All

TW5-Series 13.5-Inch 600-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm SVC The JL Audio 13.5" TW5v2 thin subwoofer driver uses a chassis with a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the subwoofer chassis than with conventional thin sub designs, while allowing excellent linear excursion capability and mechanical stability. The 13TW5v2 improves upon the original 13-Inch TW5 driver with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is available in single 2-ohm and single 4-ohm voice coil configurations. In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 12-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer. The JL Audio 13TW5v2-2 and the 13TW5v2-4 thin subwoofers are best used with amplifier power in the 250-Watt - 600-Watt range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure. Never has such high-quality subwoofers-bass been possible in the most challenging thin installation applications. General Specifications Continuous Power Handling 600W RMS Recommended Amplifier Power 250W - 600W RMS Nominal Impedance 2Ω JL Audio 13TW5v2 Manual

Read more less

C2-Series 5.25-Inch 60-Watt Component Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs. The C2-525 system features 5.25-inch (130 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB JL Audio C2-525 Manual

Read more less

C2-Series 5.25-Inch 60-Watt Component Woofer, with Grille The C2-525cw is a 5.25-inch (130 mm) component woofer capable of accurate reproduction between 63 Hz and 8 kHz. It features a mineral-filled polypropylene cone and stamped steel basket. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. A grille is included, consisting of a black grille tray and a black steel mesh grille. Sonic character: Clean and Powerful Sold individually. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 150 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 8 KHz ± 3 dB JL Audio C2-525 Manual

Read more less

C2-Series 5.25-Inch 60-Watt Coaxial Speaker System The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-525x system features 5.25-inch (130 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB JL Audio C2-525x Manual

Read more less

C2-Series 6.5-Inch 60-Watt Component Woofer with Grille The C2-650cw is a 6.5-inch (165 mm) component woofer capable of accurate reproduction between 59 Hz and 6 kHz. It features a mineral-filled polypropylene cone and stamped steel basket. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. A grille is included, consisting of a black grille tray and a black steel mesh grille. Sonic character: Clean and Powerful Sold individually. General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 150 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 6 KHz ± 3 dB JL Audio C2-650 Manual

Read more less

C3-Series 5x7" 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. Many people mistakenly believe that an oval speaker cannot perform as well as a round one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C3-570 system features 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are not available for this product. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-570 Manual

Read more less

C3-Series 5x7-Inch 75-Watt Component Woofer with Grille There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. Many people mistakenly believe that an oval speaker cannot perform as well as a round one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C3-570cw is a 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofer with oversized 1.2-inch (30.5 mm) voice coil, mineral-filled polypropylene cone and injection-molded polymer basket. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. Woofer grilles are not available for this product. Sonic character: Clean and Powerful Sold individually. Includes Component Phase Plug and Tweeter Post (Tweeter sold separately). General Specifications Continuous Power Handling (RMS) 75 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB Physical Specifications Frame Outer Diameter* (A) 5.52 x 7.68 in / 140 x 195 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 4.08 in / 104 mm Frontal Coaxial Tweeter Protrusion** (D) 0.78 in / 20 mm Frontal Grille Protrusion (E) N/A Mounting Hole Diameter (F) N/A Mounting Depth (G) 2.52 in / 64 mm JL Audio C3-570cw Manual

Read more less

C3-Series 6.5-Inch 75-Watt Convertible Component Speaker System There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650 system features 6.5-inch (165 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. General Specifications Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB JL Audio C3-650 Manual

Read more less

C3-Series 6.5-Inch 75-Watt Component Woofer with Grille There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-650cw is a 6.5-inch (165 mm) component woofer with an oversized 1.2-inch (30.5 mm) voice coil, mineral-filled polypropylene cone and injection-molded polymer basket. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. A woofer grille is included, consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold individually. Includes Component Phase Plug and Tweeter Post (Tweeter sold separately). General Specifications Continuous Power Handling (RMS) 60 W Peak Music Power 150 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 6 KHz ± 3 dB Physical Specifications Frame Outer Diameter (A) 6.50 in / 165 mm Grille Tray Outer Diameter (B) 6.74 in / 171 mm Motor Outer Diameter (C) 4.08 in / 104 mm Frontal Coaxial Tweeter Protrusion* (D) 0.75 in / 19 mm Frontal Grille Protrusion** (E) 1.03 in / 26 mm Mounting Hole Diameter (F) 5.56 in / 141 mm Mounting Depth (G) 2.55 in / 65 mm JL Audio C3-650cw Manual

Read more less

C6-Series 6.5-Inch 75-Watt Component Audiophile Speaker System Born from shared technologies used in JL's flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features: Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding mid-bass impact, linearity and low distortion Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels Cast alloy frame with JL's Elevated Frame Cooling feature Includes fine mesh grilles C6 Tweeter Features: Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping Neodymium motor delivers high magnetic flux from a compact motor design Ferrofluid cooling and damping improves reliability and response smoothness Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz – 21 KHz ± 3 dB JL Audio C6-650 Manual

Read more less

C7-Series 6.5-Inch 125-Watt Component Woofer with Grille C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from their most advanced development tools and a complete commitment to precision manufacturing. The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviors. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C7-650cw Design Notes:Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high frequency behavior. Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw's outstanding excursion capability. Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver's performance range. A 32 mm (1.27 inch) diameter, overhung voice coil is employed, wound with copper wire onto a fiberglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area, and our Patented Elevated Frame Cooling technology. Design Bandwidth: With 48 dB/octave filters: 50 Hz - 5 kHz With 24 dB/octave filters: 60 Hz - 5 kHz With 12 dB/octave filters: 70 Hz - 5 kHz Built in USA with Global Components Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert. The performance of every C7 driver is tested and verified, then assigned a unique serial number. Register your C7 loudspeaker online to receive a copy of its specific Acoustical Test Report. General Specifications Continuous Power Handling (RMS) 125 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 50 - 175 W / Ch. Nominal Impedance 4 Ω Frequency Response 50 Hz - 5 KHz ± 3 dB JL Audio C7-650cw Manual

Read more less

6.5-Inch 90-Watt RMS Convertible Component Automotive Door Speakers The 6.5" QS series audiophile component door speakers by Kicker offer stunning midrange drivers, audiophile precise tweeters and a superior crossover network. The QS 6-1/2 Inch convertible speakers are a matched component system, built for pure sonic reproduction.  The Kicker 41QSS654 crossovers allow you to use a single amplifier channel, or use bi-amplification for even more flexibility and control. These 6.5" QS series convertible speakers can be installed as a pair of components or a coaxial configuration. These Kicker speakers work best with 90 watts of recommended power. See below for more details. Specifications Woofer (in., mm) 6 1/2, 160 Tweeter (in., mm) 1 3/16, 30 Tweeter dome material Tetoron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 90 Peak Power (watts, per ANSI/CTA-2031-A) 180 Sensitivity [1W, 1m] 86dB Frequency Response [Hz] 50 - 22k Woofer Mounting Hole Diameter [in, mm] 5 1/16, 129 Woofer Bottom Mount Depth [in, mm] 2 1/2, 63.5 Flush Mount Tweeter Hole Diameter [in,mm] 1 13/16, 46 Flush Mount Tweeter Depth [in,mm] 1 1/8, 29 High Pass [dB], at Frequency [Hz] 24, 2800 Low Pass [dB], at Frequency [Hz] 12, 2800 High Frequency Output Attenuation [dB] 0, +3, +6 Kicker QSS Series Manual

Read more less

6.75-Inch 100-Watt RMS Convertible Component Automotive Door Speakers The 6.75" QS series audiophile component door speakers by Kicker offer stunning midrange drivers, audiophile precise tweeters and a superior crossover network. The QS 6-3/4 Inch convertible speakers are a matched component system, built for pure sonic reproduction.  The Kicker 41QSS674 crossovers allow you to use a single amplifier channel, or use bi-amplification for even more flexibility and control. These 6.75" QS series convertible speakers can be installed as a pair of components or a coaxial configuration. These Kicker speakers work best with 100 watts of recommended power. See below for more details. Specifications Woofer (in., mm) 6-3/4, 165 Tweeter (in., mm) 1-3/16, 30 Tweeter dome material Tetoron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 100 Peak Power (watts, per ANSI/CTA-2031-A) 200 Sensitivity [1W, 1m] 87dB Frequency Response [Hz] 40-22k Woofer Mounting Hole Diameter [in, mm] 5-7/16, 138 Woofer Bottom Mount Depth [in, mm] 2-1/2, 63.5 Flush Mount Tweeter Hole Diameter [in,mm] 1-13/16, 46 Flush Mount Tweeter Depth [in,mm] 1-1/8, 29 High Pass [dB], at Frequency [Hz] 24, 2800 Low Pass [dB], at Frequency [Hz] 12, 2800 High Frequency Output Attenuation [dB] 0, +3, +6 Kicker QSS Series Manual

Read more less

8-Inch 300-Watt Thin Subwoofer Driver, 2-Ohm DVC The CompRT 8" thin subwoofer by Kicker is a weather resistant thin sub with a 2Ω dual voice coil design. This thin 8 inch sub magnet structure delivers 300W RMS of power with a chassis mounting depth of just under 2 3/4". The Kicker designed UniPlate™ back plate and solid pole piece serve as a single heat-absorbing unit to keep this 8" CompRT thin subwoofer driver nice and cool.The CompRT 8-Inch subwoofer works best with a sealed or ported enclosure and 300 watts of recommended power. Specifications SIZE [in, cm]: 8, 20 IMPEDANCE [Ohms]: 2 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 SENSITIVITY [dB 1w/1m]: 81.8 MOUNTING DEPTH [in, cm]: 2 11/16, 6.7 MOUNTING DIAMETER [in, cm]: 7, 17.7 MIN SEALED BOX VOL [cu. ft, L]: 0.2, 5.66 MAX SEALED BOX VOL [cu. ft, L]: 1.0, 28.32 MIN VENTED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX VENTED BOX VOL [cu. ft, L]: 1.2, 34 Kicker CompR Subwoofer Manual

Read more less

6-3/4" 100-Watt Coaxial Speakers This pair of QS series 6.75" coaxial audiophile speaker drivers by Kicker feature neodymium magnets on the woofer and tweeter, and are bi-amp capable. Incased within the speaker chassis is you will find a 25mm Teteron® dome tweeter with Kicker's custom wave guide technology for near perfect phase alignment for smooth frequency response. The injection-molded Polypropylene cone of this coaxial door speaker is impregnated with carbon-fiber for tight, accurate midrange. An NBR rubber surround provides superior damping, and complemented by a signature blue double surround stitching. The independent 18dB crossover has been optimized for size, and features built-in tweeter protection. Utilizing Metallized Polypropylene capacitors, high-powered resistors and audiophile-grade air-core inductors, the crossover delivers outstanding overall sound quality and easy mounting in a door or under a seat. These Kicker QS 6-and-3/4 inch door speakers have an amplified RMS power range of 100W. This pair of drivers also has speaker adaptor rings, allowing them to be installed using select factory location mounting. Specifications Woofer (in., mm) 6 ¾, 165 Tweeter (in., mm) 1, 25 Tweeter dome material Teteron® Rated Impedance [Ω] 4 Recommended Amplifier Power (watts RMS) 100 Peak Power (watts, per ANSI/CTA-2031-A) 200 Sensitivity [1W, 1m] 86dB Frequency Response [Hz] 40-20k Woofer Mounting Hole Diameter [in, mm] 5 9/16, 141 Woofer Mounting Depth [in, mm] 2 9/16, 64.9 High Pass [dB], at Frequency [Hz] 18, 5.5k Low Pass [dB], at Frequency [Hz] 18, 5.5k Comments Crossover is bi-amp capable. Kicker QS Series Coaxial Speaker Manual

Read more less

Four-by-Ten-Inch Coaxial Speaker Drivers, 75-Watt RMS KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Specifications Speaker Design 2-Way Woofer [in, mm] 4x10, 100x250 Tweeter [in, mm] ½, 13 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 88 Frequency Response [Hz] 45-20k Mounting Hole Diameter [in, mm] 3-7/8 x 9-3/8, 99 x 238 Top Mount Depth [in, mm] 2-3/8, 61 Bottom Mount Depth [in,mm] 2-13/16, 71 Tweeter Protrusion [in,mm] 0 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

Read more less

5-1/4-Inch Coaxial Speaker Drivers, 75-Watt RMS The Kicker KS series five-and-a-quarter-inch coaxial speakers come with three custom bracketing options, built specifically to fit in today’s GM, Chrysler, Subaru, Toyota and Jeep factory speaker locations. KS series speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 5-1/4, 130 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 45-21k Mounting Hole Diameter [in, mm] 4-1/2, 115 Top Mount Depth [in, mm] 1-3/4, 45 Bottom Mount Depth [in,mm] 2, 52 Tweeter Protrusion [in,mm] 1/4, 6 Grilles Yes Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

Read more less

Six-by-Eight-Inch Coaxial Speaker Drivers, 75-Watt RMS The Kicker KS series six-by-8-inch coaxial speakers let you play at concert-like volume, yet maintain the smoothness and subtlety to please even the most selective ear. They work best with 15 to 75 watts of recommended power. High power handling Tough rubber surrounds Thin-mount design easily fits behind factory grilles Brackets for select GM/Chrysler/Subaru/Jeep and Toyota included Specifications Speaker Design 2-Way Woofer [in, mm] 6 x 8, 160 x 200 Tweeter [in, mm] ¾, 20 Rated Impedance [Ω] 4 Recommended Amplifier Power [Watts RMS] 15-75 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 45-21k Mounting Hole Diameter [in, mm] 5 x 7-3/16, 127 x 182 Top Mount Depth [in, mm] 2-1/4, 58 Bottom Mount Depth [in,mm] 2-5/8, 67 Tweeter Protrusion [in,mm] 1/16, 2 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material Silk Woofer Cone Material Polypropylene Woofer Surround Material Rubber Kicker KS Series Coaxial Speaker Manual

Read more less

8-Inch 300-Watt Thin Subwoofer Driver, 2-Ohm or 4-Ohm DVC The CompRT 8-inch subwoofer is an all-weather thin bass driver with a pair of 2-Ohm or 4-Ohm voice coils. With a mounting depth under three inches and plenty of power handling, this go-anywhere sub is as flexible as it is powerful. A UV-resistant cone and surround help make the CompRT sound great wherever the road (or trail) takes you. An advanced suspension and heat management system helps to keep the bass powerful, deep and consistent. To make Kicker subs even more reliable, their engineers developed Forced-Air Cooling™ to help these thin subs run 20 percent cooler than before. Kicker signature red double stitching makes an outstanding bond between the improved Santoprene surround and polypropylene woofer cone. Revolutionary SoloKon™ technology joins the cone to the vented back brace, creating a single integrated unit that both cools the motor and eliminates distortion. The CompRT 8-Inch 48CWRT82 and 48CWRT84 subwoofers work best with a sealed or ported enclosure and 300 watts of recommended power. Specifications SIZE [in, cm]: 8, 20 IMPEDANCE [Ohms]: 2 or 4 DVC Recommended Amplifier Power (watts RMS) 300 Peak Power (watts, per ANSI/CTA-2031-A) 600 SENSITIVITY [dB 1w/1m]: 81.8 MOUNTING DEPTH [in, cm]: 2 11/16, 6.7 MOUNTING DIAMETER [in, cm]: 7, 17.7 MIN SEALED BOX VOL [cu. ft, L]: 0.2, 5.66 MAX SEALED BOX VOL [cu. ft, L]: 1.0, 28.32 MIN VENTED BOX VOL [cu. ft, L]: 0.8, 22.7 MAX VENTED BOX VOL [cu. ft, L]: 1.2, 34 Kicker CompRT Subwoofer Manual

Read more less