensing or DC-offset sensing) for maximum versatility.
LED clipping indicators are also standard equipment for each channel section. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. The RD900/5 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of an RBC-1 remote level control (sold separately), you can conveniently control the subwoofer’s output remotely from the driver’s seat.
Specifications
Frequency Response (Main Channels)
12 Hz - 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel)
10 Hz - 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels)
>104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω
>150 / 50 Hz
Damping Factor @ 2 Ω
>75 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs
Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge
4 AWG wire
Fuse Rating
80 A (AFS, AGU or MaxiFuse™)
Main Channels @ 4 Ω
70 W RMS x 4
Main Channels @ 2 Ω
100 W RMS x 4
Main Channels - Bridged @ 4Ω
200 W RMS x 2
Subwoofer Channel @ 4 Ω
225 W RMS x 1
Subwoofer Channel @ 3 Ω
325 W RMS x 1
Subwoofer Channel @ 2 Ω
500 W RMS x 1
Subwoofer Channel @ 1.5 Ω
N/A
JL Audio RD900/5 Manual
Dual 12-Inch 2-Ohm 800-Watt Subwoofer-Enclosure for Select 2019-UP RAM-1500 Crew-Cab Models with Fixed Rear-Seat
This generation of RAM’s big hauler combines a bold new design with major advancements in aerodynamics, technology and towing capabilities. Unfortunately, the factory sound systems are greatly deficient in the bass reproduction department.
Fortunately, JL's engineers tackled this challenge head on and developed a subwoofer solution that fills your Crew Cab with stunning amounts of deep bass output. Featuring a 100% fiberglass, sealed enclosure design, this Stealthbox® houses two of JL Audio's revolutionary 12TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort. Rear seat folding is unaffected, and we even left space on the enclosure that’s perfect for a clean, hidden amplifier installation!
Specifications
The Hard Data: Contains two 12TW3-D8 Subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Fits 1500 Crew Cab with fixed (non- reclining) rear seat. Will not fit 2500 or 3500 models.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-5GRAMCCF/12TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Subwoofer-Enclosure for Select 2019-UP RAM-1500 Crew-Cab Trucks, with Reclining Rear-Seat
This generation of RAM’s big hauler combines a bold new design with major advancements in aerodynamics, technology and towing capabilities. Sadly, the spacious interior leaves little room for a high-performance subwoofer enclosure.
Fortunately, JL's engineers welcomed this challenge head on and developed a subwoofer solution that fills your Crew Cab with loads of deep bass output. Featuring an all-fiberglass, sealed enclosure design, this Stealthbox® houses two of JL Audio's revolutionary 10TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort. Rear seat folding and recline are unaffected, and we even left a spot on the enclosure that’s perfect for a clean, hidden amplifier installation!
Specifications
Contains two 10TW3-D8 Subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installation requires removal of under-seat storage divider panel, if equipped. Fits 1500 Crew Cab with reclining rear seat. Will not fit 2500 or 3500 models.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-5GRAMCCR/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Subwoofer-Enclosure for Select 2020-UP RAM 1500 Quad-Cab Vehicles
This generation of RAM’s big hauler combines a bold new design with major advancements in aerodynamics, technology and towing capabilities. Disappointingly, the original equipment audio systems lack the low-frequency output and performance you might expect.
Luckily, JL-Audio engineers are experts in maximizing bass from minimal space and developed a subwoofer solution that fills your Quad Cab with loads of powerful bass output. Featuring a 100% fiberglass, sealed enclosure design, this Stealthbox houses two of JL-Audio's innovative 10TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort or folding. Theyeven left space on the enclosure that’s perfect for a small, hidden amplifier installation!
The Hard Data: Contains two 10TW3-D8 Subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installation requires removal of rear underseat storage tray, if equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-5GRAMQC/10TW3 Manual
Single 12-Inch 2-Ohm 500-Watt Subwoofer-Enclosure for Select 2009-UP Dodge-Challenger
This reborn American legend just might be the most faithful interpretation of the classic “muscle car” formula to date. It has it all... raw power, aggressive looks, a comfortable interior... but, it certainly could use a serious audio system upgrade to erase the wimpy performance of the factory system.
JL's Stealthbox® for the Challenger is the perfect product to begin your audio transformation. It installs neatly into the driver-side corner of the trunk with minimal impact on usable cargo area. Spectacular sound quality and impressive output are delivered by a high-performance JL Audio 12-inch subwoofer in a sealed enclosure precisely matched to the Challenger's acoustics by our engineering team.
Great audio in your Challenger begins here.
The Hard Data: Contains one 12W3v3-2 subwoofer in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Installs against driver-side wheel well. Stealthbox® includes a steel-mesh grille to protect the driver. Access to the spare tire, jack and tools remains unaffected. Installation requires removal of factory-installed ‘subwoofer' if vehicle is equipped with ‘Kicker® SRT® Audio Package'.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-CHLGR/12W3v3 Installation Manual
Single 10-Inch 500-Watt 2-Ohm Carpeted Fiberglass Subwoofer-Enclosure for Select 2002-2018 Dodge Ram 1500 Quad Cab, 2003-Up 2500 & 3500 Quad Cab & 2009-2018 1500 Crew Cab & 2009-Up 2500 & 3500 Crew Cab Trucks
Dodge's big hauler combines large sedan passenger comfort with tough pickup truck capabilities.
JL's Stealthbox® for the Quad Cab tucks under the rear seat on the passenger side and encloses a 10-inch driver for impressive sub-bass performance. Seat folding is unaffected and plenty of room is left on the driver side for amplifier installation or storage. Best of all, the Stealthbox® is essentially invisible once installed.
The Hard Data: Contains one 10W3v3-2 in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Installs under passenger side rear-bench seat. The seat folding function remains unaffected. Cup holders are not affected. Some models require removal of the passenger side metal floor extension located under the rear seat. Some models may require cutting and removal of the underseat carpet and/or carpet padding. Will not fit Mega Cab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-QDRAM/10W3v3 Installation Manual
Dual 10-Inch 600-Watt 2-Ohm Carpeted Fiberglass Subwoofer-Enclosure for Select 2002-2018 Dodge Ram 1500 Quad Cab, 2003-Up 2500 & 3500 Quad Cab & 2009-2018 1500 Crew Cab & 2009-Up 2500 & 3500 Crew Cab Trucks
Dodge’s big hauler combines large sedan passenger comfort with tough pickup truck capabilities, but does not have a lot of extra interior space for a bulky subwoofer enclosure.
JL's Stealthbox® for the Quad Cab® neatly negotiates these challenges and tucks under the rear seat, enclosing dual 10-inch thin line subwoofer drivers for impressive sub-bass performance. Seat folding and comfort are unaffected, and plenty of room is left in the center for amplifier installation or storage. Best of all, this Stealthbox® is essentially invisible once installed, but certainly noticeable when you fire up your favorite music and experience world-class sub-bass.
The Hard Data:Contains two 10TW1-4 subwoofer drivers in a sealed enclosure. 600 watt power handling. Wired for 2 ohm mono. Some models may require cutting and removal of the underseat carpet and/or carpet padding. Will not fit Standard Cab, '02-'08 Crew Cab, or Mega Cab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-D-QDRAMD/10TW1 Installation Manual
Dual 12-Inch 800-Watt 2-Ohm Carpeted Fiberglass Subwoofer-Enclosure for Select 2009-Up Ford F-150 SuperCrew, 2017-Up SuperDuty Crew Cab Trucks
The Ford F-150 is an American icon with impressive hauling capabilities and a spacious interior, especially in SuperCrew configurations. Unfortunately, Ford’s factory sound systems leave a lot to be desired in the low frequency department.
JL's Stealthbox® for F-150 SuperCrew and SuperDuty Crew Cab trucks fills your truck with stunning sub bass output and quality, with no intrusion on cab space. Featuring an all-fiberglass, sealed enclosure design, this Stealthbox® houses two of JL Audio's revolutionary 12TW3 thin-line subwoofers and installs neatly under the rear seat, without compromising rear seat comfort.
The Hard Data: Contains two 12TW3-D8 subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installs under rear bench seat and requires removal of under-seat storage tray, if so equipped. Installation requires removal of OEM “subwoofer”, if so equipped. Does not affect folding or reclining of seat.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-150-SCDBL/12TW3 Installation Manual
Single 300-Watt 2-Ohm Thin 10-Inch Stealthbox Subwoofer-Enclosure for Select 2018-Up Ford Expedition Vehicles, with OEM Subwoofer
Ford's full-sized SUV delivers first-rate comfort with outstanding gear-hauling capability and towing capacity. This is why JL's Stealthbox solution is designed to retain 100% of your cargo space, while delivering first-class bass performance.
This model replaces the stock subwoofer and installs discreetly behind the factory cargo area trim to protect and hide its 10-inch subwoofer.
The Hard Data: Contains one 10TW1-2 subwoofer in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs behind driver side panel in the cargo area. Requires removal of the OEM "subwoofer".
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-EXPED4G/10TW1 Installation Manual
Single 400-Watt 2-Ohm 10-Inch Stealthbox Subwoofer Enclosure for Select 2015-UP Ford F-150 SuperCab and 2017-UP SuperDuty SuperCab Trucks
Benefitting from JL's revolutionary thin-woofer technology, this Stealthbox® for F-150 SuperCab and SuperDuty SuperCab trucks is designed to install neatly under the rear seat with no intrusion on cab space.
Featuring an all-fiberglass, sealed enclosure design, JL's Stealthbox® houses a 10-inch TW3 thin-line subwoofer and fills your truck with loads of deep bass output. Seat folding and reclining are unaffected, and JL even incorporated a recess on the Stealthbox’s top for mounting an amplifier, if desired.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under rear bench seat and requires removal of the storage divider panel. Stealthbox® includes a steel-mesh grille to protect the driver. Does not affect folding or reclining of seat.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-F150SPRCB/10TW3 Installation Manual
Single 400-Watt 2-Ohm Thin 12-Inch Subwoofer-Enclosure for Select 2015-UP Ford Mustang-Coupe Vehicles
The latest all-American pony car gets a big dose of horsepower and major technology enhancements, all packaged in a new sleek and sexy body. Sadly though, the stock audio systems just can't deliver enough bass to keep up with the Mustang's high-performance muscle.
JL's Stealthbox® features an all-fiberglass, sealed enclosure design that fits in the same location as the optional factory subwoofer (and requires no holes to be drilled for installation). Equipped with their revolutionary 12TW3 thin-line subwoofer, this Stealthbox delivers deep, powerful bass that's worthy of your Mustang's heritage.
The Hard Data: Contains one 12TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs in the passenger side rear corner of the trunk. Factory subwoofer (if equipped) must be removed for installation of Stealthbox®. Installation in Mustang Shelby GT350 models requires relocation of additional OEM equipment. Will not fit convertible models!
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-MUSCPE/12TW3 Installation Manual
Single 10-Inch 2-Ohm 300-Watt Subwoofer-Enclosure for Select 2019-UP Ford-Ranger SuperCrew Vehicles
Ford's mid-sized pickup promises practical utility and performance for everyday commutes or rugged terrains. To make every drive even more enjoyable, JL-Audio's Stealthbox solution tucks under the rear seat on the passenger side and encloses a 10-inch driver for impressive sub-bass performance. Seat folding is unaffected with plenty of room remaining on the driver side for storage. Best of all, the Stealthbox virtually disappears once installed.
The Hard Data: Contains one 10TW1-2 subwoofer in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Installs under passenger side rear seat in place of storage compartment. Will not fit SuperCab.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-RNGSCG4/10TW1 Manual
Single 600-Watt 2-Ohm Thin 13-Inch Subwoofer-Enclosure for Select 2004-2016 Ford SuperDuty Crew-Cab Trucks with FlexFold 60/40 Split-Bench Rear-Seat
Ford's big trucks were designed to haul people and serious payloads with ease. They also present a tough challenge for a conventional subwoofer solution due to a severe shortage of unused space in the cab. It's a good thing JL didn't let convention get in the way of creating outstanding sub-bass.
JL Audio now offers two clever Stealthbox® solutions for Ford's biggest hauler: one that installs inside the center console and this one: a super-thin, all fiberglass enclosure loaded with JL's revolutionary 13TW5v2 subwoofer and designed to install under the rear bench seat. So, if your console space is non-negotiable, you can still get world-class sub-bass that remains invisible and doesn't compromise your truck's people space.
Whether your miles pile up towing a boat or using your truck for work, you can now enjoy every one of them with one of our Stealthbox® solutions.
The Hard Data: Contains one 13TW5v2-2 subwoofer in a sealed enclosure. 600 watt power handling. Wired for 2 ohm mono. Installs under driver side of rear bench seat. Does not affect folding or reclining of seat.
Please Note: “Black (leather)”, as indicated in the chart below is the OEM color/material. The Stealthbox® model that matches that OEM color is carpeted
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-SUPRCC/13TW5v2 Installation Manual
Single 500-Watt 2-Ohm 10-Inch Subwoofer-Enclosure for Select 1998-2007 Ford-Excursion and F-Series SuperDuty Trucks with Front Bucket-Seats
If you drive Ford's biggest SUV or if your SuperDuty truck is equipped with bucket seats and a center console, this Stealthbox® model is right up your alley. Without infringing on people space and without being visible, it will fill your interior with rich, deep bass.
This compact unit installs inside the factory center console. The cup holders remain unaffected and some console storage is retained. A powerful JL Audio 10-inch subwoofer driver fires down into the floor for intense up-front bass presence.
The Hard Data: Contains one 10W3v3-2 in a sealed enclosure. 500 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside factory center console and fires down on the floor. Cupholders are not affected. For installation into front console only. Console storage is reduced. The factory console is not supplied with the Stealthbox®. After installation, the factory console is raised approximately 1.5 inches above the floor. Will not fit in SuperDuty trucks with bench seats. Will not fit consoles with rear cup holders and rear audio controls.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-F-SUPRCNSL/10W3v3 Installation Manual
Single 10-Inch 2-Ohm Thin 300-Watt Subwoofer-Enclosure for Select 2014-2018 Chevrolet-Silverado and GMC-Sierra Pickups, with Front Bucket-Seats and Factory-Console
GM’s third generation Silverado/Sierra gets a full redesign with a variety of enhancements including engine and technology upgrades. Regrettably, the factory audio systems still come up short when it comes to bass reproduction.
Designed to invisibly install in the factory console, this Stealthbox® adds impressive, high-quality bass, with zero loss of passenger space, storage space, or utility. The only thing you lose is that weak factory bass performance.
Featuring 100% fiberglass construction, this Stealthbox® is equipped with a down-firing 10-inch TW1 thin-line subwoofer in a sealed enclosure design.
The Hard Data: Contains one 10TW1-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside forward-most portion of front center console, without affecting storage space or cup holders. Replaces the OEM “subwoofer” system, if vehicle is so equipped. Will not fit trucks equipped with eAssist powertrain.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-3GSLVCNSL/10TW1 Installation Manual
Single 10-Inch Thin 300-Watt Subwoofer-Enclosure for Select 2015-2020 Cadillac-Escalade, Chevy-Suburban, Chevy-Tahoe and GMC-Yukon Vehicles, with front bucket-seats and factory center-console
The fourth generation full-size SUV from GM gets all-new, luxurious interiors, along with major enhancements in performance and technology. Unfortunately, the stock audio systems continue a track record of weak bass reproduction. There also isn’t much room for a conventional subwoofer design, without compromising people and cargo space.
To neatly solve this problem, JL's engineers have designed a subwoofer solution that installs invisibly, inside the factory console, with zero loss of console storage space.
Featuring 100% fiberglass construction, this Stealthbox® is equipped with a down-firing 10-inch TW1 thin-line subwoofer in a sealed enclosure design.
The Hard Data: Contains one 10TW1-2 in a sealed enclosure. 300 watt power handling. Wired for 2 ohm mono. Stealthbox® installs inside forward-most portion of front center console, without affecting storage space or cup holders. Replaces the OEM “subwoofer” system, if vehicle is so equipped.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-4GSUVCNSL/10TW1 Installation Manual
Single 10-Inch 2-Ohm 400-Watt Subwoofer-Enclosure for Select 2021-UP Large Chevrolet and GMC SUV Vehicles
GM's fifth-generation full-size SUV gets all-new, luxurious interiors, along with major enhancements in performance and technology. Unfortunately, the factory audio systems still lack quality bass reproduction. There also isn’t much room for a conventional subwoofer design, without compromising people and cargo space.
To overcome this challenge, JL-Audio engineers developed a subwoofer solution that installs invisibly, behind the driver's side cargo panel, with no loss of storage space. Featuring 100% fiberglass construction, this Stealthbox is equipped with one of JL's innovative, 10-inch TW3 thin-line subwoofers in a custom-formed, sealed enclosure.
The Hard Data: Contains one 10TW3-D4 in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Stealthbox® installs behind the driver side cargo trim panel. Replaces the OEM “subwoofer” system, if equipped.
Applications
Escalade
Escalade ESV
Suburban
Tahoe
Yukon
Yukon XL
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-5GSUV/10TW3 Installation Manual
Single 10-Inch 2-Ohm 400-Watt Thin Subwoofer-Enclosure for Select 2014-Up Corvette C7 Stingray Vehicles
The seventh-generation Corvette establishes a new benchmark for performance and style, but like most sports cars, presents a challenge when it comes to achieving excellent bass performance.
This Stealthbox® solution is engineered for those wanting to keep most of the cargo space in the hatch. It is also designed to install without any screws or bolts and can be removed in seconds for track day and reinstalled just as fast. The factory targa-top stowage is not affected in any way by the Stealthbox®, so you can enjoy great bass with or without the top installed.
Inside this Stealthbox® is a potent JL Audio 10-inch thinline subwoofer driver in a sealed enclosure that is expertly matched to the Corvette's acoustics. Also available with dual 10TW3 drivers model.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2-ohm mono. Installs into driver side hatch storage compartment. Steel mesh grille is included to protect the subwoofer driver. Installation does not affect storage of targa-top. No holes need to be drilled for installation. Easy to remove and replace. Use of driver's side, rear storage compartment is lost with installation. Storage compartment lid must be removed for installation, but can be replaced if Stealthbox® is removed. Will not fit convertible model.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-C7CP1/10TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2014-Up Corvette C7 Stingray Dual-Driver Vehicles
The C7 Corvette offers an aggressive exterior and a jetfighter-like cockpit, along with major increases in horsepower, torque and technology. Still missing, however, is a real subwoofer system… even with the premium audio option.
To solve this problem, the JL Audio engineers developed a potent Stealthbox® design housing twin 10TW3 subwoofers in a sealed enclosure that mounts ahead of the rear axle, so as to preserve precious cargo space and maintain the C7’s excellent weight distribution. With up to 800W of power handling, this Stealthbox® delivers amazing sub-bass output matching your Corvette’s powerful engine, adding even more enjoyment to every minute you spend on the road. Also available with single 10TW3 driver model.
The Hard Data: Contains two 10TW3-D8 subwoofers in a sealed enclosure. 800 watt power handling. Wired for 2 ohm mono. Installs behind front seats in the forward section of the cargo area. Installation does not affect storage of targa-tops. Steel mesh grilles are included to protect the subwoofer drivers. Will not fit convertible model.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-C7CP2/10TW3 Installation Manual
Single 12-Inch 2-Ohm 600-Watt Subwoofer-Enclosure for Select 2016-Up Chevrolet-Camaro Coupe Vehicles
Chevrolet’s 6th generation Camaro delivers a powerful shot of adrenalin and all-American, classic muscle car looks. Unfortunately, its stock sound system lacks real low-frequency punch and definitely needs some help in the bass department.
This Stealthbox® is designed to produce powerful amounts of ultra-deep bass with minimal loss of useful cargo space. Its 100% fiberglass sealed enclosure houses a highly potent 12W6v3 JL Audio 12-inch subwoofer and neatly tucks into the driver side, rear corner of the trunk. Rear-seat pass-through functionality remains unaffected, and full access to the under floor battery compartment is retained. Also available in 12TW3 driver model.
The Hard Data: Contains one 12W6v3-D4 in a sealed enclosure. 600 watt power handling. Wired for a 2 ohm load. Installs in the driver side rear corner of the trunk. Minimal loss of trunk space. Black steel mesh woofer grille included. Installation requires permanent modification to the driver’s side trunk liner. Will not fit convertible models!
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-CAM6G/12W6v3 Installation Manual
10-Inch 2-Ohm 400-Watt Thin Subwoofer-Enclosure for Select 2015-2022 Chevrolet-Colorado and GMC-Canyon Crew-Cab Vehicles
GM’s mid-size truck returns with major enhancements in power and technology, all packaged in a larger body and upscale interior with all the trimmings. Unfortunately, the factory audio systems are still lacking in the bass delivery department.
JL's Stealthbox® features an all-fiberglass, sealed enclosure design that installs under the rear seat and requires no holes to be drilled for installation. Equipped with their revolutionary 10TW3 thin-line subwoofer, this Stealthbox® fills your truck with powerful, deep JL Audio bass, with no intrusion on cab space.
The Hard Data: Contains one 10TW3-D4 subwoofer in a sealed enclosure. 400 watt power handling. Wired for 2 ohm mono. Installs under the rear bench seat. Does not affect folding or reclining of seat. Requires removal of under seat storage tray.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-COCREW2G/10TW3 Installation Manual
Dual 12-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2007-2013 Chevrolet-Silverado and GMC-Sierra Crew-Cab Trucks with Ebony-Interior
Whether your truck is used to work hard or play even harder, this vehicle brings a whole lot to the table: from great towing and hauling capabilities to powerful engine options, a spacious interior and a smooth ride. Amidst an evolving truck market complicated with special features and touch screens, the massive GM Crew Cab trucks have stuck to their model of simplicity and comfort.
JL Audio's Stealthbox® enhances this design by adding quality bass without losing precious space or functionality. The Stealthbox® slips under the truck's rear seat and features two of JL's revolutionary 12TW3 thin-line subwoofers, giving you absolutely stellar sub-bass impact and quality. They even left a perfect spot for a clean amplifier installation!
The Hard Data: Contains two 12TW3-D8 subwoofers in a down-firing sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs under rear seat. Will not affect the folding of the rear seat or rear leg room.Will not fit “Classic” models.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCC2/12TW3/BK Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2014-2018 (Gen 3) Chevrolet-Silverado and GMC-Sierra Crew-Cab Trucks
This generation of Chevrolet/GMC trucks is bringing new levels of interior refinement and technology to the full-size truck segment. JL's Stealthbox® enhances all this by adding impressive, high-quality bass without losing any of your precious people space or interior functionality.
The Stealthbox® slips under the truck's rear seat and features two of JL Audio's revolutionary 10TW3 thin-line subwoofers, giving you absolutely stellar sub-bass impact and quality. They even left a perfect spot in the middle of the enclosure for a clean, hidden amplifier installation!
The Hard Data: Contains two 10TW3-D8 subwoofers in a down-firing sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs under rear seat. Will not affect the folding of the rear seat or rear leg room.
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCC3/10TW3/BK2 Installation Manual
Dual 12-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 2019-UP (Gen 4) Chevrolet-Silverado and GMC-Sierra 1500 Crew-Cab Trucks, 2020-UP for 2500 and 3500 HD
This generation of Chevrolet/GMC trucks is bringing new levels of interior refinement and technology to the full-size truck segment. JL's Stealthbox® enhances all this by adding impressive, high-quality bass without losing any of your precious people space or interior functionality.
The Stealthbox® slips under the truck's rear seat and features two of JL Audio's revolutionary 12TW3 thin-line subwoofers, giving you absolutely stellar sub-bass impact and quality. We even left a perfect spot in the middle of the enclosure for a clean, hidden amplifier installation!
The Hard Data: Contains two 12TW3-D8 subwoofers in a down-firing sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs under rear seat. Will not affect the folding of the rear seat or rear leg room.
Applications
CHEVROLET
Silverado 1500
2019-2024
Silverado 2500 HD, 3500 HD
2020-2024
GMC
Sierra 1500
2019-2024
Sierra 2500 HD, 3500 HD
2020-2024
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCC4/12TW3 Installation Manual
Dual 10-Inch 2-Ohm 800-Watt Thin Subwoofer-Enclosure for Select 1999-2006 Chevrolet-Silverado, GMC-Sierra Crew-Cab Trucks and 2007 Crew-Cab-Classic Trucks
The massive GM Crew Cab trucks offer limousine-like rear seat room and comfort, accomplished by effectively utilizing almost every cubic inch of interior space. JL Audio's Stealthbox® for these big trucks slips behind the rear seat and features twin 10TW3 subwoofers for absolutely stellar sub-bass impact and quality. Nobody will ever know it's there, until you turn it up.
The Hard Data: Contains two 10TW3-D8 subwoofers in a sealed enclosure. 800 watt power handling. Wired for a 2 ohm load. Installs behind the rear seat. Will not affect the folding of the rear seat or rear leg room.
Applications
CHEVROLET
Silverado 1500, 2500, 3500
1999-2006
Silverado Classic
2007
GMC
Sierra 1500, 2500, 3500
1999-2006
Sierra 1500 Classic
2007
Stealthbox® products are built to order and generally ship within 5-6 business days of receiving your order.
JL Audio SB-GM-SLVCRW/10TW3 Installation Manual
